I have an AC 3.0 connection that works fine prior to CSD. Once I've enabled CSD I get CSD to load and then the AC tunnel fails. Ive attached the DART bundle and a few screen shots.
View 3 RepliesWe are using a 5510 and have issues trying to use VPN with full tunnel to connect from inside the firewall to a customer site. I don't seem to have a problem when using split tunnel profiles. How would you troubleshoot this?
View 12 Replies View RelatedI need to work with the full tunnel feature of the IOS SSL VPN using a Cisco 1841. Here is what I see...
-I login to the portal page and click the "Start" button for "Tunnel Connection (SVC)"
-Security Alert message "This page requires a secure connection which includes server authentication. The Certificate Issuer for this site is untrusted or unknown. Do you wish to proceed?" I click yes.
-Anyconnect says "Please wait while VPN connection is established"
-Anyconnect error "The certificate on the secure gateway is invalid. The VPN connect will not establish"
I have ip phones at the remote location that connect into the phone switch(it's a nortel cs1000 system) over the tunnel. Internal calls work just fine, however when somebody calls from the outside, or calls are made to the outside the connection is never finalized. Like if I call from my cell it rings the phones, but when I answer there is nothing but dead air.In the group policy for the tunnel, I gave the remote site FULL access to the phones vlan and vice versa...which obviously works since internal calls work fine. If I remove my group policy and give it the Default group policy which essentially gives that tunnel full access to everything since the tunnel is set to bypass interface ACLS, external calls work fine. So it's definitely related to the group policy.
The group policy is basicallyAllow remote site to X network/host on these ports no denies since it blocks whatever isn't specifically allowed. However since it can get the phone switch and it can get to the internet I'm not seeing why the calls aren't working.The only thing I can think of to try doing as well is remove the allow inbound traffic to bypass interface rules and treat it just like another vlan interface on the ASA. Create the rules on each interface for the remote site network etc and see if it works that way.
We have ASA 5540. We setup Site-to-Site VPN and Remote Access VPN (Cisco VPN client). If are running full tunnel on the Cisco VPN client, the internet access is slow. For example, when we are running full-tunnel, the internet speed is 16 Mbps based on Speedtest.net. When we go to Speedtest.net, some of the graphics do not load. If we are running Split-tunnel, the internet access speed is 78 Mbps based on Speedtest.net and the Speedtest.net web site loads all the graphics.
View 6 Replies View RelatedA group of Citrix Clients connect to a Citrix Metaframe Server. The port numbers involved are Citrix Metaframe (TCP/UDP 1494) and MS Terminal Server (TCP/UDP 1604).
The network is configured such that the communication between the Citrix clients and server goes through a GRE tunnel. Traceroutes from client to server, and vice versa, confirm that it passes thru the GRE tunnel. There's no ACL, firewalls or NAT devices along the IP path, in both directions.
The issue is, all Citrix clients can ping to the server but some fail to log on to the server; some have no problem. Also, other applications, e.g. PCAnywhere, can go through. If the GRE tunnel is taken away, all Citrix clients can log on to the Citrix server.
I upgraded an ASA 5505 from 8.3(2) to 8.4(4) this evening. The 5505 is a backup and used to perform testing prior to production changes. After the upgrade was complete, a VPN tunnel began to fail. I did a limited search online to see if this was a known issue or something new. I also reviewed the release notes but did not see anything that matched the issue I received.
My concern is that this tunnel configuration is scheduled to be deployed to the production firewalls next week after their upgrade. But if it failed on the upgraded test unit, it may fail on the production units.
I downgraded the backup unit to 8.3(1) and verified that the tunnel indeed worked at that level.
I'm using a RV082 with latest firmware v4.0.4.02tm in one of our branch offices. Sometimes the tunnel to the main office (IPCOP 1.4.21) fails.
Both sides display the status "tunnel connected" but IP traffic doesn't go through. If i try to ping the main office using the RV082 diagnostic feature, the RV082 seems to run into a loop...the window continues refreshing without any error message and i'm not able to cancel the test. If I restart the RV082 using the web interface, the "diagnose" and VPN problem still exists, even if the web interface told me that the device did a restart.
The only solution is to to a cold restart of the RV082. After that, the VPN tunnel works again....
This problem occurred 3 times in the last 3 weeks. I never hat this problem with previous firmware versions at this ot other sites.
When my ASA5505 starts it loads into rommon. I enter "boot" and everything boots fine. How do I make that load by default whenever it starts. Any correct command syntax to make that happen ?
View 0 Replies View RelatedMy first time attempting this so excuse my wrong use of terms..i believe its load balancing...new company site is going to have 2 separate connections:
con 1: 15 up/2 down coax connection
con 2: 6 up/ 6 down dish
con 1 needs to simply have http and https traffic.
con 2 will have security surveillance, SNMP, and VoIP (PBX)
the hardware i know that will be at that location when i fly up there is a Sonicwall TZ210 and a 48-port Netgear gigabit...where do i start?
After configuring the router and enabling a load of functions to secure our LAN, the download speed halved! Even disabling AcitveX "eats" 10Mbs! I understand that enabling IPsec will drag the speed down to 25Mbps, but I have disabled this.
Even setting the QoS to speeds equal or higher then the ISP's promissises drags the speed down!
So I recently got a new computer today and it won't let me use my 100mbps of internet bandwidth. (Asus Sabertooth Z77 with an Intel 82579v gigabit lan controller) I noticed that at the LAN connection properties>Properties>Configure>Link Speed tab the 'Speed and Duplex' option was on Auto Negotiation and it was only accepting (or supporting) the 10mbps Full Duplex. When I switched it to 100mbps Full Duplex it would mark my connection icon with a red cross and when I clicked diagnose it said "Please connect your ethernet cable or your cable might be broken". So I tested my internet speed with that same cable on a different computer (laptop) and it worked with 40Mbps, so I don't think the cable is broken. Also I just recently downloaded some drivers but one was specifically for the Intel LAN controller but I'm a total noob for all of this computer stuff I don't know if it messed it up or something. Is it the motherboard that's not working correctly?
View 3 Replies View RelatedI'm standing beside my wireless access point with my laptop. It shows full signal in my laptop but I cannot connect to internet. I clicked on the view available networks and then the SSID names, typed my network key, and clicked "connect". It keeps on connecting, connecting and finally disappears and WAN connection remains with crossed mark. But it shows full signal in laptop and I'm standing beside the WAP.
View 4 Replies View RelatedLenovo T61P
Win 7
Wireless Connection (Router Linksys WRT54G2)
I installed Comodo's Firewall and during installation I accepted to install the Secure DNS too. Afterward I noticed my web-pages loaded slower than usual. They weren't extremely slow but definitely slower than what I've been accustomed. I tried some OPENDNS servers and others to see if it made any difference but it didn't. I also went to my router's setup page((http://192.168.1.1/)so I could manually add the previously mentioned DNS servers. I finally decided to revert back to my old DNS list. To disable using the Comodo DNS servers I did the following:Wireless Network Connection Properties-> Internet Protocol Ver 4 (TCP/IPv4)-> Properties -> Select "Obtain DNS server address automatically"I also went into to my router's setup page (http://192.168.1.1/) to set my DNS list to zeros so that I can get back my default ISP's DNS servers (207.69.188.185,186,187). However, website loading is still sluggish.I thought the issue might just be a temporary hiccup from my ISP but my roommate doesn't have these issues. We tried a speed test at dslreports.com and the results were weird. On my laptop the results were 8500+ Kb/s with a 279ms latency. I was 10 ft away from my router.
my internet speed is fast but page loads very slow
View 1 Replies View RelatedMy laptop is reading a full WiFi signal from my router. I am currently connected to the router via Ethernet on the same laptop. I've been reading tons of old threads to troubleshoot this. I'm at a loss. I have used this current networking hardware for more than a year without any problems. I do have a pretty old router but my iPod connects to the WiFi no problem at the moment. Here's what I've tried so far:
- soft reset of router
- power cycle modem and router
- removed saved network information from the laptop
[Code]......
I have Virgin Media XXL broadband in the UK. I have Avast antivirus. Windows firewall is enabled and all security updates are up to date. I have a 50mbit virgin fiber optic broadband which is working fine on my flatmate's pc's. While making sure the internet wasn't being used my speedtest still returned around 1mbit with full signal strength. I have run speedtest on 3 pc's at the same time and 2 of them were over 30mbit while mine was still barely 1mbit. I am using an Edimax EW-7811Un nano usb adapter. From reviews I read that it should work great with Virgin. But for some reason it doesn't work well despite the full signal strength.
View 7 Replies View RelatedI have 100 mbps fiber connection. I bought 320N today I bought 320N and here is the problem:
We have a switch in the building. I am getting connection via CAT5. So I choosed "Use as WAN Port" from Ethernet settings. There is not much you can do here. I just used PPPoE and connected internet without any problem. The problem is I am only getting 32mbps. When I connect CAT5 cable directly to my computer I am getting 92mbps.
Maybe WAG320N is not establishing a full duplex connection.
I am running a Cisco 878-K9 Router, IOS 12.4(11)T1, as a Firewall with EasyVPNServer. The VPN Server was created with the wizard from the SDM.Everything works fine, BUT the VPN connections fail after about 10 minutes.
View 1 Replies View RelatedI've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
I have set this "Black Friday" printer up and it shows it is transmitting wireless. However, I cannot get my PC to find it! I have tried everything I know. I am not an expert but is there something in my Verizon router that might be preventing it? I don't know what else it could be but maybe there is an expert out there that can.
View 5 Replies View RelatedI cant get this damn thing to connect to the internet (att dsl modem). I have ran the installation cd mulitple times and also configured it using the http. If i reset it while everything is hooked up and it makes an internet connection using DCHP (I think its called), but i need a PPPoE connection.
It seems to change my password (the username one that access the modem). The way i know is it always has more characters that the one i was provided by my isp with (*****). I dont enter any information other than my username or password (IP is dynamic).
I have a westell F90-6100 as my modem.
i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
View 1 Replies View RelatedI have a CISCO RV 120W router. I have set it up with a static IP address from Verizon. Internet can be accessed.I just want IPSec passthrough for some people who can connect with Nortel contivity client to the company RSA server. I can make only one connection. The second connection fails with 'banner text' response issues. One connection always works. The router has the latest firmware. I have enabled IPsec passthru.
View 1 Replies View Relatedproblem with my Dell Latitude D600 Laptop,I tried re-installing my OS, so now with a fresh new OS the wireless capabilities worked fine, but only for the first day, then the next morning the whole problem began again. Now it would say " No supported wireless adapters found" and when i would open the device manager some devices would have the yellow exclamation point, some of the devices would say "Intel PCIC compatible PCMICA controller" and " PCMICA MTD-0002" or just "card bus controller" and many other ones that would alternate when they appear. And also sometimes my network adapters would completely disappear from the list. I also tried scanning my whole drive for viruses and nothing was found.
Then i found that if you disconnect the wireless adapter physically and re connect it, it might work, but it didn't. I should also add that before this problem for some time i had another problem with the same laptop that had to do with the battery malfunctioning, and it displays a 4 orange , 1 green pattern sequence on the LED charge display. But it had never affected any of the laptops hardware or software before, so I don't know if that might have anything to do with it.
[code]...
When I start my laptop, an Acer 7715Z, it will try to connect to the internet, but often fails.I then try it a few times manually. But the first 5 minutes I can try as often as I like but it will give a 'problem' popup, offering me a windows troubleshooter (which doesn't find the problem).I just have to try manually over and over again until it finally connects.Then my problems are over and I can internet without loosing connection. This doesn't only happen at home, but also when I'm at relatives. So my modem or ISP is not the problem. Also, my other equipment works just fine (mac, iphone, ipod, netbook).I've updated the Broadcom 802.11n adapter driver, run a virus/malware check, etc. but nothing works.The wireless lan adapter I assume basically works ok as it doesn't loose connection once I get online? Is there another setting I could check or optimise? I find it so strange. It's like the first 20-30 times trying to manually connect something is blocking it and once I get through I'm online without problems or losing connection. As I mentioned earlier, my other equipment go online almost immediately. Is there some windows setting that could block my manual attempts for a few times before letting me in? Could the broadcom adapter be faulty after all, even when after connecting it stays connected and problem free? Any control panel or other setting I could check first before sending it to be checked/repaired?
View 6 Replies View RelatedI'm running Windows 7. As stated in the title, once I see the screen blink, I know I have a few moments of connectivity left. The screen will continue to blink, then the wireless network connection icon goes red with an "x" through it. The computer continues to work (albeit with the screen blinking), but with no connection to the Internet. Checking Device Manager indicates no conflicts. Manually pressing the "wireless connectivity button" on this Compaq, which shows green=connected, only turns it red for a second, then back to green as if the adapter is enabled. Doing this prior to the blink-failure cuts the wireless connection as it should. I added iTunes about a month ago, the problem started about two weeks ago.
View 2 Replies View RelatedWe are using an ASA with 8.4 in transparent mode. Connection fails when a host on inside tries to connect to a server on outside. This server uses mac-address 0100.5E00.0000 to load balance but replies with real mac-address.Firewall logs "Deny TCP".ARP inspection is disabled.
View 2 Replies View RelatedMy PC Info: Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5850 @ 2.16GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3069 Mb
Graphics Card: ATI Mobility Radeon HD 3450 , 256 Mb
Hard Drives: C: Total - 305242 MB, Free - 252510 MB;
Motherboard: Dell Inc., 0F700C, , .8QQVVG1.CN4864388L1948.
Antivirus: Norton Security Suite, Disabled
So I am having issues connecting to the internet. I can connect during safe mode but not on normal boot. I ran a diagnostic and it said that the IP Gateway failed. I read a previous post and did the command promp "ipconfig/all" and this is what it said:
Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersEbony>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ebony-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....
I have norton, and have recently run Malwarbytes, Microsoft Malicious Removal Tool, and Dell PC Tune Up
I can't seem to skype or video chat of any sort (ie: aim video chat, facebook video chat, etc.) on my computer. Whenever I start skype or try to start a video chat on aim/facebook, it fails and my internet disconnects for everyone. I don't know what could be wrong. Using the same wireless internet, my friends are able to video chat on their macbooks. It seems like my computer is the only one that can't video chat. Video chatting works when I use a sprint internet card. I have a sony vaio laptop running on windows 7. Our router in our apartment at school is a D-link wireless N? In addition to this problem, my internet loves to disconnect randomly too...this problem also persists at home with my Cisco Linksys router (model WRT160N V3) and Speedstream 5100 modem.
View 5 Replies View RelatedI have a E4200 V1 with firmware 1.0.0.5 installed The problem is that when I connect the cable from my modem to my router and recycle both I get a rapidly fashing Cisco light and can not connect to the internet.If I remove that cable and recycle the router my network works but (obviously) I have no internet connectivity.This was working (almost 2 years) without issue until today.I updated the firmware and did a factory reset and neither resolved the issue.My next experiment is to see if I can't get log files (since the factory reset) but I can't do that at this time.
View 3 Replies View RelatedI purchased and installed the above router to replace a working router that had a problem with our new condo location. The old router couldn't access one of our computers. The EA 3500 worked seamlessly for 6 months. Now the connection fails intermittently (more times off than on) from that one computer. It is two rooms over from the router & modem. These are now in a fixed location that cannot be moved.
View 7 Replies View Relatedwe are using Cisco VPN client to access our corporate network.I have 5 new notebooks Dell Latitude E6410 OS Windows 7 Professional x64, with identical hardware configuration.I downloaded Cisco VPN Client 5.0.07.440 (64 bit) and installed it on all notebooks. It works fine on 3 notebooks, while on 2 notebooks the VPN connection fails with error:
Secure VPN collection terminated locally by the client.
Reason 403: Unable to contact the security gateway
We use a smartcard for VPN access (etoken from Aladdin)
Here an extract from Cisco log:
Cisco Systems VPN Client Version 5.0.07.0440Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.Client Type(s): Windows, WinNTRunning on: 6.1.7600...Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600026 Attempting to find a Certificate using Serial Hash....Sev=Info/6 CERT/0x63600027 Found a Certificate using Serial Hash....Sev=Info/4 CERT/0x63600015 Cert (cn=<omissis>,ou=Remote,ou=Users,ou=<omissis>,dc=it,dc=<omissis>,dc=local) verification succeeded....Sev=Info/4 CM/0x63100002 Begin connection process...Sev=Info/4 CM/0x63100004 Establish secure connection...Sev=Info/4
[code]......
It seems the problem is in the certificate, but I verified and Cisco client says it's ok. It's also the only valid certificate in MMC->Certificates->Personal.Furthermore, also using other smartcard (etokens) of other users it doesn't work.