Cisco Routers :: WRV210 Freezes / Hanging / Lock / VPN Don't Reconnect

Dec 21, 2010

I'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
 
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
 
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
 
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.

View 19 Replies


ADVERTISEMENT

Cisco Routers :: RVS4000 - Connection To Netflix Dropping / Firewall Hanging

Feb 22, 2012

The firewall on my RVS4000 appears to hang when ever I use Netflix. If I disable the firewall and re-enable it it works for a while and then stops again. My IP address is in the Approved Client IP Addresses so it is excluded from the URL filtering and Web reputation rules.

View 5 Replies View Related

Cisco Routers :: WRV210 - Only 11 Wi-Fi Channels Available

Nov 28, 2011

I have WRV210-E V01 router and there is only 11 (instead of 13) WiFi channels available. Firmware 2.0.1.5. How to get all 13 channels (European ETSI standard)?

View 1 Replies View Related

Cisco Routers :: Lock LAN IP To One WAN Port On RV042?

Jun 24, 2012

I'd like to use load balancing with the RV042, but I have some devices that don't react well to not always using the same outgoing port (like a credit card machine, for instance). Is it possible for me to create some "rule" with the RV042 that an internal IP address will use a certain WAN port? And if so, when that WAN port goes down will the RV042 fail-over to the other active WAN port? I was able to do this with a Xincom XC-OPG502 (which is being replaced with the RV042).

View 1 Replies View Related

Cisco Routers :: WRVS4400N Lock Up / Freeze?

May 3, 2013

In the last couple weeks my router has begun to lock up / freeze.  Not sure the appropriate terminology to use for this.  The end result is wireless and wired connections stop functioning.  I can't connect to the routers web interface via wired.  I can't connect to any of the wireless SIDs.  The router just doesn't respond.  When I look at the router the lights are still blinking, but nobody seems to be home.  I have to unplug the router and do a 30 count and plug it back in to get it to return to working order.At the time that this first occurred I mad not made any changes to the device in months, if not longer.  Was running great.  Not sure what happened.

View 7 Replies View Related

Cisco Routers :: WRV210 - Url Filtering Won't Work

Feb 21, 2011

I have a big problem with my cisco wrv210. I want to use URL Filtering to block facebook.

Enable
ip range : 192.168.2.5-192.168.2.254
url string : Facebook, www.facebook.com , facebook.com notting work.

View 1 Replies View Related

Cisco Routers :: Connect WRV210 To Internet?

Aug 24, 2011

I am trying to connect a new Cisco WRV210 Router to the Internet via a D-Link (Yes I Know - you have to work with what you've got) DSL-320B ADSL2+ Ethernet Modem and can't seem to get a connection.

View 5 Replies View Related

Cisco Routers :: WRV210 - Cannot See LAN After Connecting VPN To Router

Aug 14, 2011

I have a WRV210 Router which I am trying to use VPN remotely to work on my home files while away. I have been able to connect to the router but cannot see any lan network. I have three desktop CPU's 1 W7 and two XP pro operating systems. The one DT I tried stopping fire wall - no lan. I set up an exception in the firewall.  I have tried to get you the info thru clips and file capture of the status of the router.

View 1 Replies View Related

Cisco Routers :: WRV210 Router Just Reboots

Jun 13, 2011

I've began having problems with the WRV210 where the router just reboots.  Sometimes it may go for an hour or more then it slips into a series of reboots.  The up time varies so I see no pattern.  Contacted support they thought the device may have been defective so we did a RMA.  Well guess what?  The replacement arrived on Friday we put it in place and the same thing is happening.  We are not using any of the VPN or VL options.  Just simple PAT to a few internal machines for RDP access and an internal exchange server.  The Qos is all disabled.  It has the newest firmware which I have reflashed.  I'm at a loss to explain the behavior but it doesn't appear to be isolated to a defective device. 

View 13 Replies View Related

Cisco Routers :: Setup VPN On WRV210 As Second Router

Dec 12, 2012

I am attempting to setup a network containing two routers, a primary giving me ADSL internet access (a 3com 3CRWDR101A-75) and a secondary router that has VPN (Cisco WRV210).
 
The primary router has the following LAN settings: 192.168.0.1 / 255.255.255.0 with DHCP enabled. WRV210 has the following LAN settings: 192.168.1.1 / 255.255.255.0 with DHCP enabled. Cable connection is from LAN port of first router to Internet port on second router. In this way, I'm able to get internet browsing on 2 laptops connected to WRV210 I have also a Panasonic IP PBX connected on the second LAN (the WRV210)
 
I need to setup the VPN on WRV210 to be able to get SIP calls from outside of the local networks (through internet). As I am a novice in networking, both routers are on DEFAULT setting.
 
I have learned a lot during the last 7 days to be able to understand the networking concepts but failed to setup the correct configuration.
 
For example if I change WRV210 from gateway mode to Router mode, I will not able to browse the internet despite the Help file that says "Select the mode in which this Router will function. If this Router is hosting your networks connection to the Internet, select Gateway. If another Router exists on your network, select Router. When Router is chosen, Dynamic Routing will be enabled"
 
Also i am able to ping the first LAN 192.168.0.x from WRV210 but not on the other side (from primary router to WRV210).
 
I am confused to use and combine different settings (NAT, Routing, Ports, ...)

View 6 Replies View Related

Networking :: 1 DSL Modem With 2 Routers WRV210

Sep 12, 2011

I got a client who's getting a VOIP system installed into their/my network. The VOIP IT guys are demanding a separate static public IP address to be forward/made available to their router. They will put their phones on a different local subnet.

So here's what I've offered them and they refused:

1. separate PPPOE login; that way we share the modem and each router handles their own session (cleanest solution but they don't want to pay extra)
2. plug their router into DMZ of my WRV210 (they said they require publicly routed IP going direct to their device (but in this case they would have to assign my private IP as their WAN IP and all internet traffic would go to them unfiltered))

View 9 Replies View Related

Cisco Routers :: WRV210 Not Allowing To Delete VPN Client

Sep 27, 2011

I have a WRV210 router that is not allowing me to delete a VPN client that I had perviously set up. When I go to remove this client on the VPNVPN Client ACCESS table the s/w re-directs me to the Status VPN client table. There I cannot flag/check the disconnect box. I have version 2.0.1.5 s/w which is the latest.

View 0 Replies View Related

Cisco Routers :: WRV210 Resets To Factory Defaults?

Sep 23, 2010

I purchased a WRV210. I configure the device, setup all my tunnels, WAN, LAN, Wirelss, Security, etc. and within 48 hours it "automatically" resets itself back to "out of the box" settings. This has happened twice now - once after it ran for about 4 days and the second time after only 5 or so hours of opperation.
 
Is this a known issue with the device? Is there an update I need to apply? I'd give ya my current FW version but I cannot login as it appears to have rest once again lol - and my tunnels are down so no remote access.
 
I made a backup of the config after the first unscheduled reset - (.bin file) so I have my settings ready to restore.

View 6 Replies View Related

Cisco Routers :: WRV210-A V01 Reset To Factory Default?

Oct 30, 2011

I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
 
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
 
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
 
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.

View 1 Replies View Related

Cisco Routers :: WRV210 - No Access To Configuration Menu

Aug 10, 2011

I was configuring a new unit straight out of the box to test a configuration for a client.  I got most of of the configuration done and was noticing the menus were quirky and so I check to firmware and discovered  it was 1.1.16 (* down level).
 
I finished my setup and rebooted to complete the changes, when I went back to log into the console it would Actively refuses to connect . the first time after powering on it shows  the page title as setup before failing 
 
I have tried a hard reset ( 15 Seconds reset) but it does not work . it doesn't even reset the settings.    (static IP  etc still there)
 
how can I get it fixed  / exchanged under warranty

View 1 Replies View Related

Cisco Routers :: Static IP Address For WRV210 Wireless

Nov 6, 2011

I recently switched operating systems from XP to Windows 7. Since that time whenever I need to reboot the router, it does not recognize my printer. How do I set the router to a static ip address and will that affect its recognition of my computer? I have had no problems with computer recognition, only printer.

View 3 Replies View Related

Cisco Routers :: WRV210 Wireless Frequent Disconnections

Feb 18, 2013

- Small Home-Office network based on a Cisco WRV210 VPN Router connected to another WRV210 in a remote location.
- The WRV210 provides 2 WAP-protected SSIDs, one for the office network and one for visitors
- Wireless channel is set 5 channels away of the closest networks (using inSSIDer)
- There are about 12 wireless devices, 4 connected to the office network the rest to visitors. Not all devices are connected at the time of failure. All wireless devices use DHCP which is set to last 1 day and provide 100 IPs.
- The wireless devices are 1 desktop, 3 notebooks (all clean), iPads, iTouch and Nook.
- The failure symptom is that almost daily, and most likely around the same time, no wireless device can connect to any of the SSIDs unless the router is power-cycled. During the failures, which we have witnessed first hand, there are no apparent reasons: no new SSIDs, now SSID in close range on the same channels, nothing we can easily observed in the network in terms of connections or unusual activity.
- A weirdo also presented by the WRV210 was that its web pages were shown erratically. That was corrected by downgrading the firmware from the latest to previous version.
 
We have used a loaner Linksys router WRT54GC with only the visitor Network on it and even though the situation is not as frequent, it has happened already a couple of times.The WRV210 is out of warranty and discontinued, so we get no support from Cisco that is worth paying for.

View 1 Replies View Related

Cisco Routers :: WRV210 Unable To Connect To Router

Sep 26, 2011

I recently purchased a WRV210 router.  I'm trying to set it up and right now I have my server acting as my DHCP server.  I can not change this.  How can I have the WRV210 recoginize this and pick up on this so that computers connected wirelessly to it will receive IP Addresses from my DHCP Server and not from the router?  Right now if I turn all DHCP off, I'm unable to connect to the router. 

View 3 Replies View Related

Cisco Routers :: RV110W Replacement For WRV210 IPsec VPN Tunnel Between Them

Aug 26, 2012

I have a VPN working between two locations using WRV210s at each end. Now I'm looking to replace one 210 with a new RV110W. Can I get the two to work together? The config is quite different.

View 4 Replies View Related

Cisco Routers :: WRV210 - Can't Ping Other Devices On DLink Bridge

Sep 4, 2011

I have a DLink wireless bridge connected to the wireless WRV210 router.   All devices connected to DLink can access internet/email fine and can ping the WRV210, however, they can not ping any device connected to the WRV210 router, nor can any device on the WRV210 ping devices on the DLink writeless bridge.  All devices are on the same subnet, 192,168.100.X  with mask 255.255.255.0.  All devices get their address from the WRV210.

View 7 Replies View Related

Cisco Routers :: WRV210 Router - Can't Change Static WAN Subnet To 240

Sep 20, 2011

In the Internet Setup area (WAN) when I change to Static IP I can't change the Subnet Mask from 255.255.255.0 to 255.255.255.240 which is the information currently in my D-Link router.  When I try to save the changes I get the error "The IP address is not in the right subnet".  I find it hard to believe that a lowly D-Link $35 router has nore capability then a Ciso Small Business Router. 

View 1 Replies View Related

Cisco Routers :: Can't Access Remotely WRV210 - Website Does Not Load?

Nov 22, 2011

I have configured a router WRV210 and I left it enabled in order to access it remotely, but I can not connect to it. I have checked the settings and everything is fine, but if I try to access it from anywhere in the website does not load, either IE or Firefox or Chrome.

View 7 Replies View Related

Cisco Routers :: WRV210 Administration Pages Not Visible In Internet Explorer

Feb 17, 2012

I recently updated my firmware in my WRV210 router to Version 2.0.1.5 which is the most recent on Cisco's download page. After upgrading the firmware, I found that some of the administration pages do not appear to load correctly in internet explorer version 9.0.5. For example, the ADMINISTRATION -> MANAGEMENT page has data but to see the data, I have to scroll down about 3 pages. All five entries under STATUS do not have any data visible at all which is typical for most of the other administration pages.  An image of the Status Router page is inserted below.   I have logged in to the administration pages with an old version of Firefox 3.0.14 and the pages are visible. The operating system that I am running is Windows 7 64bit.
 
I haven't run across any other entries like on this or other sites. 

View 1 Replies View Related

Cisco Routers :: WRV210 - Quickvpn Disconnects - Remote Gateway Not Responding

Oct 2, 2012

We have 2 remote locations that are connecting to a server at our home location.  Each remote computer uses quickvpn utility to establish a vpn with the home location.  Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008.  Luckily our sessions in remote desktop stay put but we lose the vpn connection.  Most of the time we get a message that the remote gateway is not responding.  Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location.  We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect. 

View 3 Replies View Related

Cisco Routers :: RV220W Disconnect / Reconnect WAN

Oct 10, 2011

I have and D-Link modem which is bridged and a PPPoAPPPoE profile set up on the RV220W for my ADSL2+ connection.I cannot for the life of me find anywhere in the routers config web pages to tell the modem to disconnect or reconnect the connetion to the ISP.The reason I want this is because I need to make sure the correct signaling is sent before the connection is stopped so that the exchange doesnt see this as a drop out and reduce our line speed to compensate.

View 1 Replies View Related

Cisco Routers :: WAG160Nv2 Wireless Router Freezes?

Aug 7, 2012

We have had a Cisco WAG160Nv2 wireless router here for home use, brand new for perhaps just 2 months. And we have been mostly happy, except that it sometimes freezes up for no apparent reason.
 
When I say "freeze up", I mean that all the connected PCs - ethernet or wireless - have no internet. And that indeed, there is no wireless signal at all. But yet it actually looks as if it is still working. All the lights on the front panel that should be green are still green. But yet, when I attempt to access the router's setup through the browser as normal, that isn't available either. So I can't even access the router's setup, to check for errors in the log.But yet it isn't an ISP problem either. Because every time this happens, the solution is to turn the router off and then back on. And that works every time. So it seems to be a router problem, not an ISP problem.

View 1 Replies View Related

Cisco Routers :: RV082 To ASA 5510 Tunnel Freezes After 8 Hours?

Apr 18, 2012

I have a RV082 that has an issue keeping an IPSEC Gateway to Gateway VPN running from itself to our ASA 5510. At 8 hours of connectivity (I can almost set a clock to it) the Tunnel will say it is connected on the RV082 but on the ASA 5510 the tunnel is not up.
 
If I click on disconnect on the RV082 under the VPN Summary page things will come back up. from the ASA 5510 side there is nothing I can do to get things back (ping inside "vpn network" or even trying to make a connection to a networked VPN machine).
 
To make things more complicated I have another VPN on the RV082 to a PIX 506e that works with no issues. I also have another RV082 at another location with the same settings that keeps its tunnel with the ASA 5510 with out any issue. Some things I have tried to try and fix the issue are:
 
I upgrade the firmware on the Rv082 V3 from 4.0.0.7-tm (what it was shipped with) to 4.1.1.01-sp) - This seemed to have no effect.
 
on the RV082 I have changed the MTU from automatic to 1428 and 1452 - all this does is make the connection to the PIX 506e unstable like it is for the ASA 5510 I have changed this back to automatic.
 
since the time of stability seems to be 8 hours I have changed the "Phase 1 SA life time" and "Phase 2 SA life time" to 28800 both at the same time and individually - This seemed to have no effect.
 
The current configuration on the RV082 are:
Local security gateway type: IP Only
IP address: (local ISP provided static IP address)

[Code]......

View 19 Replies View Related

Cisco Routers :: RVS4000 Freezes When Pushing Data Through VPN Tunnel

Jul 26, 2011

My RVS4000 router freezes up when a lot of data is being pushed through the Ipsec tunnel. Let me explain in detail.
 
On physical location A, I have an RVS4000 router (with IP 192.168.3.1) which is permanently connected with a WRVS4400 router (with IP 192.168.1.1) on physical location B. The Ipsec tunnel has been configured using the Easy Setup Wizard of Cisco and has been working fine and stable for months. Both routers have another Ipsec tunnel with another WRVS4400 router (with IP 192.168.2.1) on physical location C, but this router does not play a role in the problem below.Recently, I’m trying to set up a remote backup service between physical location A and B using “rsync”, which uses port 873. Due to the Ipsec/VPN tunnel, I could configure rsync to move the backup files from our NAS on location A (NAS has IP 192.168.1.2) directly to location B (NAS has IP 192.168.3.2). Both NAS-devices are of the brand Synology (DS211J). The Ipsec tunnel guarantees that the data is coded and thus secure.
 
However, when pushing the first batch of data, I noticed that the router on the receiving end (RVS4000) freezes up after approx. 1,5h after the batch has started, which is after approx. 1 gigabyte of data has been transmitted. The connection with the WAN is lost, also the VPN-tunnel is not working, I cannot ping the device or reach its configuration pages (on 192.168.3.1), the only option is unplugging it and letting it reboot. I’m thinking the router cannot deal with the huge amount of data that needs to be decoded. I tried 5/6 times, with always the same result (timing / amount of data pushed through before router freezes varies slightly).

View 11 Replies View Related

Cisco Routers :: RV082 Freezes Every 2 Hours When Using Ipsec Tunnel

Jul 5, 2011

i have an ipsec tunnel between two rv082 routers. (1 v3 Hardware and the other with v2). On both devices are the latest firmware installed.
 
Everything working fine, the routers establish an ipsec connection but after about two hours, the router with hw version 3 freezes.... nor the wan neither der lan interface is pingable. I can only pull out the power cord. Below attached are the ipsec settings. It´s a Gateway to Gateway connection

View 7 Replies View Related

Cisco Routers :: QuickVPN V1.4.2.1 (RV082) Uninstall Freezes In Windows 7

May 29, 2013

I installed QuickVPN v1.4.2.1 as it was in the download section on Linksys: [URL]

for the RV082 router we have. It connected but the program seemed buggy as there seemed to be no way to close the program after I used it so I wanted to uninstall it and install a more recent version of QuickVPN (side question: is it possible to VPN connect to my RV082 router with a different version of QuickVPN?).
 
I have Windows 7 Professional 64bit SP1 with all the latest updates. When I try to uninstall the program, at about the 25% mark of the window for 'QuickVPN Client Setup is preparing the InstallShield Wizard, which will guide you through the rest of the setup process. Please wait.' it seems to stop responding as holding the mouse over that windows just displayes a ring which goes round and round. I regret installing this buggy software on my PC.

View 3 Replies View Related

Belkin Routers :: 690 / F9K1002V4 - Wireless Router Won't Reconnect

Apr 18, 2013

I have a Belkin 690, model# F9K1002V4 that's been working great until I had to turn off and disconnect some things in order to replace my old tv stand. After I straightened out the mess of wires from everything and made sure all the connections were good all the other components including my satellite modem were working fine, but the wireless router won't reconnect. It's working fine with a cable but won't work wireless even though the blue indicator shows the actual router to be working okay. I've repeatedly reset/re-powered the router to no avail. Firmware is up to date.

View 1 Replies View Related

Cisco Routers :: Rv120w Freezes When User Prints A Large Document

Jun 4, 2012

I have a customer with the following topology:
 
Dallas: Netopia R910 router Windows 2003 Server
 
San Antonio: Cisco RV120W Router Thin client devices connecting to Windows 2003 Server Okidata 3410 Dot Matrix printer with Dlink DP301P+ Print Server attached to Parallel Port
 
If a user sends a picking ticket larger than 6 or 7 pages (not really that much data) to the Okidata printer with the attached print server, the RV120W router will completely lock up.  The connection between the two routers is lost, and the router must be physically rebooted.  This behaviour is fairly consistent on the larger documents described.  Pick tickets of less than 6 pages print without any issues.  I've examined the data stream and see nothing of consequence in the larger documents.  There is no effect on the Dallas router.
 
An IPSEC tunnel exists between the two routers. what could be causing the router to freeze?

View 5 Replies View Related

Cisco :: Prime LMS 4.2 Browser Hanging

Sep 14, 2012

We have Cisco Prime 4.2 installed Windows 2008 R2 server, I am facing problem when I am going under Report>Fault & events or any other section, the browser gets stuck in loading page and become unresponsive. If I restrart the Daemon manager service it works fine for some time and again start giving problem in two or three hours time interval.I also face the same problem when I go to Admin > Job browser window.Does any one face the same problem,I have changed the host name of thserver using script and also generated new SSL certificate and I tried with diffrent browsers but problem is still persisting.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved