Cisco Routers :: Rv120w Freezes When User Prints A Large Document
Jun 4, 2012
I have a customer with the following topology:
Dallas: Netopia R910 router Windows 2003 Server
San Antonio: Cisco RV120W Router Thin client devices connecting to Windows 2003 Server Okidata 3410 Dot Matrix printer with Dlink DP301P+ Print Server attached to Parallel Port
If a user sends a picking ticket larger than 6 or 7 pages (not really that much data) to the Okidata printer with the attached print server, the RV120W router will completely lock up. The connection between the two routers is lost, and the router must be physically rebooted. This behaviour is fairly consistent on the larger documents described. Pick tickets of less than 6 pages print without any issues. I've examined the data stream and see nothing of consequence in the larger documents. There is no effect on the Dallas router.
An IPSEC tunnel exists between the two routers. what could be causing the router to freeze?
View 5 Replies
ADVERTISEMENT
Jan 15, 2013
have a Cisco RV120W and I need setup a Quick VPN user, however i can't enable this user.I have Remote Management enable, access type All Ip Address and port number 443.
View 3 Replies
View Related
Jan 13, 2009
I have a N600dp. My printer, Brother MFC-J410W, is plugged into the router USB port. The printer function works but the scanner function doesn't. I keep getting an error message that the printer is not connected.
View 5 Replies
View Related
Aug 7, 2012
We have had a Cisco WAG160Nv2 wireless router here for home use, brand new for perhaps just 2 months. And we have been mostly happy, except that it sometimes freezes up for no apparent reason.
When I say "freeze up", I mean that all the connected PCs - ethernet or wireless - have no internet. And that indeed, there is no wireless signal at all. But yet it actually looks as if it is still working. All the lights on the front panel that should be green are still green. But yet, when I attempt to access the router's setup through the browser as normal, that isn't available either. So I can't even access the router's setup, to check for errors in the log.But yet it isn't an ISP problem either. Because every time this happens, the solution is to turn the router off and then back on. And that works every time. So it seems to be a router problem, not an ISP problem.
View 1 Replies
View Related
Feb 7, 2012
I would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
View 1 Replies
View Related
Apr 18, 2012
I have a RV082 that has an issue keeping an IPSEC Gateway to Gateway VPN running from itself to our ASA 5510. At 8 hours of connectivity (I can almost set a clock to it) the Tunnel will say it is connected on the RV082 but on the ASA 5510 the tunnel is not up.
If I click on disconnect on the RV082 under the VPN Summary page things will come back up. from the ASA 5510 side there is nothing I can do to get things back (ping inside "vpn network" or even trying to make a connection to a networked VPN machine).
To make things more complicated I have another VPN on the RV082 to a PIX 506e that works with no issues. I also have another RV082 at another location with the same settings that keeps its tunnel with the ASA 5510 with out any issue. Some things I have tried to try and fix the issue are:
I upgrade the firmware on the Rv082 V3 from 4.0.0.7-tm (what it was shipped with) to 4.1.1.01-sp) - This seemed to have no effect.
on the RV082 I have changed the MTU from automatic to 1428 and 1452 - all this does is make the connection to the PIX 506e unstable like it is for the ASA 5510 I have changed this back to automatic.
since the time of stability seems to be 8 hours I have changed the "Phase 1 SA life time" and "Phase 2 SA life time" to 28800 both at the same time and individually - This seemed to have no effect.
The current configuration on the RV082 are:
Local security gateway type: IP Only
IP address: (local ISP provided static IP address)
[Code]......
View 19 Replies
View Related
Jul 26, 2011
My RVS4000 router freezes up when a lot of data is being pushed through the Ipsec tunnel. Let me explain in detail.
On physical location A, I have an RVS4000 router (with IP 192.168.3.1) which is permanently connected with a WRVS4400 router (with IP 192.168.1.1) on physical location B. The Ipsec tunnel has been configured using the Easy Setup Wizard of Cisco and has been working fine and stable for months. Both routers have another Ipsec tunnel with another WRVS4400 router (with IP 192.168.2.1) on physical location C, but this router does not play a role in the problem below.Recently, I’m trying to set up a remote backup service between physical location A and B using “rsync”, which uses port 873. Due to the Ipsec/VPN tunnel, I could configure rsync to move the backup files from our NAS on location A (NAS has IP 192.168.1.2) directly to location B (NAS has IP 192.168.3.2). Both NAS-devices are of the brand Synology (DS211J). The Ipsec tunnel guarantees that the data is coded and thus secure.
However, when pushing the first batch of data, I noticed that the router on the receiving end (RVS4000) freezes up after approx. 1,5h after the batch has started, which is after approx. 1 gigabyte of data has been transmitted. The connection with the WAN is lost, also the VPN-tunnel is not working, I cannot ping the device or reach its configuration pages (on 192.168.3.1), the only option is unplugging it and letting it reboot. I’m thinking the router cannot deal with the huge amount of data that needs to be decoded. I tried 5/6 times, with always the same result (timing / amount of data pushed through before router freezes varies slightly).
View 11 Replies
View Related
Jul 5, 2011
i have an ipsec tunnel between two rv082 routers. (1 v3 Hardware and the other with v2). On both devices are the latest firmware installed.
Everything working fine, the routers establish an ipsec connection but after about two hours, the router with hw version 3 freezes.... nor the wan neither der lan interface is pingable. I can only pull out the power cord. Below attached are the ipsec settings. It´s a Gateway to Gateway connection
View 7 Replies
View Related
Dec 21, 2010
I'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
View 19 Replies
View Related
May 29, 2013
I installed QuickVPN v1.4.2.1 as it was in the download section on Linksys: [URL]
for the RV082 router we have. It connected but the program seemed buggy as there seemed to be no way to close the program after I used it so I wanted to uninstall it and install a more recent version of QuickVPN (side question: is it possible to VPN connect to my RV082 router with a different version of QuickVPN?).
I have Windows 7 Professional 64bit SP1 with all the latest updates. When I try to uninstall the program, at about the 25% mark of the window for 'QuickVPN Client Setup is preparing the InstallShield Wizard, which will guide you through the rest of the setup process. Please wait.' it seems to stop responding as holding the mouse over that windows just displayes a ring which goes round and round. I regret installing this buggy software on my PC.
View 3 Replies
View Related
Jan 12, 2012
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
View 2 Replies
View Related
Feb 8, 2012
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies
View Related
Sep 24, 2011
Upgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
View 2 Replies
View Related
Mar 31, 2012
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
View 3 Replies
View Related
Sep 12, 2011
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
View 2 Replies
View Related
Aug 6, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....
View 1 Replies
View Related
Nov 21, 2012
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
[Code]....
Now, I need to be able to reach the server (192.168.1.100) from a PC on LAN #2 with IP 192.168.2.50. So, I've created au static route on Office Router #2 (192.168.2.1) because of course it doesn't know how to reach private subnet 192.168.1.x. My static route looks like this :
192.168.1.0 / 24 (Destination network) --- 192.168.2.254 (Gateway)
...but it doesn't work, no ping. When I do a tracert to server IP (192.168.1.100) from PC on LAN #2 (192.168.2.50), the result is :
1st jump ---> 192.168.2.1
2nd jump --> 192.168.2.254
...and it doesn't go further.
View 3 Replies
View Related
Dec 21, 2011
I configured my RV120W (Firmware:1.0.2.6) to count the traffic on my network. I set the monthly limit to 99999 and did not change anything else.So after a few hours, the traffic counter shows 2048 MB for outgoing traffic. This is impossible, because the DSL-connection is too limited in upload to cause this huge outgoing traffic in 6-8 hours. When I reset the counter at night, the next morning the device shows 2048MB again (even if there was no traffic at all, just some clients syncing time with NTP). I did already reset the device to factory defaults and reconfigured everything from scratch.
View 0 Replies
View Related
Jul 5, 2012
I have a problem with firewall rules. If I set some rules for open communication and some for closed, so I cannot reorder from the end to begin.
Last rules are at the end of all. So I can only reorder in one pages.(I have about 33 rules = 3 pages of rules)
View 4 Replies
View Related
Oct 24, 2011
I was wondering if I could setup my router CIsco RV120W to be able to connect to a VPN serice for my internet connection. Looking to give my small home netwok more sercurity. Is it possible with the Cisco firmware to be able to setup a connection to VPN serice. Do I have the compabilites with this router?
View 1 Replies
View Related
Aug 22, 2011
The PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies
View Related
Apr 26, 2012
I need to configure a rv120w in order to make it work at the same time for data and digital tv. The fact is that the set top box for the idtv needs an IP address that will be delivered directly from the ISP. So I need to setup one LAN port that will be bridged to the WLAN connection (the stb will be connected to that lan port), and another port that will be connected to the LAN swicth so that the rest of the network has internet access. I can't see anywhere a way to create such a bridge. Quite disappointing as it's possible to do so on open source platforms such as openWRT..
View 3 Replies
View Related
Oct 30, 2011
When I try to export an SSL Certificate for a Client I get a htps . CSR file instead of the .PEM file. So, I can't update the client computer with the correct certificate.
Firmware: 1.0.2.6
View 3 Replies
View Related
Mar 25, 2012
I have just received an RV120W. Default setup (out of box), but when I http://192.168.1.1 and login, the next page comes up as : Internet Explorer cannot display the webpage ? Internet Explorer is version 9.
I have allowed both http and https at 192.168.1.1 in Internet Explorer security settings/Trusted Sites ?
Is there a console connection to this box ?
View 3 Replies
View Related
Oct 16, 2012
Is it possible to have 2 IP addresses on wan and setup specific routing rules for each IP ? Or do I need to use another router for that and if which one ?
View 4 Replies
View Related
Apr 29, 2012
Where can I download the new firmware 1.0.3.10 for RV120W?
[URL]
View 25 Replies
View Related
Oct 29, 2011
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
View 11 Replies
View Related
Nov 6, 2012
I gave setup a vpn gateway between two cisco RV120W. The connection is established.
Active IPsec Security Association Table: Policy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA Established Poll Interval: (Seconds)
The problem is that there is no trafic. Even ping te remote internal nework is not working. For testing i have disabeld at both sites te firewall and have configured both with an access rule any to any.
View 1 Replies
View Related
Mar 6, 2012
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies
View Related
Jun 2, 2013
Trying to setup Three networks all with different IP ranges.I assume I can create a new VLAN and associate that VLAN with one of the four available ports.
Port 1 can have 192.168.1.1 - 254, Port 2 can have 192.168.2.1 - 254 and Port 3 can have 10.0.1.1 - 254.
But the Admin guide I just downloaded is NOT for 10.0.4.10. It shows Networking > LAN > VLAN Configuration.My screens show Networking > LAN > VLAN Membership.
So I am not sure how to make Port 2 associate with VLAN98 ( I created VLAN98 and 99 for the other two networks). There is a membership table that you can Tag or untag for each of the four ports - is that it ?
View 2 Replies
View Related
Aug 27, 2012
I recently purchased a RV120W router and I am having a problem selecting n speed under the wireless settings.
If I select B/G/N-Mixed mode then when I go to save the change I get B/G/N-Mixed B/G/N-Mixed in red letters and it does not save. If I select N only then when I go to save it says in red letters N only N only.
It does not matter if I pick 20 only or 20/40. It does not matter if I enable or disable U-APSD. It does not matter if I use the LSB or USB side.
Firmware Version:1.0.3.10 :When I got the router it had an older firmware if I remember correctly, and it would let me change to n speed.
View 3 Replies
View Related
Oct 12, 2011
Looking for assistance in setting up a VPN Connection on a RV120w.Trying to establish VPN with Android tablets utilizing Anyconnect.I currently utilize IPsec connections into RV120w without issues from desktops/laptops. (I am not real familiar with certificate based connection, and how to export from RV120w and import into Android)
View 2 Replies
View Related
Aug 10, 2011
I have RV 120W Wireless-N VPN Firewall and having issues with connectivity and communication between PCs within the same LAN. I tried the following to check connections:
1. Finding the computers within the workgroup using wondows network or (finding the computer) without avail.
2. Pinging the IP address of the PCs within the LAN. Request Timeout is given.
3. Pinter Network is working fine.
View 6 Replies
View Related
