I have a Belkin 690, model# F9K1002V4 that's been working great until I had to turn off and disconnect some things in order to replace my old tv stand. After I straightened out the mess of wires from everything and made sure all the connections were good all the other components including my satellite modem were working fine, but the wireless router won't reconnect. It's working fine with a cable but won't work wireless even though the blue indicator shows the actual router to be working okay. I've repeatedly reset/re-powered the router to no avail. Firmware is up to date.
For an N300 model F9K1002V4 router, how can I tell if it's transmitting in N mode? I have two newer laptops that are capable of receiving the 802.11N signal but are only receiving at 54mbps. The router is set to transmit at b/g/n rates.
I have and D-Link modem which is bridged and a PPPoAPPPoE profile set up on the RV220W for my ADSL2+ connection.I cannot for the life of me find anywhere in the routers config web pages to tell the modem to disconnect or reconnect the connetion to the ISP.The reason I want this is because I need to make sure the correct signaling is sent before the connection is stopped so that the exchange doesnt see this as a drop out and reduce our line speed to compensate.
I'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
my netgear wireless router cannot see my n300 usb adapter. it shows as working in my device manager, but the netgear router says wireless not connected. when installing the adapter it said that windows has an icon to the left of the taskbar that i can click on and ask to join a network, which it didnt. it just showed network and an option to open network and sharing center, which i did. there were no wireless networks that showed available for me to log into with the adapter
I will be setting up a new computer this weekend. I presently have a WRT54G2 wireless-G router and have configured it to an IP address that works with my AT&T(Bellsouth) broadband modem (Westell). When I reconnect it to my new computer, should I first just connect the ethernet cable to the modem as if I don't have a router (like I did for years) and then go into the instructions for setting up the router via the DVD but enter the IP address as I have it working now?
I had a wireless device connecting to my network - so I blocked it. Unfortunaletly turned out to be my daughters ipod touch. How can i reconnect it back. dont seem to be able to add device and linksys keeps blocking her connection attempts
Every two or three days I'm unable to reconnect to my wifi network when I turn on my Windows 7 laptop or Android tablet. I have to power cycle the wifi router to get the connection again. This usually happens after I haven't used either device for a day or two. The connection usually does not drop when I'm using them. Restarting the computer or the tablet does not work and using the Windows troubleshooter (or the android app for wifi issues on the tablet) also doesn't work. Both computer and tablet recognize the network and say the signal is strong but won’t connect to it. There are no physical obstructions. I have no problem with my internet connection (cable modem). The problem really seems to be with the wifi router.
Model name: Linksys E1000 Model number: E1000 Firmware version: 2.1.02 build 5 Operating system: Windows 7 SP 1 Software version: 1.3.11069.2 Connection type (WAN): DHCP
How do I update the firmware on my N wireless router with version 2000? It says there is an update, but I can't update it with the one firmware update that's available for download.
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
I recently got an E1000 router brand new V2.1 from a friend. Seems to run great, only problem both my Mac Book Pros (running snow leopard and lion) will not reconnect automatically to the wifi after waking up from sleep.
I have a 2wire Modem connected to a Cisco Wireless N Router, that is connected to another Cisco Wireless N Router. All was working well. In my absence sbc (AT&T) changed the pass word of the 2wire Modem. The 2wire has stoped communication with the Cisco Wireless N Routers. I connected am Ethernet wire to one of the ports of the 2wire, and connected it to the 2nd Cisco Wireless N Router. The signal gets to the 2nd Cisco Router. However, when I attempt to access the Internet on the CPU connected to the 2 Cisco Router, I get an error Message saying that there is a problem with the Modem and/or Router. On the available Networks selection screen I can see the connections that I want. The selection info shows connected. But when I try to connect, the I can't.
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal 2. Flashed the router with "dd-wrt.v24_mini_generic.bin" 3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
I recently replaced my old Belkin Pre-N router with a newer N router. Still, the newer one is only less older than my Pre-N Belkin router that I had sitting around but never opened and installed (F5D8231-4). Anyway, I finally decided to set it up. I was trying to log into the router to set security settings and to update the firmware but when I type the IP address into the address bar in IE or Firefox, it is partially blank. There are no functional buttons. Only the Belkin logo on a gray background with a couple of emtpy boxes where it looks like functional buttons or tabs should be. how to get to a working screen with functional buttons?
I have a wi fi capable blu ray player which works on wireless g connections, and I also have 2 computers. I have the N600 Dual Band router, and want to know if it is possible to transmit on both frequencies? I am only seeing the 2.4ghz show up for a connection.
I am trying to connect my xbox360 to my belkin surf n300 router via ethernet cable and my xbox360 cant recognize or get onto my network. i have manually entered the ip address the submask and gateway numbers, idk if they are 100% correct
I have a Belkin Surf N300 wireless Modem-Router, but cannot get it to connect to my Android phone. I can connect it to my Nexus tablet, to my desk-top and my lap-top, so I know there is nothing wrong with the router itself. Every time I try to connect the phone, it locates the network, scans, authenticates, but then says "Disabled" and the message: "Secured with WPA/WPA2 PSK" with "locked network" symbol. What does this mean? This is on the label that came with the router: "Security Type WPA/WPA2" but I don't know what to do in order to remove the lock. The phone is a Vodafone Smart Chat and I bought it specifically to be able to connect to Wi-Fi networks.
i hooked up a netgear repeater to my belkin n450db router and it shows a good connection betw router and extender and between extender and device (laptop and tv) however only a lan connection - no internet.
show me how to hook up a Belkin G Router to a symomatic Atlantics modem its already from the wall hooked up to my moms desktop and i want it also on my desktop.
I purchased a new BelkinN750 DB router on 2/12/2013. It seems to think the date is Jan. 1 1970. How can i fix this problem or should I just return it and buy another brand?
How can I configure Belkin N1 Vision Modem router to use Back to My Mac? Bcos in iCloud preferences its give me a error message "setup router for better performance"
I have a Belkin N Wireless Router Model F5D8236-4 V2. WEP security.. We have just bought a Samsung Note 10.1 Tablet. We have entered the password Key and the tablet is saying that the network is 'secured,saved' but it will not connect to the internet. We have several laptops and phones that work ok but the Samsung Note will not connect.. We have taken the Note to a friends house and it connects to the internet no problem so I know issue is with the router..