In the Internet Setup area (WAN) when I change to Static IP I can't change the Subnet Mask from 255.255.255.0 to 255.255.255.240 which is the information currently in my D-Link router. When I try to save the changes I get the error "The IP address is not in the right subnet". I find it hard to believe that a lowly D-Link $35 router has nore capability then a Ciso Small Business Router.
View 1 RepliesI recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.
View 3 Replies View RelatedI just got a WRV 210 wireless router (three of them actually, planning to set up a VPN). But I can't set the admin password. I've tried 4 times, and every time, i've got to hold the reset button to reset to factory settings in order to access the management pages! I enter the new password in both fields, and then click to save the settings. It restarts. Then i try to log in - and it doesn't accept the new password. It doesn't accept the default password. I've tried with admin/(new password) and (new password)/(new password), and admin/admin. None of them work, forcing me to reset router to factory settings. I've tried a password composed of 6 letters followed by a . Thinking that maybe the . was throwing it off, I tried 6 letters followed by 3 numbers. That doesn't work either. I've updated to firmware version 2.0.1.5. No luck.
View 1 Replies View RelatedI've been playing around with the Cisco RV180s for a while now and have come across a problem with the subnet calculation in the static routes and routing table. Essentially, if I configure up a static route for a /16 it's entered in the routing table as a /13. If I add a /24 it's entered in the routing table as a /16. I haven't tested every subnet size and combinations but this looks like a fairly fundamental maths bug.
As a side note, I notice that the 1.0.1.9 release notes state the removal of SSH Server, however, I can not find any reference to it's existance prior to 1.0.1.9, did/does it exist in 1.0.0.30 and if so where? .
Screenshots are below and an extract from the configuration file for reference.
From the config file:
route = {}
route[1] = {}
route[1]["active"] = "1"
route[1]["dstIpAddr"] = "8.8.0.0"
route[1]["gwIpAddr"] = "192.168.1.250(code)
I have a WRV210 Router which I am trying to use VPN remotely to work on my home files while away. I have been able to connect to the router but cannot see any lan network. I have three desktop CPU's 1 W7 and two XP pro operating systems. The one DT I tried stopping fire wall - no lan. I set up an exception in the firewall. I have tried to get you the info thru clips and file capture of the status of the router.
View 1 Replies View RelatedI've began having problems with the WRV210 where the router just reboots. Sometimes it may go for an hour or more then it slips into a series of reboots. The up time varies so I see no pattern. Contacted support they thought the device may have been defective so we did a RMA. Well guess what? The replacement arrived on Friday we put it in place and the same thing is happening. We are not using any of the VPN or VL options. Just simple PAT to a few internal machines for RDP access and an internal exchange server. The Qos is all disabled. It has the newest firmware which I have reflashed. I'm at a loss to explain the behavior but it doesn't appear to be isolated to a defective device.
View 13 Replies View RelatedI am attempting to setup a network containing two routers, a primary giving me ADSL internet access (a 3com 3CRWDR101A-75) and a secondary router that has VPN (Cisco WRV210).
The primary router has the following LAN settings: 192.168.0.1 / 255.255.255.0 with DHCP enabled. WRV210 has the following LAN settings: 192.168.1.1 / 255.255.255.0 with DHCP enabled. Cable connection is from LAN port of first router to Internet port on second router. In this way, I'm able to get internet browsing on 2 laptops connected to WRV210 I have also a Panasonic IP PBX connected on the second LAN (the WRV210)
I need to setup the VPN on WRV210 to be able to get SIP calls from outside of the local networks (through internet). As I am a novice in networking, both routers are on DEFAULT setting.
I have learned a lot during the last 7 days to be able to understand the networking concepts but failed to setup the correct configuration.
For example if I change WRV210 from gateway mode to Router mode, I will not able to browse the internet despite the Help file that says "Select the mode in which this Router will function. If this Router is hosting your networks connection to the Internet, select Gateway. If another Router exists on your network, select Router. When Router is chosen, Dynamic Routing will be enabled"
Also i am able to ping the first LAN 192.168.0.x from WRV210 but not on the other side (from primary router to WRV210).
I am confused to use and combine different settings (NAT, Routing, Ports, ...)
I recently purchased a WRV210 router. I'm trying to set it up and right now I have my server acting as my DHCP server. I can not change this. How can I have the WRV210 recoginize this and pick up on this so that computers connected wirelessly to it will receive IP Addresses from my DHCP Server and not from the router? Right now if I turn all DHCP off, I'm unable to connect to the router.
View 3 Replies View RelatedI have a couple of Linksys WRT54GS V7 routers, they work fine, with the exception that when I login to the web interface, I select the drop down box for DHCP to change it to a static IP, the page refreshes, but comes right back to the same screen with DHCP selected again, I can change the time zone with no issues, I entered the Static DNS info. I've tried a couple of different PC's with a couple of different IE versions. I already updated to the newest firmware, firmware is 7.50.8, I've also factory reset it a couple of times, and I've just run into a brick wall. I've setup hundreds of these routers before so it's not like I don't know how.
View 3 Replies View RelatedI have WRV210-E V01 router and there is only 11 (instead of 13) WiFi channels available. Firmware 2.0.1.5. How to get all 13 channels (European ETSI standard)?
View 1 Replies View RelatedI have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.
Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.
I am trying to connect a new Cisco WRV210 Router to the Internet via a D-Link (Yes I Know - you have to work with what you've got) DSL-320B ADSL2+ Ethernet Modem and can't seem to get a connection.
View 5 Replies View RelatedI got a client who's getting a VOIP system installed into their/my network. The VOIP IT guys are demanding a separate static public IP address to be forward/made available to their router. They will put their phones on a different local subnet.
So here's what I've offered them and they refused:
1. separate PPPOE login; that way we share the modem and each router handles their own session (cleanest solution but they don't want to pay extra)
2. plug their router into DMZ of my WRV210 (they said they require publicly routed IP going direct to their device (but in this case they would have to assign my private IP as their WAN IP and all internet traffic would go to them unfiltered))
our subnet mask is 255.255.255.0....can I change it to something else like 255.255.0.0.
View 4 Replies View RelatedI have a WRV210 router that is not allowing me to delete a VPN client that I had perviously set up. When I go to remove this client on the VPNVPN Client ACCESS table the s/w re-directs me to the Status VPN client table. There I cannot flag/check the disconnect box. I have version 2.0.1.5 s/w which is the latest.
View 0 Replies View RelatedI purchased a WRV210. I configure the device, setup all my tunnels, WAN, LAN, Wirelss, Security, etc. and within 48 hours it "automatically" resets itself back to "out of the box" settings. This has happened twice now - once after it ran for about 4 days and the second time after only 5 or so hours of opperation.
Is this a known issue with the device? Is there an update I need to apply? I'd give ya my current FW version but I cannot login as it appears to have rest once again lol - and my tunnels are down so no remote access.
I made a backup of the config after the first unscheduled reset - (.bin file) so I have my settings ready to restore.
I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
I was configuring a new unit straight out of the box to test a configuration for a client. I got most of of the configuration done and was noticing the menus were quirky and so I check to firmware and discovered it was 1.1.16 (* down level).
I finished my setup and rebooted to complete the changes, when I went back to log into the console it would Actively refuses to connect . the first time after powering on it shows the page title as setup before failing
I have tried a hard reset ( 15 Seconds reset) but it does not work . it doesn't even reset the settings. (static IP etc still there)
how can I get it fixed / exchanged under warranty
- Small Home-Office network based on a Cisco WRV210 VPN Router connected to another WRV210 in a remote location.
- The WRV210 provides 2 WAP-protected SSIDs, one for the office network and one for visitors
- Wireless channel is set 5 channels away of the closest networks (using inSSIDer)
- There are about 12 wireless devices, 4 connected to the office network the rest to visitors. Not all devices are connected at the time of failure. All wireless devices use DHCP which is set to last 1 day and provide 100 IPs.
- The wireless devices are 1 desktop, 3 notebooks (all clean), iPads, iTouch and Nook.
- The failure symptom is that almost daily, and most likely around the same time, no wireless device can connect to any of the SSIDs unless the router is power-cycled. During the failures, which we have witnessed first hand, there are no apparent reasons: no new SSIDs, now SSID in close range on the same channels, nothing we can easily observed in the network in terms of connections or unusual activity.
- A weirdo also presented by the WRV210 was that its web pages were shown erratically. That was corrected by downgrading the firmware from the latest to previous version.
We have used a loaner Linksys router WRT54GC with only the visitor Network on it and even though the situation is not as frequent, it has happened already a couple of times.The WRV210 is out of warranty and discontinued, so we get no support from Cisco that is worth paying for.
How do I change the subnet of a PPTP VPN network on an RV220w?
View 1 Replies View RelatedI have a VPN working between two locations using WRV210s at each end. Now I'm looking to replace one 210 with a new RV110W. Can I get the two to work together? The config is quite different.
View 4 Replies View RelatedI have a DLink wireless bridge connected to the wireless WRV210 router. All devices connected to DLink can access internet/email fine and can ping the WRV210, however, they can not ping any device connected to the WRV210 router, nor can any device on the WRV210 ping devices on the DLink writeless bridge. All devices are on the same subnet, 192,168.100.X with mask 255.255.255.0. All devices get their address from the WRV210.
View 7 Replies View RelatedI'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
I have configured a router WRV210 and I left it enabled in order to access it remotely, but I can not connect to it. I have checked the settings and everything is fine, but if I try to access it from anywhere in the website does not load, either IE or Firefox or Chrome.
View 7 Replies View RelatedI recently updated my firmware in my WRV210 router to Version 2.0.1.5 which is the most recent on Cisco's download page. After upgrading the firmware, I found that some of the administration pages do not appear to load correctly in internet explorer version 9.0.5. For example, the ADMINISTRATION -> MANAGEMENT page has data but to see the data, I have to scroll down about 3 pages. All five entries under STATUS do not have any data visible at all which is typical for most of the other administration pages. An image of the Status Router page is inserted below. I have logged in to the administration pages with an old version of Firefox 3.0.14 and the pages are visible. The operating system that I am running is Windows 7 64bit.
I haven't run across any other entries like on this or other sites.
We have 2 remote locations that are connecting to a server at our home location. Each remote computer uses quickvpn utility to establish a vpn with the home location. Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008. Luckily our sessions in remote desktop stay put but we lose the vpn connection. Most of the time we get a message that the remote gateway is not responding. Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location. We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect.
View 3 Replies View RelatedI am having touble with a NAT concept. What I have is a 3rd party software VPN product that basically tunnels encapsulated traffic to/from a server sitting inside the network. Right now this traffic utiluizes a physical interface on the ASA5510, but I need the interface for another project.
What I have is this:
Internet<----->ASA<-->router<-->4507(layer3)
| |
| |-Vlan1
[Code]......
In Cisco RV110W I configured 2 VLANs, one 192.168.1.xxx(Green Net) and the second 192.168.2.xxx with only one fixed address 192.168.2.100(Server), which is configured in the DMZ Zone. I enabled in Cisco "inter-VLAN-Routing", that is described "routing between the seperate VLANs on the Cisco RV110W" I can Ping the server in one direktion, in the other I got an error. That is all expected and ok! All other expected abilities work well !Now I want to see the server from green net . (firewall in the server is off)I configured Networking/Router with exact the Hint values and got an error : "destination LAN IP cannot be the same as the router IP subnet"
View 5 Replies View RelatedToday I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
How can I edit a static interface IP address? I don't seem to be able to edit the static IP address for my switch. How do I go about changing it? As you can see the IP Address field is not editable.
I have also upgrade to the latest firmware and I cannot figure out how to edit it via that as well.
I have 2 computer connected and both have dynamic IPIf I change one of my computer's IP from dynamic to static Will it be okay to another comp ? ( Can it still connected to Internet / LAN )
View 1 Replies View Relatedi need to change from dynamic IP to Static for work, Iv rang my provider talk talk and the only way i can do this is go to a buisness line and pay more a month is there anyway i can log into my router and change from dynamic to static myself? im not on about the IP thats starts 192.blah blah blah its the one where u go somewhere like whatsmyip.com mine is dynamic as it changes if router is reset, there is hiccup in internet or computer is off for the night etc...
View 2 Replies View RelatedI need assistance regarding changing of DYNAMIC WAN IP to desired WAN IP to connect my e-mail server of my office, Problem is :i have a dynamic WAN IP at my home internet router , and my e-mail server at office only allows assigned WAN ips to connect , I want to connect from my home, i know the WAN ips which are allowed to connect my e-mail server and i want to change my dynamic wan ip virutally to desired WAN ip for incoming and outgoing traffic from my wireless router, What I need to do :I need to change my dynamic WAN IP to an static desired ip at my wireless router?
View 4 Replies View Related