Cisco VPN :: Change Subnet Of A PPTP VPN On RV220W?
Feb 2, 2012How do I change the subnet of a PPTP VPN network on an RV220w?
View 1 Replies
ADVERTISEMENT
Cisco Routers :: RV220W PPTP Users Unable To Access Subnet Across Tunnel
Apr 21, 2012I have two offices connected with an IPSEC VPN tunnel using RV220W routers. The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x). I have also set up PPTP users for remote access. PPTP users that connect to site 1 cannot access site 2 and vice versa. The PPTP users have no trouble accessing the resources on the site that they connect to. I have tried activating RIP and adding various static routes with no success. If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.
View 2 Replies View RelatedCisco Routers :: Set Up PPTP VPN With RV220W
Jul 19, 2012I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedCisco Routers :: RV220W PPTP Not Working?
Mar 23, 2012I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
Cisco Routers :: PPTP VPN Client To RV220W?
Aug 8, 2012I Have RV220W Rev 1.0.3.5/I want to create 5 users adn connect remotely to the office network using a PPTP connection.
I have enabled the PPTP server and created users.From a remote location (WAN) on Windows 7, I have created a PPTP connection and I can connect however I can not ping or map to the office network.
Cisco Routers :: RV220W PPTP Users
Apr 2, 2012I need a name resolution within my pptp users. How do I configure the dns settings of a pptp user client.
View 4 Replies View RelatedCisco Routers :: RV220W Only Add 9 PPTP User Accounts
Jul 17, 2012I have the RV220W and we are mainly using PPTP for VPN access. I can not add more than 9 PPTP VPN user acounts. When I go to add a tenth account the interface just hangs and stops responding. I can delete a user and then add another user and this works fine. I can also add other types of VPN users.
View 4 Replies View RelatedCisco Routers :: PPTP Connection To RV220W Fails?
Jun 4, 2012I've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
Cisco Routers :: RV220W Connected Over PPTP To Internet And Site2Site VPN?
Oct 13, 2011I currently have a RV220W connected over PPTP to the internet. I want to connect with an RV042 with a fixed IP Address.The connection is working, but I always have to add a static route to the remote IP-Adress that I can transmit data.Since my own IP Adress is a dynamic one that changes every day I have to enter every day in the static route as gateway adress the new WAN IP Address.
View 4 Replies View RelatedCisco Routers :: RV220W Remote PPTP VPN Connection Fails?
Jan 23, 2012i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
View 1 Replies View RelatedCisco Routers :: RV220W Not Working With PPTP Server On One VLAN Only
May 5, 2012I possess a RV220W (firmware 1.0.3.5) but I can't seem to work with the PPTP server on one VLAN only.
My default VLAN is in 192.168.1.1/24. I created a VLAN ID 10 in 192.168.50.1/24 inter-vlan routing : disabled and Device Management : disabled. (Menu Networking > LAN > VLAN Membership and Multiple VLAN Subnets).
Then I configured a PPTP server on the IP range 192.168.50.200 to 192.168.50.210.
To finish I created my user. (Menu VPN > IPSEC > VPN Users).
The PPTP tunnel is working, but on all my local network and not only the VLAN ID 10.
Cisco Routers :: RV220W Can't Create 255.255.254.0 Subnet
Nov 8, 2012I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
Cisco Routers :: RV220W - Routing IPv6 Subnet
Feb 27, 2013I have a few questions regarding IPv6.
Question 1.
I have no idea how to route IPv6. My provider has provided me with a subnet. This subnet is for example 1:1:1::/48
The router of the provider is located at 1:1:1::1 and my router should get 1:1:1::2(Cisco router). Every subnet I want to create must be routed by 1:1:1::2, for example if I want to create 1:1:1:1111::/64 it needs to be routerd by 1:1:1::2
How do I configure this on the RV220w?
Question 2.
I have the possibility to create vlans on the RV220W. I can configure IPv4 addressen per vlan. Only for IPv6 this is not possible.How do I configure this or when will new software be released to configure this?Or do I have to edit the configuration file?
Change Subnet Mask 255.255.255.0 To 255.255.0.0?
Jan 28, 2011our subnet mask is 255.255.255.0....can I change it to something else like 255.255.0.0.
View 4 Replies View RelatedCisco Routers :: WRV210 Router - Can't Change Static WAN Subnet To 240
Sep 20, 2011In the Internet Setup area (WAN) when I change to Static IP I can't change the Subnet Mask from 255.255.255.0 to 255.255.255.240 which is the information currently in my D-Link router. When I try to save the changes I get the error "The IP address is not in the right subnet". I find it hard to believe that a lowly D-Link $35 router has nore capability then a Ciso Small Business Router.
View 1 Replies View RelatedCisco Routers :: After Password Change Can't Access RV220W?
Mar 30, 2013I have changed administrator password to a secure one, just after the changind the password it logged off and offered to login. Now when I put the same password it writes: Invalid password for Admin user Password I used: 8_^!-,Opc: 5Gj3v5<Xb06?9z\SeWr2z9axdPa-f+L:Wj]NzEF2>v!Fu&lS0 There were no warnings that some symbols are not allowed, etc.
How can I access my router? what should I remove from the password to get access?
Cisco Security :: Can Configure A PIX (515) As PPTP Client To Establish A Tunnel With PPTP Server
May 15, 2006Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
View 5 Replies View RelatedAdding A Subnet To A Switch On Different Subnet?
Aug 3, 2012What I am trying to do is I have one switch with say a 10.1.9.1 sub-net I need to have one of the ports to be trucked with two vlans one for DSL and the other for a local connection with the sub-net of 10.1.5.1 both of the sub-nets are configured in the core as 9 and 5 so I have port 0 set up as a trunk and it is set up as ge-0/0/0.0 vlan_5, vlan_192 on the 10.1.9.1 subnet switch. The DSL is working but the local is not pulling a 10.1.5.1 IP and has no connectivity. Everything looks as if it is configured correctly but still the DSl is working but not the Local connection.
View 2 Replies View RelatedCisco WAN :: 1723 - PPTP Over NAT NVI
Dec 20, 2010i have a user in LAN which needs access to remote PPTP server. My router uses NAT NVI for some reasons to provide internet access.
Problem is what tcp/1723 is NATed successfully and it appears what GRE traffic is NATed as well, but GRE packets are NOT passed back to user on LAN.
Config is that simple:
interface Fas4
ip address x.x.x.x x.x.x.x
ip nat enable
interface Vlan1
ip address 10.0.0.1 255.255.255.0
ip nat enable
ip access-list extended nat_clients
permit ip 10.0.0.0 0.0.0.255 any
ip nat source list nat_clients interface Fas4(code)
Cisco WAN :: RVS4000 - PPTP Connection Not Possible?
Dec 15, 2011an RVS4000 shall establish a pptp VPN connection. The router is connected trough its WAN port to the first router which connects to the internet.
The PPTP VPN connection cannot be established but the pptp server can be pinged from the VPN router. Login data and password is OK. Connection can be established from a win7 computer without any problem.
Cisco VPN :: 877 Encryption Not Working On PPTP VPN
Jul 2, 2011I have a Cisco 877 router and I configured it to act as a VPN server, supporting both PPTP and L2TP VPNs. I can succesfully connect to it from Windows computers using the built-in VPN software.There is only one problem: when using a PPTP VPN, encryption doesn't work. If I configure the client to require encryption (default setting), the connection fails with an error about the remote endpoint not supporting it. If I remove the encryption requirement, the connection succeeds. I've also tried tweaking the encryption settings (40/128 bits), but this didn't work either. [code]
The router's IOS version is 15, and it fully supports encryption. The strangest thing is, encryption is actually required in the router config; but not only the router doesn't seem to offer it... it also accepts unencrypted connections, which it shouldn't. It's like the ppp encrypt mppe auto required command is completely ignored.
Cisco VPN :: RVL200 As A PPTP Client
May 22, 2012I'm trying to set up a permanent VPN connection for an Expat. We've got an RV042 set up on site to act as the server, and an RVL200 as a client. This RVL200 will be behind a home router, so it needs to initiate the connection every time; the site side router won't be able to see it behind the Expat's home router.I've got a PPTP server set up on the RV042, and I'm trying to get the RVL200 to connect to it as a client. Is there any way to do so, or will we need to go with another option? Because on the RV042, I see no way to set up an SSL server of any kind; only a direct SSL Tunnel, which won't work as again, the RV042 will not be able to see the RVL200.
View 1 Replies View RelatedCisco VPN :: 892 And PPTP Clients Connection
Mar 6, 2011We have a Cisco 891 with this configuration belowI got several computer on my lan that needs to connect to an external Windows server with pptp. The windows server is not mine but it works. The clients are using the windows connection manager. We can connect to the windows pptp server for hours sometimes.But, sometimes we can just connect about 3-4-5 minutes, and it auto-disconnects. Is there something wrong in my configuration ? I heard the cisco router is messing with the keepalive or the connection state.It seems to happens when i have more than 5-6 clients connected at the same time on the same server. I got theses mesages : Link to VPN failed. OR ERROR 619 OR ERROR 651Before, I had a RV042 and it worked like a charm. We were 10 on the vpn server and it was working. I dont see why Its not working now.
version 15.0no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname Quantis891!boot-start-markerboot-end-marker!!aaa new-model!!aaa authentication login local_authen localaaa authorization exec local_author local !!!!!aaa session-id common!!!clock timezone PCTime -5clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00!!!no ip source-route!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 10.1.1.201 10.1.1.254!
[Code] .....
Cisco VPN :: PPTP Disappeared On 2901?
Jul 6, 2012I recently obtained a 2901 router running 15.2(2)T to replace my old 877 which was running 15.1(4)M1. The 2901 is humming along quite nicely but I have had difficulty configuring one feature which was working fine on the 877. The router needs to be a PPTP client to a hosted VPN service. On the 877, I had it configured like this: [code] I then had a dialer interface to actually set up the connection, and some PBR to control what went over the VPN. All well and good, and it worked fine. But on the 2901, when I try to configure the same thing, there is no such command as "protocol pptp" -- the only option is protocol l2tp.Was PPTP support deprecated somwhere between 15.1 and 15.2, or does the 2901 itself not support it for some reason? Obviously I understand that l2tp is superior to pptp, but at the moment this is my only option.
View 2 Replies View RelatedCisco VPN :: 871 PPTP VPN Server Setup
Mar 9, 2012I am trying to configure a Cisco 871 to act as a PPTP VPN server on my home network. I have referenced Cisco's documentation regarding this which I will include below as well as a copy of my current running configuration and terminal monitor information from when I attempt to establish a connection.
When I attempt to connect from a Windows machine I receive the following error: 'Error 807: The network connection between your computer and the VPN server was interrupted.' 'The remote device won't accept the connection.'When I attempt to connect VIA my mobile, I get 'The server has hung up'.The 871 does detect the incoming connection which can be seen from the terminal monitor output: url...
Cisco VPN :: 857w PPTP Client
May 19, 2012Looks like cisco 857w does not support pptp client in my IOS version, only l2tp is supported. Does there is some IOS version I can upgrade/downgrade to configure cisco as pptp client?
View 1 Replies View RelatedWindows 7 PPTP VPN Error 807 And 800?
Mar 21, 2011don't steer the topic from PPTP to IPsec and other types of VPN which is more secure than PPTP,,,,etc have got this scenario windows 7 is acting as vpn client at home and windows XP is acting as vpn server at workAt home (LAN address is 192.168.10.x/24)And I configured windows 7 as VPN client same as here [CODE]
View 6 Replies View RelatedCisco VPN :: Can 2651XM Be Configured As PPTP VPN Endpoint?
Oct 31, 2011Cisco 2651xm router
IOS: c2600-ipvoicek9-mz.124-15.T7.bin
Can a 2651XM router be configured as a PPTP VPN endpoint (client)? I ask because I want to connect this router to a professional vpn (privacy) service such as proxpn or mullvad or similar. If it can't, any vpn privacy services that cater for cisco-based vpn connection?
Cisco VPN :: Enable PPTP Passthrough ASA 5505
Apr 10, 2012How to enable PPTP passthrough on Cisco ASA 5505?I have a RRAS server inside and the client is trying to connect from outside.
View 1 Replies View RelatedCisco VPN :: ISR1921 PPTP VPN With Encrypted Password
Sep 19, 2011I am actualy trying to make a remote access VPN between a ISR1921 and Windows 7 pro. I already managed to put a PPTP VPN with an authentication against our LDAP databse via radius. But our password are in SHA1 in our LDAP, so I had to let the password unencrypted on the network using pap and this is bad.If I don't use pap, it simply doesn't work since all the other method need unencrypted password for the challenge authentication.Does that mean that every remote access VPN keep our password unencrypted ? Maybe use EAP (but I can't find a howto or good documentation about it)? Can I add a certificate or something?
View 1 Replies View RelatedCisco Firewall :: PPTP Traffic Cannot Pass Through PIX 525 7.0(7)
May 6, 2008i read cisco document:[URL] pptp client is in inside,pptp server is in outside.when i donot use firewall, the pptp connection can establish successfully.but use pix 525 7.0(7) i config:
inspect pptp.
pptp connection cannot setup.
show connection in pix:
pptp tcp 1723 is ok.
gre connection only one "E" flag, E means 'outside back connection'.i try second method:delete 'inspect pptp',permit tcp 1723 and gre traffic from outside to inside, and i have config static nat,but the pptp connection cannot work too.so i think there is a pptp bug exist in pix 7.0(7).
Cisco VPN :: ASA 8.2 How To Allow Access To External VPN Network Via PPTP
Jul 28, 2012We would like to have the ability to connect to a VPN of a business we recently acquired. When connecting to it directly from the Internet (no firewall), it is accessible. However, behind our firewall, there is no access. We are using Cisco ASA 8.2 (2).Currently, we have an entry as follows:
-object-group service PPTP tcp
-port-object eq pptp
access-list inside_access_in extended permit tcp any host object_name object-group PPTP. we want any device within our network to be able to access the VPN via PPTP.
Cisco VPN :: To Connect To Remote PPTP VPN Via PIX 515e
Feb 7, 2012A user in our office needs to connect to a client's remote PPTP VPN but can't connect. The user is running Windows 7. We have a Cisco PIX 515e firewall that is running PIX Version 6.3(3) - this is what our user is having to go through to try and make the connection to the client's remote VPN.
The client's network guys have come back and said the issue is at our side. They say that they can see some of our traffic but not all of it. The standard error is shown below, and they say it's symptomatic of the client-side firewall not allowing PPTP traffic:
"A connection between the VPN server and the VPN client XXX.XXX.XXX.XXX has been established, but the VPN connection cannot be completed. The most common cause for this is that a firewall or router between the VPN server and the VPN client is not configured to allow Generic Routing Encapsulation (GRE) packets (protocol 47). Verify that the firewalls and routers between your VPN server and the Internet allow GRE packets. Make sure the firewalls and routers on the user's network are also configured to allow GRE packets. If the problem persists, have the user contact the Internet service provider (ISP) to determine whether the ISP might be blocking GRE packets."
I have very little firewall experience and absolutely no Cisco experience I'm afraid. From looking at the PIX config I can see the following line:fixup protocol pptp 1723.Does this mean that the PPTP protcol is enabled on our firewall? Is this for both incoming and outgoing traffic?
I can see no reference to GRE 47 in the PIX config. What I should look for to see if this has been enabled or not?