Cisco Routers :: RV220W Disconnect / Reconnect WAN
Oct 10, 2011
I have and D-Link modem which is bridged and a PPPoAPPPoE profile set up on the RV220W for my ADSL2+ connection.I cannot for the life of me find anywhere in the routers config web pages to tell the modem to disconnect or reconnect the connetion to the ISP.The reason I want this is because I need to make sure the correct signaling is sent before the connection is stopped so that the exchange doesnt see this as a drop out and reduce our line speed to compensate.
View 1 Replies
ADVERTISEMENT
Jan 8, 2011
My Internet will disconnect & then reconnect constantly. I have 2 laptops & they are both on my home network & I have no trouble with the other one so I assume there is nothing wrong with both the Internet service & router. The laptop with the problem is an acer/aspire 5720z. The Wireless Network Adapter is a Atheros AR5007EG. When I go to the Adapter Properties the status reads "The device is working properly". When I go to Control Panel>Network & Sharing Center my Wireless Network Connection Signal Strength reads Excellent. The operating system is Windows Vista Home Premium.
View 5 Replies
View Related
Apr 29, 2012
The wrt400n works fine. Except randomly every day or every other day, laptops cannot connect to the router. Router lights are still on, blinking, etc, no change there. Releasing/renewing IP doesn't work. Turning off wireless radio on laptop and back on doesn't work.Unplugging and replugging in the router DOES work, and laptops can connect to the router again.Router is updated to 1.0.02 firmware, sine I thought that was the problem, but after firmware update, problem is still occurring.Wireless is set to mixed,channel width is auto?
View 14 Replies
View Related
May 15, 2011
When doing anything on my PC, gaming, browsing, whatever, I will have random disconnects for a few seconds and it will reconnect. I don't get the "your network cable has been unplugged" message, it just stops working for a second or two and starts working again. This has been happening for a few months after a fresh install of windows xp and I haven't really tried to fix it.Every other computer in the house is fine except this one, it can't be the modem because a new one was installed a few days ago and its the same problem. The router was reset within the last week as well. I think the problem is with this computer alone but I don't know where to look. The problem didn't happen for a few days after I put a new network card in, but soon after it continued happening. I also have tried a few different CAT5 cables, even the XBOX one but nothing resolved the issue.
View 4 Replies
View Related
Jan 22, 2013
I have a WLC 5508 in my datacenter, and 1142s configured with FlexConnect at a remote site.Two issues:Some APs 'die' from time to time where I cannot ping them anymore and they do not service any clients. I can reset them from the WLC after which they work again. I have some clients in the building (same area) who lose connectivity from time to time and are unable to reconnect to the wireless. I am seeing errors that the gateway cannot be found or there is not a valid IP. restarting the AP closest to the clients fixes the issue. I have replaced the AP and connected to a different port on the switch.
View 6 Replies
View Related
Dec 21, 2010
I'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
View 19 Replies
View Related
Apr 18, 2013
I have a Belkin 690, model# F9K1002V4 that's been working great until I had to turn off and disconnect some things in order to replace my old tv stand. After I straightened out the mess of wires from everything and made sure all the connections were good all the other components including my satellite modem were working fine, but the wireless router won't reconnect. It's working fine with a cable but won't work wireless even though the blue indicator shows the actual router to be working okay. I've repeatedly reset/re-powered the router to no avail. Firmware is up to date.
View 1 Replies
View Related
Mar 3, 2011
we bought a router for our company RV042, so far good
What i did:
1. i created QuickVPN clients, droped in certificate which exported from router
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
The users are connecting sucesefully to router and using resources from server etc...
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
Only sometimes the clients disconnect properly from router, but it is very very rare...
Question1: Where I should look for the problem in router rv042 or client laptops?
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
I have latest quickvpn software and latest router firmware.
View 10 Replies
View Related
Jun 28, 2012
Where is the disconect button on the VPN Status page gone in FW:1.01.26 (003) ? It used to be there as you can see in the below screen shots...
FW: 1.01.19(004)
FW: 1.01.26 (003)
View 6 Replies
View Related
Dec 26, 2012
i need step by step instruction to disconnect and reset my Belkin 450 DB router
View 1 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Jul 3, 2012
Picked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
View 9 Replies
View Related
May 15, 2012
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
View 5 Replies
View Related
Dec 12, 2012
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
View 8 Replies
View Related
Sep 28, 2011
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jun 23, 2012
Having a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies
View Related
Jan 26, 2012
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies
View Related
Nov 20, 2012
Nothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies
View Related
Jan 31, 2013
When someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies
View Related
Sep 26, 2011
Where I can find the MIB files for RV220W router?
View 2 Replies
View Related
Aug 5, 2011
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
View 12 Replies
View Related
Apr 30, 2013
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies
View Related
Jan 8, 2012
I have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously
View 1 Replies
View Related
Jul 18, 2011
I have an Cisco RV220W and I can’t connect to web interface. The router is new, I receive the error in Mozilla: Cannot communicate securely with peer: no common encryption algorithm(s). I used also Internet Explorer, Chrome , I tried to disable SSL 3.0, TLS 1.0 but the problem persist. The PC obtained IP address from the router, I have ping on it ,also the SSID is up with open network I reset to factory default but the problem persist.
View 2 Replies
View Related
Mar 23, 2012
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
View 3 Replies
View Related
Aug 29, 2011
I do you not think the RV220W needs to have better E-mail support that the feature it supports at present?No SSL support at all. The only setting for authentication is: Login Plain or CRAM-MD5. Every mail server I use now, supports SSL as the default authentication and not CRAM or Plain, this makes the E-mail feature useless. [code]
View 1 Replies
View Related
Nov 8, 2012
I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
View 5 Replies
View Related
May 16, 2012
I have 5 public, static IP's provided by my ISP. I read on another page that to use the 2nd, 3rd, 4th and 5th IPs, I must first 'register' them by entering them on the WAN page and I must wait until I can successfully PING them from an external network. Then I can set the WAN IP back to the one I want to use to administer the router. Then I can use those other IP's on the various Access Rules or Port Forwarding pages where there is a spot to enter 'alternate WAN IP address'. I'm trying to determine if this is true because I'm having a heck of a time getting port forwarding to work. My BIOS is 1.0.3.5.
View 7 Replies
View Related
Aug 29, 2011
I am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
View 5 Replies
View Related
