I have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
Wireless internet connection stops working after anywhere from 10 minutes to two hours, a message pops up telling me it is "impossible to connect to my preferred wireless network", and then it fails to detect any wireless connections at all. The strangest thing is that when I try to "repair" the connection, which used to work, the computer immediately shuts down and restarts itself. It also seems like when I attempt to download something, like a movie for example, the connection fails right away, while if I'm just surfing the web it usually lasts around an hour before stopping. And when I restart the computer again it works perfectly fine at first, like right now, but eventually does the same thing.
View 9 Replies View RelatedWhen I start my laptop, an Acer 7715Z, it will try to connect to the internet, but often fails.I then try it a few times manually. But the first 5 minutes I can try as often as I like but it will give a 'problem' popup, offering me a windows troubleshooter (which doesn't find the problem).I just have to try manually over and over again until it finally connects.Then my problems are over and I can internet without loosing connection. This doesn't only happen at home, but also when I'm at relatives. So my modem or ISP is not the problem. Also, my other equipment works just fine (mac, iphone, ipod, netbook).I've updated the Broadcom 802.11n adapter driver, run a virus/malware check, etc. but nothing works.The wireless lan adapter I assume basically works ok as it doesn't loose connection once I get online? Is there another setting I could check or optimise? I find it so strange. It's like the first 20-30 times trying to manually connect something is blocking it and once I get through I'm online without problems or losing connection. As I mentioned earlier, my other equipment go online almost immediately. Is there some windows setting that could block my manual attempts for a few times before letting me in? Could the broadcom adapter be faulty after all, even when after connecting it stays connected and problem free? Any control panel or other setting I could check first before sending it to be checked/repaired?
View 6 Replies View RelatedIncorrect password attempts in ACS 4.2.
1) Can I specify the time in "Incorrect password attempts" ? means if the 3 incorrect password attempt was made with in 05 minutes, then only the account will be locked ?
2) Is it possible to RESET automatically the "Incorrect password attempts counter" (when the account locked) into ACS?
I already have traditional IPsec VPN access working just fine through this device. Users connect and authenticate using a windows AD server for RADIUS and everything works great. However, the customer wants to use AnyConnect instead of the traditional VPN client. So I added a SSL connection profile (the anyconnect essentials feature is enabled on the device) and told it to use the same IP pool and RADIUS server group as the IPsec clients. I used the ASDM wizard to configure it and had no issues completing the wizard. when trying to make a connection to the webvpn portal I get a 404 error instead of the client portal. Also when trying to connect with the Anyconnect client, I get the usual "Untrusted VPN certificate" warning, but the connection attempt fails when I click through it.The strange part is when I look at the issued certificate in the browser or the client, it's showing me the certificate from the RADIUS server. Why is it looking there for certificate and more importantly, why does it care at all about a certificate when I've specified in the connection profile to use AAA to authenticate?
View 1 Replies View RelatedHow to Configure "Incorrect password Attempts Disable login for 30 minutes after 3 successive failed attempts" on ASA-5510???
View 3 Replies View RelatedIs it possible for the wlc (5500) block wireless users attempting to login to the network more than 3 times?I have several devices trying to connect to the network automatically using rhe old password, after 3 attempts the account will lock out! Im running peap mschapv2 with radius and active directory.
View 1 Replies View RelatedI have setup ACS 5.2 in my lab and have it completely funcation with Downloadable ACLs, Dynamic VLANs and the identity store on the backend is Active Directory. I need it to lock a user account in AD if there are to many auth attempts. I have gone into AD and set a max login attempts to 3 but if I continue to fail authentication (on purpose) using radius auth, it never locks out my AD account? I am using the Anyconnect 3.0 with NAM as the supplicant installed on my workstation. I have also configured the switchport that I am connect to with the following commands. I tried the dot1x max-reauth-req 3 command and that didn't really do anything for me either. What am I missing here?
switchport mode access ip access-group 10 in authentication event fail action authorize vlan 40 authentication event no-response action authorize vlan 40 authentication host-mode multi-host authentication priority dot1x mab authentication port-control auto authentication timer reauthenticate 10 authentication timer inactivity 20 authentication violation protect mab dot1x pae authenticator dot1x timeout quiet-period 5 dot1x timeout tx-period 5 dot1x max-req 3 spanning-tree portfast
I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 Replies View RelatedI have a TAC on this, but thought I would throw it out here too. We recently upgraded a 5520 to 8.4 code so HTTPS traffic can filter through the CSC. Well, it takes several attempts to pull up any https pages. Cisco thought it may be hardware, so I swapped out the CSC, but before I go through the hassle of moving licnese, I brought a second ASA with CSC, which prior to this was their main ASA running 8.2 code and did not have issues, of course HTTPS did not filter through it either. the exact same thing happened on this ASA. So apparently it is not hardware related. One other thing I found, if I bypass https, it still happens, and the only solution is to shut down the CSC module. Now I think it may be the ASA policy that while not the cause, but is being difficult. I found that if you pull SIP inspections out, and reapply them in testing voice issues, you must reboot the ASA for them to work again. I am wondering if this is the case with the HTTPS traffic not releasing from the CSC even with the ACL having it removed. I need to try that next.
View 4 Replies View RelatedI have ACS1121 running version 5.1.0.44.6 on my network environement , I need to enable account lock-out for internal user during failed attempt for more than 8 times , How to achieve this . I could see account lock-out for administrator user account , not for internal user .
View 2 Replies View Relatedbought a mini usb wifi adapter for my new computer i built from monoprice. the website says all u need to do is download the drivers from realtek and install and the unit will run. ive tried to install the driver multiple times, and when i go into the devices window, it says there is no device installed for the adapter. also after attempting to install, a bubble pops up on the task bar saying that driver did not install correctly after setup completes and reboots.
View 3 Replies View RelatedWhenever I try to login to the router, it fails to recognise the username and password for usually the first 5 or 6 attempts, then recognises them on the 6th or 7th. Not eactly a massive issue, but coupled with what seems to be a very unstable connection makes me wonder if it was a good move to buy cisco.
View 3 Replies View RelatedI am developing CAP1602I & 2500 Controller.The CAP1602I-E-K9 can't register with the 2500 controller. [code] logging appears: capwap can't process uncryped data..I even didn't configure capwap on CAP1602.May I know if CAP1602 doesn't support LWAPP? Why LWAPP doesn't work?According to the logging, I also tried to configure the "Data Encryption" on 2500 controller ( according to 7.0.116.0 guide)
"Cisco 2500, WiSM2, WLC2—By default, these platforms do not contain DTLS. To turn on data DTLS, you must install a license. These platforms have a single image with data DTLS turned off. To use data DTLS you will need to have a license."Note If your controller does not have a data DTLS license and if the access point associated with the controller has DTLS enabled, the data path will be unencrypted. I should purchase a license? or, if I can configure the CAP1602I to don't encrypt data?
Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies View RelatedWe have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies View RelatedWe have a 5508 controller that manages AP's at approximately 20 branches - each branch has their own subnet. We have a single branch (subnet) with new 2602 AP's that will not register with the controller. All communications to this subnet appear normal and there are no ACL's in place between the AP's and the controller. The AP's are able to resolve the controller IP address via DNS and begin the registration process but then timeout. We have successfully installed 2602 AP's at other branch locations and they register with no problems - this is only a problem at a single branch. I've attached some debug messages below for a single AP (this is a production environment so I parsed un-necessary info) and also included the console messages from a different AP (the console messages on the AP's are the same). There are currently 9 AP's at this location and none of them will register.
Debug Capwap Events:
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Discovery Request from 10.29.9.190:44306
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 300, joined Aps =272
[Code]......
We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies View RelatedJust tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies View RelatedI am trying to setup a new LG dp200 blue ray player to my home network and cannot get it to connect, but i can use my phone on it and my xbox. Ive reset the modem and reset the player back to factory defaults after a few failed attempts.
View 1 Replies View RelatedI am trying to configure the Wism running on a 6500 switch.... I have configured the DHCP scope for the AP on the controller itself with the same subnet as of the management for the controller. The AP gets the IP but once it restarts it doesn't register to the controller, this is the log i get on the AP when consoled into it. [code]
View 6 Replies View RelatedI have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedI have an AIR-LAP1141-A-K9 it keeps rebooting itself. It seems to boot up and loads the flash and then shortly afterwards and before I get to console login it reboots.in reviewing what I've captured from the boot process is a message "Unexpected exception to CPUvector 200, PC = 1020" Below it is the following "Traceback - 0x1020 0x51351c 0x51351c 0x513c00 0x4FB1A8 0x4FB5B0 0x4F7FB8 0x191214 0x1912c8 0x57090 0x57398 0x1A5E50" I tried a couple google searches but didn't have any luck finding anything that matched what I have occuring.
View 5 Replies View RelatedRegion : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP : TPG
RE: Voice SIP Account Phone Number Not Accepting 2 Characters My ISP TPG VoIP SIP account phone number is my TPG username rather than an actual normal telephone number. When I enter my 2 characters TPG username 'xx' as my TPG VoIP SIP account phone number as the 'Phone Number' field in the 'Voice - SIP Account' modem router management page on the LAN IP 192.168.1.1, then I press the 'Save' button, I encounter the error message "The length of 'Phone Number' is out of range[3,32]."I believe this error is due to my TPG SIP account Phone Number’ is not within the TD-VG3631 ‘Phone Number’ character length range from 3 to 32 inclusive.My old modem can register to my TPG VoIP account successfully with my TPG username 'xx' as the VoIP SIP account phone number.
I have contacted my ISP TPG and tried to get an actual VoIP SIP phone number. However, TPG does not provide an actual VoIP SIP phone number to their customers. TPG states I should use my TPG username as my VoIP SIP account phone number. They ask me to contact TP-Link to resolve the aforementioned error.Is there a way I can enter only 2 character TPG username as my VoIP SIP account phone number in the browser management page of the modem router? i.e. workaround, request TP-Link for a new firmware fix or else?
I have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies View RelatedWAP200E access point that causes it to reboot after anything from 15 to 20 mins .I have run it off an injector and a POE switch, updated the f/w to WAP200E-ETSI-FW-2.0.3.0 and it still reboots itself .I have even been sent a new one from the supplier and it does the same thing.
View 5 Replies View RelatedRegion : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version :
ISP : Engin
i purchased this new modem TD-VG3631 to replace my old one, Finished the internet configuration, it's ok, i can go to internet smoothly. however when i configured the voip function, i encountered a big problem, even i have entered all info which provided by Engin into your modem, it doesn't work. the status always down..Very sure it is not my account problem, because if i enter these info into my old modem , it works very well.
[code]...
I got my new comcast connection and using CISCO DPC3008 cable modem and EA6500 Wifi Smart Router. Internet works fine and then suddently the internet goes away. Further investigation shows EA6500 Wifi router just reboots every few hours and then wifi devices don't reconnect like it used to do with previous routers.
View 6 Replies View RelatedCheck to see if there is a firmware upgrade and there is. Well I updated it with the newest and only one out there. I did the upgrade, said sucessful and now it will just random reboot or something........ every few minutes the power light starts flashing....... then all the light go out, then power flashes again and it comes back up. I have tried many times to reflash it with that new firmware but no avail. I wish I had the old firmware back because it was working fine till I did this upgrade.
View 5 Replies View Related
