Acer 7715Z - Wireless Connection Fails On First Few Attempts?

Feb 11, 2013

When I start my laptop, an Acer 7715Z, it will try to connect to the internet, but often fails.I then try it a few times manually. But the first 5 minutes I can try as often as I like but it will give a 'problem' popup, offering me a windows troubleshooter (which doesn't find the problem).I just have to try manually over and over again until it finally connects.Then my problems are over and I can internet without loosing connection. This doesn't only happen at home, but also when I'm at relatives. So my modem or ISP is not the problem. Also, my other equipment works just fine (mac, iphone, ipod, netbook).I've updated the Broadcom 802.11n adapter driver, run a virus/malware check, etc. but nothing works.The wireless lan adapter I assume basically works ok as it doesn't loose connection once I get online? Is there another setting I could check or optimise? I find it so strange. It's like the first 20-30 times trying to manually connect something is blocking it and once I get through I'm online without problems or losing connection. As I mentioned earlier, my other equipment go online almost immediately. Is there some windows setting that could block my manual attempts for a few times before letting me in? Could the broadcom adapter be faulty after all, even when after connecting it stays connected and problem free? Any control panel or other setting I could check first before sending it to be checked/repaired?

View 6 Replies


ADVERTISEMENT

Canon MX892 Wireless Connection Fails?

Nov 23, 2012

I have set this "Black Friday" printer up and it shows it is transmitting wireless. However, I cannot get my PC to find it! I have tried everything I know. I am not an expert but is there something in my Verizon router that might be preventing it? I don't know what else it could be but maybe there is an expert out there that can.

View 5 Replies View Related

Screen Blinks Then In A Few Moments Wireless Connection Fails?

Oct 26, 2011

I'm running Windows 7. As stated in the title, once I see the screen blink, I know I have a few moments of connectivity left. The screen will continue to blink, then the wireless network connection icon goes red with an "x" through it. The computer continues to work (albeit with the screen blinking), but with no connection to the Internet. Checking Device Manager indicates no conflicts. Manually pressing the "wireless connectivity button" on this Compaq, which shows green=connected, only turns it red for a second, then back to green as if the adapter is enabled. Doing this prior to the blink-failure cuts the wireless connection as it should. I added iTunes about a month ago, the problem started about two weeks ago.

View 2 Replies View Related

Wireless Internet Stops Working / Attempts To Repair

Oct 16, 2011

Wireless internet connection stops working after anywhere from 10 minutes to two hours, a message pops up telling me it is "impossible to connect to my preferred wireless network", and then it fails to detect any wireless connections at all. The strangest thing is that when I try to "repair" the connection, which used to work, the computer immediately shuts down and restarts itself. It also seems like when I attempt to download something, like a movie for example, the connection fails right away, while if I'm just surfing the web it usually lasts around an hour before stopping. And when I restart the computer again it works perfectly fine at first, like right now, but eventually does the same thing.

View 9 Replies View Related

Cisco Wireless :: 2504 WLC Reboots When AP Attempts To Register

Jan 14, 2013

I have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
 
WLC2504 : 7.2.103.0
 
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)

View 3 Replies View Related

Acer Aspire 4920 Cannot Detect Wireless Connection

Oct 19, 2012

Why do my laptop can only detect the wireless connection when its placed beside the router? Other computer can detect the connection although it is far from the router. I'm using acer aspire 4920, windows 7.

View 6 Replies View Related

Linksys Wireless Router :: E4200 Internet Connection Fails

Jan 1, 2013

I have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.

View 3 Replies View Related

Linksys Wireless Router :: EA3500 - Connection Fails Frequently

Mar 14, 2013

I purchased and installed the above router to replace a working router that had a problem with our new condo location.  The old router couldn't access one of our computers.  The EA 3500 worked seamlessly for 6 months.  Now the connection fails intermittently (more times off than on) from that one computer.  It is two rooms over from the router & modem.  These are now in a fixed location that cannot be moved.

View 7 Replies View Related

Linksys Wireless Adapters :: WUSB600N V2 - Connection Fails - Can't Find WAP To Connect?

Apr 23, 2011

I purchased two WUSB600N V2 wireless adapters recently and have had nothing but problems on an otherwise stable network where I have iPads, iPhones, Netbooks, media centres, wireless printers, Notebooks and other USB PC-based network devices working without problems.
 
The WUSB600Ns are connected to desktop PCs, running WIndows XP SP3. I have removed the Linksys Network Management software and use Microsoft's wireless network management software.  I am running the latest drivers 1.4.10.0 for the cards. My WAP is a Belkin F5D-8236-4 running in WAP only mode. It is set to 40Mhz Channel 11 primary, Channel 7 secondary. Protected Mode is off, Broadcast SSID is on. I run WPA2-PSK AES for encryption. Note:  I've tried all combinations of bandwidth and channel settings.  I've run Netstumbler to find clear air channels - 11 seems best.
 
The issues are:

* seldomly connects at boot automatically without intervention.

* occasionally does not find WAP to connect to.

* sometimes will not connect to WAP - sits at "Acquiring Network Address".

* sometimes will not even get to Acquiring Network Address.

* Will often, once connected, after a while lose connection - the timeframe is inconsistent.
 
All of my other devices do not have these issues. I've been working on this issue for about a week trying to stabilise, even get a consistent failure pattern, but I'm about to send them both back.These are close to the most frustrating devices I've configured and I've got a lot of stuff on my network.

View 5 Replies View Related

Acer Aspire One 722 Notebook - Wireless Network Connection With Invalid IP Configuration

Aug 20, 2012

I bought a brand new acer aspire one 722 notebook and it works fine except I can't connect to the internet. After I run the diagnostics I get the following problem detected: "Wireless network connection doesn't have a valid ip configuration."

View 5 Replies View Related

Acer - No Internet Connection?

Apr 14, 2011

I cannot get internet access to my laptop. I DSL and wireless. It is showing that I am connected,but it says "No Internet access". I ran a diagnostic, and it told me the problem is- default gateway is not available.

View 1 Replies View Related

AAA/Identity/Nac :: ACS 4.2 Incorrect Password Attempts?

Nov 7, 2012

Incorrect password attempts in ACS 4.2.
 
1) Can I specify the time in "Incorrect password attempts" ? means if the 3 incorrect password attempt was made with in 05 minutes, then only the account will be locked ?
 
2) Is it possible to RESET automatically the "Incorrect password attempts counter" (when the account locked) into ACS?

View 0 Replies View Related

D-Link DIR-601 :: Router Connection To Internet Fails

Apr 13, 2011

I cant get this damn thing to connect to the internet (att dsl modem). I have ran the installation cd mulitple times and also configured it using the http. If i reset it while everything is hooked up and it makes an internet connection using DCHP (I think its called), but i need a PPPoE connection.

It seems to change my password (the username one that access the modem). The way i know is it always has more characters that the one i was provided by my isp with (*****). I dont enter any information other than my username or password (IP is dynamic).

I have a westell F90-6100 as my modem.

View 6 Replies View Related

Cisco VPN :: 878-K9 Router - Connection Fails After Some Time

Apr 27, 2011

I am running a Cisco 878-K9 Router, IOS 12.4(11)T1, as a Firewall with EasyVPNServer. The VPN Server was created with the wizard from the SDM.Everything works fine, BUT the VPN connections fail after about 10 minutes.

View 1 Replies View Related

Acer 5552 Laptop Will Not Get Internet Connection?

Apr 28, 2011

I have a Acer 5552 laptop and today it just stopped getting internet connection. I tried resetting the router and the computer neither worked. I also have a desktop and another laptop in my house and both of them are working and connecting fine. I am not sure what is going on. It finds the connection and says it is connected but then nothing will come up.

View 7 Replies View Related

Acer Aspire With Windows 8 - Keep Getting Limited Connection

Jan 22, 2013

I recently brought a new acer aspire with windows 8, it connects to the router/internet fine except every 10-20 mins (sometimes less) or so I get disconnected, my wifi icon in the tray shows a yellow '!', when I look in the wifi charm (the side bar thing) 'limited' is next to my routers name, but in reality It doesn't seem to have any connectivity atall.

View -1 Replies View Related

Acer 6930 - Ethernet Connection Keeps Dropping?

Aug 22, 2011

My ethernet connection keeps dropping and the only way to restore connectivity is to restart my laptop. It says "no internet access" and the connection remains even if I remove the cable. If I try disconnecting in Network and Sharing center it just keeps saying "attempting to disconnect".

I'm running Windows 7 Ultimate on an Acer 6930 laptop.

View 3 Replies View Related

Acer Notebook Internet Connection Lost

Jan 12, 2012

I have lost my wireless connection on my acer notebook... where is the button/switch etc to give me the blue flashing light to demonstrate connection to my wireless internet?

View 3 Replies View Related

Dell Latitude D600 Network Connection Fails

Feb 6, 2011

problem with my Dell Latitude D600 Laptop,I tried re-installing my OS, so now with a fresh new OS the wireless capabilities worked fine, but only for the first day, then the next morning the whole problem began again. Now it would say " No supported wireless adapters found" and when i would open the device manager some devices would have the yellow exclamation point, some of the devices would say "Intel PCIC compatible PCMICA controller" and " PCMICA MTD-0002" or just "card bus controller" and many other ones that would alternate when they appear. And also sometimes my network adapters would completely disappear from the list. I also tried scanning my whole drive for viruses and nothing was found.

Then i found that if you disconnect the wireless adapter physically and re connect it, it might work, but it didn't. I should also add that before this problem for some time i had another problem with the same laptop that had to do with the battery malfunctioning, and it displays a 4 orange , 1 green pattern sequence on the LED charge display. But it had never affected any of the laptops hardware or software before, so I don't know if that might have anything to do with it.

[code]...

View 1 Replies View Related

Cisco VPN :: 5510 - Connection Fails Using Full Tunnel?

Mar 31, 2012

We are using a 5510 and have issues trying to use VPN with full tunnel to connect from inside the firewall to a customer site. I don't seem to have a problem when using split tunnel profiles. How would you troubleshoot this?

View 12 Replies View Related

Cisco VPN :: AC 3.0 Full Tunnel Connection Fails After CSD Loads?

Jun 28, 2011

I have an AC 3.0 connection that works fine prior to CSD.  Once I've enabled CSD I get CSD to load and then the AC tunnel fails.  Ive attached the DART bundle and a few screen shots. 

View 3 Replies View Related

Cisco Routers :: PPTP Connection To RV220W Fails?

Jun 4, 2012

I've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
 
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.

View 6 Replies View Related

Cisco VPN :: Anyconnect Client Attempts Failing To ASA 5505

Apr 15, 2013

I already have traditional IPsec VPN access working just fine through this device.  Users connect and authenticate using a windows AD server for RADIUS and everything works great.  However, the customer wants to use AnyConnect instead of the traditional VPN client.  So I added a SSL connection profile (the anyconnect essentials feature is enabled on the device) and told it to use the same IP pool and RADIUS server group as the IPsec clients.  I used the ASDM wizard to configure it and had no issues completing the wizard. when trying to make a connection to the webvpn portal I get a 404 error instead of the client portal.  Also when trying to connect with the Anyconnect client, I get the usual "Untrusted VPN certificate" warning, but the connection attempt fails when I click through it.The strange part is when I look at the issued certificate in the browser or the client, it's showing me the certificate from the RADIUS server. Why is it looking there for certificate and more importantly, why does it care at all about a certificate when I've specified in the connection profile to use AAA to authenticate?

View 1 Replies View Related

Cisco Firewall :: ASA-5510 - Incorrect Password Attempts?

Sep 15, 2011

How to Configure "Incorrect password Attempts  Disable login for 30 minutes after 3 successive failed attempts" on ASA-5510???

View 3 Replies View Related

Acer One Can't Find Server - Connection Strength Strong?

Mar 2, 2011

i bought a second hand acer one net book for my daughters birthday in a couple of weeks when i first tried it it work i could go on the net, now it wont says can't find server. connection strength is strong 100% system is running ubuntu.

View 1 Replies View Related

Connection Fails - Connect During Safe Mode But Not On Normal Boot?

Apr 11, 2011

My PC Info: Tech Support Guy System Info Utility version 1.0.0.1

OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5850 @ 2.16GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3069 Mb
Graphics Card: ATI Mobility Radeon HD 3450 , 256 Mb
Hard Drives: C: Total - 305242 MB, Free - 252510 MB;
Motherboard: Dell Inc., 0F700C, , .8QQVVG1.CN4864388L1948.
Antivirus: Norton Security Suite, Disabled

So I am having issues connecting to the internet. I can connect during safe mode but not on normal boot. I ran a diagnostic and it said that the IP Gateway failed. I read a previous post and did the command promp "ipconfig/all" and this is what it said:

Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersEbony>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ebony-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....

I have norton, and have recently run Malwarbytes, Microsoft Malicious Removal Tool, and Dell PC Tune Up

View 6 Replies View Related

WRT160N - Video Chatting Fails And Disconnects Internet Connection

Aug 27, 2011

I can't seem to skype or video chat of any sort (ie: aim video chat, facebook video chat, etc.) on my computer. Whenever I start skype or try to start a video chat on aim/facebook, it fails and my internet disconnects for everyone. I don't know what could be wrong. Using the same wireless internet, my friends are able to video chat on their macbooks. It seems like my computer is the only one that can't video chat. Video chatting works when I use a sprint internet card. I have a sony vaio laptop running on windows 7. Our router in our apartment at school is a D-link wireless N? In addition to this problem, my internet loves to disconnect randomly too...this problem also persists at home with my Cisco Linksys router (model WRT160N V3) and Speedstream 5100 modem.

View 5 Replies View Related

Cisco Routers :: RV220W Remote PPTP VPN Connection Fails?

Jan 23, 2012

i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.

View 1 Replies View Related

Cisco VPN :: RV 120W Connection Fails With Banner Text Response

Sep 14, 2011

I have a CISCO RV 120W router. I have set it up with a static IP address from Verizon. Internet can be accessed.I just want IPSec passthrough for some people who can connect with Nortel contivity client to the company RSA server. I can make only one connection. The second connection fails with 'banner text' response issues. One connection always works. The router has the latest firmware. I have enabled IPsec passthru.

View 1 Replies View Related

Multiple Install Attempts - Still No Drivers Found For Usb Wifi Adapter

Sep 9, 2012

bought a mini usb wifi adapter for my new computer i built from monoprice. the website says all u need to do is download the drivers from realtek and install and the unit will run. ive tried to install the driver multiple times, and when i go into the devices window, it says there is no device installed for the adapter. also after attempting to install, a bubble pops up on the task bar saying that driver did not install correctly after setup completes and reboots.

View 3 Replies View Related

Linksys Cable / DSL :: WAG320N Multiple Login Attempts Needed

Apr 26, 2011

Whenever I try to login to the router, it fails to recognise the username and password for usually the first 5 or 6 attempts, then recognises them on the 6th or 7th. Not eactly a massive issue, but coupled with what seems to be a very unstable connection makes me wonder if it was a good move to buy cisco.

View 3 Replies View Related

Cisco :: 5500 / Disconnect Users After 3 Login Attempts On WLCs

Oct 15, 2011

Is it possible for the wlc (5500) block wireless users attempting to login to the network more than 3 times?I have several devices trying to connect to the network automatically using rhe old password, after 3 attempts the account will lock out! Im running peap mschapv2 with radius and active directory.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Using ACS 5.2 To Lock AD User Account If Too Many Authentication Attempts

Apr 18, 2011

I have setup ACS 5.2 in my lab and have it completely funcation with Downloadable ACLs, Dynamic VLANs and the identity store on the backend is Active Directory. I need it to lock a user account in AD if there are to many auth attempts. I have gone into AD and set a max login attempts to 3 but if I continue to fail authentication (on purpose) using radius auth, it never locks out my AD account? I am using the Anyconnect 3.0 with NAM as the supplicant installed on my workstation. I have also configured the switchport that I am connect to with the following commands. I tried the dot1x max-reauth-req 3 command and that didn't really do anything for me either. What am I missing here?
 
switchport mode access ip access-group 10 in authentication event fail action authorize vlan 40 authentication event no-response action authorize vlan 40 authentication host-mode multi-host authentication priority dot1x mab authentication port-control auto authentication timer reauthenticate 10 authentication timer inactivity 20 authentication violation protect mab dot1x pae authenticator dot1x timeout quiet-period 5 dot1x timeout tx-period 5 dot1x max-req 3 spanning-tree portfast

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved