I've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
I Have RV220W Rev 1.0.3.5/I want to create 5 users adn connect remotely to the office network using a PPTP connection.
I have enabled the PPTP server and created users.From a remote location (WAN) on Windows 7, I have created a PPTP connection and I can connect however I can not ping or map to the office network.
I have the RV220W and we are mainly using PPTP for VPN access. I can not add more than 9 PPTP VPN user acounts. When I go to add a tenth account the interface just hangs and stops responding. I can delete a user and then add another user and this works fine. I can also add other types of VPN users.
I currently have a RV220W connected over PPTP to the internet. I want to connect with an RV042 with a fixed IP Address.The connection is working, but I always have to add a static route to the remote IP-Adress that I can transmit data.Since my own IP Adress is a dynamic one that changes every day I have to enter every day in the static route as gateway adress the new WAN IP Address.
I possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.
I have two offices connected with an IPSEC VPN tunnel using RV220W routers. The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x). I have also set up PPTP users for remote access. PPTP users that connect to site 1 cannot access site 2 and vice versa. The PPTP users have no trouble accessing the resources on the site that they connect to. I have tried activating RIP and adding various static routes with no success. If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.
I've previously upgraded the firmware on our RV220W from 1.0.0.26 to 1.0.1.0 without any problems but all attempts to upgrade to the latest version 1.0.2.4 fails with the following message "Upgrade failed due to invalid/corrupted firmware". The router then automatically reboots with the current firmware.
We've already tried re-downloading and applying the update from several different machines using different operating systems and browsers without success. How to apply this firmware version successfully? We really need one of the VLAN fixes included in this latest version!
I am having problem when try to connect through VPN from MacOS to my RV016 router.The situation is like this. I can connect to the router,the connection is succesfull, but when I try access resources inside the network it disconnects me.The message is "You are dissconnected by the PPTP Server". I encountered this problem on MacOS Snow Leopard and Lion. I tried to connect from 3 different Apple machines, but the problem is the same.
I am working with a RV180w and need to map drives from the internal network to the VPN client but whenever I try to connect to a shared drive I continue to get authentication messages from the DC. Any useful guide for configuration in this scenario. Internal subnet is on Windows 2008 domain.
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0) Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
We bought a RV220W in order to get a VPN in our Small Business. The RV220W will only be used to let clients connect to it and not a tunnel between another VPN box.We could use QuickVPN, but it won't be working in our case, because in order to use QuickVPN, the router wants to change its IP 10.x.y.1. Because we have multiple servers/services that are using a static IP, it would be quite painful to change the subnet. Therefore, we would like to stay on the same subnet and change it in worst case scenario only. This is why QuickVPN is not an option here.We could use SSL VPN, but most of our clients who will connect to the VPN are using Windows 7 x64. I have tried the Windows 7 x64 fix told in the latest firmware release notes, but I can't get it to work on my computer, which is a Win7 x64. It might still be broken. Many of them are not very tech-savyy, so I can't tell them to use a virtual machine to connect.We want a secure connection, therefore IPSec is better than PPTP. I've been trying to setup IPSec for the past hours but I can't get it working. At first, I wanted to use an SSL certificate, but having no luck with this, I switched to a Pre-shared Key (PSK) in order to get things simpler. Eventually I would like to use an SSL certificate, however I would like to get PSK working first to confirm that the IPSec connection is working.
I have attached with this post, screenshots of the IKE and VPN Policies. I have used the VPN Wizard in order to complete these fields. The local identifier is the WAN DynDNS FQDN. However, as for the remote FQDN, there should be none really, because clients are connecting to it, so the RV220W won't know in advance who's connecting and from where. I have read that when using the Responder type, the remote settings should not matter. Also, the PSK is 25 caracters long.After setting the RV220W up, I have set up a L2TP/IPSec VPN connection on my Windows 7. I have set up the connection to connect to the DynDNS address and set up the PSK in the Advanced settings. After I typed my IPSec username and password to connect (which was created in the IPSec users section), Windows tries to connect and times out :
Error 789 : The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer.
At the same time on the RV220W, this error shows up in the logs :
2012-08-26 23:45:24: [rv220w][IKE] ERROR: Could not find configuration for 24.54.xx.xx[500]
I can't figure out what I am doing wrong. I've read the Administration manual quite a few times and it seems that I have followed everything by the book.I have tried to enable/disable my Windows firewall, but did not get any luck. The RV220W is located at a remote office, to make sure that I can connect from the outside, before you think that I'm trying to connect to the outside, from the inside I have changed few settings in the IKE policy to try to make it work. Settings such as the Exchange Mode, because I've read that the Aggressive mode had issues. At this moment, the settings are back to default, once the wizard has been run. I'm thinking about setting a PPTP to confirm that this works, then move up to IPSec PSK, then to IPSec SSL Certificate.
I installed the RV220W Router in my office about 2 weeks ago and everything works perfectly for 3-4 days but then my connection drops out and the router must be restarted to restore connectivity. When I say the connection drops basically the internet connection drops out and my network connections drop shortly thereafter. Usually the wireless connections lose connectivity followed within a few minutes by the wired connections.
Is there something in my firewall settings that could cause this issue? I have checked with my ISP to verify there are no problems on their end.
I'm on firmware 1.0.0.26 and I'm seeing frequent drops in the WAN connection. Most network clients don't notice the drop because it reconnects, but the X11 windows server running over a VPN drops the session and I have to re-establish it. Also, at the same time I experience a 15-20 second silence gap on my VoIP phone connected to vonage (not over VPN). Never happened on my Linksys router, but it happens many times a day on the rv220w. When the drop happens I get the errors listed below in the router log:
I am not able to establish a PTPP connection with my iPhone over WAN. When I am in my local Wireless LAN it works nice using the external FQDN of the RV220W. But when I test the VPN access over 3G (meaning I am coming in over the WAN port) I get and error message that the connection to the PPP server could not be established.
Some more Info
- Running latest firmware - Port 1723 is open to the Internet - ISP doesn't filter anything - No Firewall settings blocking anything at the moment - Nothing in the logs indicating what the problem is
So what needs to be done here to get it running over the WAN port and not only over the LAN ports?
My RV220W is sitting behind a Dynalink RTA1046VW ADSL Modem.
Can't get the RV220W to detect an internet connection through the WAN port. Have got the PPPoE profile set up etc. Have tried the Dynalink in bridging mode, but to no success. Tried the setup wizard.
Firmware is current: v1.0.2.4. The connection is picked up ok through the ethernet ports.
I'm wondering if it's possible to setup SSL VPN connection via OPEN VPN client?I'm a Mac OS 1.7 user with Tunnelblick.
I tried to use "built-in" SSL VPN Tunnel client but unfortunately it's not working - during installation Java exception appears saying that either I don't have admin privileges or there is not enough space.. Of course I'm admin and there is plenty of space...
I'd like to enable client to router VPN connections. I have a question how to make any sucessful VPN connection to RV220W. From all the tests I made only SSL VPN on Windows XP x86 client machine was working.
For IPSec VPN I always receive this message: [rv220w][IKE] ERROR: Could not find configuration for XXX.XXX.XXX.XXX[500]. I tried with windows and shrewsoft vpn client.
Can't make SSL VPN to work in Windows 7 x64 client because the drivers are not digitally signed. It only works in Windows XP x86 but this is not acceptable. I need universal solution for win clients.
I also need working solution for Android Phone? Router firmware 1.0.3.5. I also tried this step by step guide. No go.
I have a CISCO RV220W Wireless router, running the latest firmware (1.0.1.0) and CISCO's AnyConnect Secure Mobility Client v3.0.2052, and Windows 7, 64 bit. My laptop is a corporate based work laptop, and I am trying to use it to connect to my home network ( CISCO RV 220W ).
When I try to connect my PC via the wireless network (to the CISCO Router), via CISCO's AnyConnect Secure Mobility Client, the WiFi connection never actually takes place - rather the CISCO AnyConnect Secure Mobility Client s/w interface suggests that it is "associating" and seems to go into an endless loop. It never receives a DHCP address from the CISCO router. ( see attached picture ).
If I disable the "Cisco AnyConnect Network Access Manager" service, as well as the "Cisco AnyConnect Network Access Manager Logon Module" service within Windows 7, I have no problems establishing a WiFi network with my CISCO router via the traditional Windows approach of connecting to a WiFi network. The inability to connect wirelessly comes back, when these services are re-enabled. It appears to me (a layman) as if the "Network Access Manager" layer is preventing connection to the CISCO router via WiFi.
I have no problems connecting to the CISCO router using CISCO AnyConnect Secure Mobile client over a physical Ethernet cable. I also have a Belkin branded Wireless router that works perfectly with the CISCO AnyConnect Secure Mobility Client. All of the wireless settings on the CISCO RV220W router are factory default.
how I can get the CISCO AnyConnect Secure Mobility Client to play nicely with the CISCO Router when I wish to establish a WiFi connection?
I have also attached the Windows based Event Log associated with this trouble shooting - associated with the "Network Access Manager" logging. SSID C&C@Home is the CISCO Router, whilst SSID Cam@Home is the Belkin wireless router.
I was wondering if anyone has seen their VPN User Connection Status Table empty even though you know for sure clients are connected? I connect with my iPhone to the PPTP VPN successfully and it works fine but there's no entry for the connection on the VPN User Connection Status Table. Is that normal? Does the router only collect data about Windows clients?
We have RV220W at corporate office...intent is to have (5) groups of (3) users each connecting via VPN. Had assumed would be using QuickVPN and have set up users, etc and connections at current locations are quick, smooth, reliable. I have set up (2) locations (6 users so far). However, after 4th connection (no matter where or in what order) client hangs at "Verifying Network" and doesn't complete connection. So, I have unique usernames, etc but each of the (3) at a location are hitting the router with the same IP. Is this the problem? I'm sure the RV220W can handle 15 simultaneous connections, but can the router deal with (3) connections from the same external IP?
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
an RVS4000 shall establish a pptp VPN connection. The router is connected trough its WAN port to the first router which connects to the internet.
The PPTP VPN connection cannot be established but the pptp server can be pinged from the VPN router. Login data and password is OK. Connection can be established from a win7 computer without any problem.
We have a Cisco 891 with this configuration belowI got several computer on my lan that needs to connect to an external Windows server with pptp. The windows server is not mine but it works. The clients are using the windows connection manager. We can connect to the windows pptp server for hours sometimes.But, sometimes we can just connect about 3-4-5 minutes, and it auto-disconnects. Is there something wrong in my configuration ? I heard the cisco router is messing with the keepalive or the connection state.It seems to happens when i have more than 5-6 clients connected at the same time on the same server. I got theses mesages : Link to VPN failed. OR ERROR 619 OR ERROR 651Before, I had a RV042 and it worked like a charm. We were 10 on the vpn server and it was working. I dont see why Its not working now.
version 15.0no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname Quantis891!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication login local_authen localaaa authorization exec local_author local !!!!!aaa session-id common!!!clock timezone PCTime -5clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00!!!no ip source-route!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 10.1.1.201 10.1.1.254! [Code] .....
