I am working with a RV180w and need to map drives from the internal network to the VPN client but whenever I try to connect to a shared drive I continue to get authentication messages from the DC. Any useful guide for configuration in this scenario. Internal subnet is on Windows 2008 domain.
View 1 Replies
I am having a problem connecting to my office VPN from home since I changed my (home) router to the RV180W. I am not using pre-configured tunnels, I just connect to the office VPN using the built-in Windows PPTP client when necessary. I have a small network at home using the router in a NAT configuration on my static IP fibre DSL connection.
I had previously been able to connect using PPTP from either XP or Windows 7. Now I get "Error 732: Your computer and the remote computer could not agree on PPP control protocols". Unfortunately I don't know what hardware or PPTP server is used at the office.(I don't know if it is relevant but I have also configured the RV180 PPTP server to allow incoming VPN connections - this works fine. It doesn't make any difference to my issue whether it is enabled or not.)Are there any known problems using Windows PPTP client through the router in a NAT configuration. Is there anything I need to configure apart from enabling PPTP passthrough?
Edit: Just to clarify, the problem is making PPTP VPN connections from XP/Win7 on my home network over the internet to my office VPN/PPTP server, via the RV180W as my home router (using NAT/PAT).
Edit: More info. Looks like the office VPN is a Microsoft RAS server on Windows 2008 behind a cisco PIX firewall.
Edit: Just to be sure, I swapped out the cisco RV180W for my old netgear router and I was immediately able to VPN again with no issue from both XP and Win7. When I swapped the RV180W back in again, I was able to VPN from XP but not Win 7 so it looks as though the PPTP passthrough works occasionally but is intermittent. Just to be clear, the VPN is only intermittent using the RV180, it has always worked flawlessly on the other router so I don't think there is a problem with the internet connection or client/server configuration.
I have tried to make a VPN connection between RV180W and iPad with PPTP. I have enabled the server, set the address range, added and user and enabled it.
I entered the same information into iPad but when I try to start the VPN, iPad just tried to make connection and finally fails with an error stating that PPP server cannot be reached.
I think the devices are able to make some kind of connection as if I change the gateway IP address incorrect, I get a different kind of error message. I also tried to reboot the router...
I'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION:
IKE Policy Configuration:
VPN Policy Configuration:
CLIENT CONFIGURATION:
[code]....
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies View RelatedI've read and read about setting up the WAN static IP connection, and can't get it to work. I purchased this router to replace an older Linksys Router (WRT150N) so that I could better implement VPN. All I need is 2 remote connections. The Linksys Router has been working great with a static IP setting, so I figured all I need to do to is enter the same IP, subnet, gateway, and DNS settings in the RV180W and it should work fine. Well it doesn't provide any connection to the internet. As far as I can see, it has all the same settings set that the linksys has.
Is there something additional I must do for a WAN static IP setting setup. I even contacted the ISP but they say their modem is fine and of-course they won't assist with the router. As soon as I connect the linksys back to the modem, I get access to the internet.
I'm no engineer, but something isn't allowing any Internet services. LAN is fine. I attached a W7 laptop to the router, and it says it can't reach the internet due to something about proxy services. There is no proxy server so not sure what it is referring to.
By the way I tried another manufacturer router just to ensure that it wasn't a defective RV180W, but that router didn't connect either - same issue. If I set it up on my home service, both work albeit only with DHCP WAN settings.
I am having problem when try to connect through VPN from MacOS to my RV016 router.The situation is like this. I can connect to the router,the connection is succesfull, but when I try access resources inside the network it disconnects me.The message is "You are dissconnected by the PPTP Server". I encountered this problem on MacOS Snow Leopard and Lion. I tried to connect from 3 different Apple machines, but the problem is the same.
View 1 Replies View RelatedI've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies View RelatedUntil now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies View Relatedi'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
View 1 Replies View RelatedMy network consists of the following:
Office-RV042 with static IP ->SBS2003 (10.10.10.5/ 255.255.255.0)
Remote: BEFSR41 with Dynamic -> XP sp3 VPN client (192.168.3.x/ 255.255.255.248)
Within the RV042 I have enabled the PPtP server and assigned a user. No port forwarding enabled. All VPN passthroughs and firewall is enabled. DHCP server is disabled.I can establish a connection to the rv042 and ping PCs including the sbs domain server on the office side but am unable to browse any folders. When I attempt to access a network folder located on the office server I am prompted for a username/ password. Upon entering my domain credentials I get an error stating: "the user name you typed is the same user name you logged in with. That user name has already been tried. A domain controller cannot be found to verify that user name"
I have a Cisco SRP527W at my remote office set up. I have configered a VPN connection to it. I installed Cisco VPN Client on my laptop.I can connect to the VPN but can not access the shared folders. I can ping the PC that has the shared folders. I take my PC and connect to the onsite LAN with WIFI, and I can now view the shared folders. I assume it must be somthing in the VPN set up that is blocking the shared folders from being seen. I also have disconnect all firewalls during testing at the remote end. I'am using windows 7 (64) on both PC's.
View 6 Replies View RelatedCan I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies View Related in my tv room i have a modem and router. this is wired to my basement wan router, on the other side of the house. connected to basement router is a pc with a shared drive. so for example.
MODEM>
WAN ROUTER> hardwired tv computer
WAN BASEMENT ROUTER> big ol hdd on main computer.
I need BOTH routers active for wireless coverage, I use only wifi calling for my phone service.so how can i share the 'big ol hdd' to my 'tv computer' without altering much on my network, if anything. i use my current setup for work and i have multiple servers running all the time.
I have several drives that are accessed through a LAN but as soon as I connet to another drive through VPN all the drives get disconnected. According to the IT people this is a feature of VPN for security reasons and there is no way to access those drives.Anyone knows if there is a way to connect to the VPN drive and the local LAN drives without getting the LAN drives disconnected?
View 8 Replies View RelatedI installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
View 4 Replies View RelatedWe have installed a fiber internet access and have the ONT from the provider already installed.We're trying to use the RV180W to use this internet connection. [code] So I need to configure the router with the .36 static IP on the WAN, and using the .37 gateway and the provided DNS servers. I also need that this WAN is tagged with VLAN ID 20. I'm only able to set VLAN ID on the LAN ports via the admin interface.
View 8 Replies View RelatedI am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
i've installed the new firmware on my router and now the UC is showing 100% all the time. I've tried to factory reset it, it's doing the same thing. If I downgrade to previous firmware, it goes back to normal . I've only 1 PC in my network (test lab), so no big traffic here. is it a bug ?
View 1 Replies View RelatedSeagate GoFlex Home External Hardrive.does not download drives x y z
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View Relatedhow to open shared drives on server 2008 while connecting with vpn connection
View 1 Replies View RelatedI just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
View 5 Replies View Relatedwe've changed our rv042 for a rv180w and now when I try to upload files to my ftp server (vsftpd under centos) it get stuck at 100%.I've changed my ftp server to proftpd instead of vsftpd and everything's ok.but vsftpd isn't the problem since i was able to upload with my rv042 without any problems.so i guess there's a problem with the rv180w security.i've already disable stealth mode and it's doing the same thing when i try to upload to the same server but through the vpn tunnel, everything's ok.So it's really in the rv180w lan->wan routing
View 10 Replies View RelatedHave not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN logins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download.
Does buying RV180W allow download of Cisco Systems VPN Client software ?
I am located in UK which uses PPoA for ADSL broadband. I use a DrayTek Vigor120 ADSL2 Modem to act as an ADSL bridge and PPoA to PPPoE converter. This passes the ADSL authentication requirement (and subsequent single static IP address) to the Cisco Small Business RV180W sitting behind the Draytek. However, the RV180 (Firmware Version 1.0.0.30) cannot form the PPPoE connection. I have tested the modem, adsl username and password by creating a PPPoE interface on my computer and connecting this directly to the Draytek modem. The computer receives the expected IP address and I can ping remote public IPs. I have entered the username and password into the PPPoE profile,
Authentication type: CHAP (confirmed by ISP but I have also tried all other options just in case).
Connection Type: Keep Connected.
MTU Size: 1400 (also tried default, which worked OK on computer interface).
MAC Address Source: Use Default (I have successfully used combined modem/router so a "fixed" MAC address is not required).
I live in China. I want all of my PC's and devices to connect through the RV180W VPN Router to a VPN provider in the US so that all of my traffic is encrypted and appears to have a US IP address. I need to find a VPN Service Provider that supports the RV180W and how to configure it. I don't want to configure every PC and device, I just want them to use the VPN conneciton at the router.
View 3 Replies View RelatedI am using DynDNS in lieu of a static ip. My ISP changed my WAN ip last night as expected however the RV180W did not update the WAN ip, and so the router is now offline. Using a secondary internet connection I have logged into DynDNS.com and checked my hosts file and confirmed the ipa has not updated since March. I changed the update period from 360 to 2 so this never happens again, but I need to now change the WAN ipa in the RV180W to match the new one. I remember a screen that shows the current WAN ip address greyed out under the present one, but I dont recll where to go to get to that. I am at a loss as to where I go in the RV180W to change the WAN ip address.
View 1 Replies View RelatedWe are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum?
View 3 Replies View RelatedComcast has indicated that this is required for IPv6 to work, and since it means gatting a /64 address space for my network I am understandably eager to tak advantage of this new functionality when it is available in my area.
View 44 Replies View RelatedI am wanting to purchase the RV180W for a small Optometrist office. We are beginning our transition to EHR and what to ensure the RV180W is HIPAA compliant and if not what would be the next best product for about the same price?
View 2 Replies View RelatedI have rv180w (firmware 1.0.1.9) and 1 Gbit/s internet.When i turn on WAN Traffic meter, WAN speed down to 100mbit/s.I didn't find any suggestions in official documentation.Is this a bug or undocumented feature?
View 2 Replies View Related
