i have a wrt160Nv3 wireless router.
I had a wireless device connecting to my network - so I blocked it. Unfortunaletly turned out to be my daughters ipod touch. How can i reconnect it back. dont seem to be able to add device and linksys keeps blocking her connection attempts
I own a lynksis wag54g2 wifi router. I can establish wi-fi connection with my Android phone, Iphone 4, notebook, but after I disconnect the device from the router, I can't reconnect it again until I reboot the router. I tried some othe mobile devices with wi-fi support, the problem is the same. I tried set up different wireless security settings, tried to switch wireless mode to b, g, and mixed, installed new firmware 1.00.19, but the problem is not resolved.
View 1 Replies View RelatedI need to downgrade my WRT160n so that it will work with Xbox LIVE again. I've been told by Xbox that the only certified working firmware for my router is 3.0.02.003, But I'm using 3.0.02.004.
View 9 Replies View RelatedI bought WRT160Nv3 3 months ago . The computer is wired to the router . So I noticed 5 says ago that my download speed is slower – from 70mbps to20-30mbps . I have called the cable company and their tech support reports a good signal to the house. My firmware is up to date . I tried hard resetting the router-nothing.Plug,unplug still nothing.
View 9 Replies View RelatedMistakenly 'removed' a PC from the network. I followed the instructions on the EasyLink Advisor to add a new computer: open the .exe file that contains all the settings onto the new computer. That didn't work. But even if I removed the computer (by mistake) I don't see why when she goes to log in to the wifi account, she can't just type in the password.how to add a new computer to the wifi WRT160Nv3?
View 1 Replies View RelatedMy WRT160Nv3 appears to be working fine however, I believe there's something wrong with the setup that's making my connection unreliable. All my devices can detect the router, they can connect, but once it comes to surfing on those devices, no pages are loading up despite being connected with excellent signal strength.
View 1 Replies View RelatedI'm being kicked off my VPN connection back to the home office on occasion, using a Nortel VPN client. The logs show:
4/2/2013 9:58:26.883 [ENGS] -I-VerifyServerIsAlive: ISAKMP had traffic (after keepalive).
4/2/2013 9:58:27.383 [ENGS] -I-VerifyServerIsAlive: Set receivedData FALSE.
4/2/2013 9:58:28.555 [ENGS] -I-Protocol not recognized - message dropped.
4/2/2013 9:58:44.586 [ENGS] -I-Protocol not recognized - message dropped.
[code]....
the common fault seems to be DynamicDnsCleanup causing the trouble.(causes routing table to change, knocking down the VPN....) Is this a function occurring in the router? I can't find search results showing so.
I downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
View 2 Replies View RelatedMy WRT160Nv3 router responds to ICMP (ping), even though I have "Filter Anonymous Internet Requests" enabled. I toggled it off and on to see if that made a difference, but no luck.I am pinging it from the "outside", through the WWW, so it's not from inside the LAN..
View 6 Replies View RelatedIs it possible to add an external antenna to this WRT160Nv3 router? Some spots are just on the one bar signal level that comes and goes.
View 1 Replies View RelatedAll of a sudden, I could not connect to the Internet. I kept getting error message "Can't connect to DNS server", or similar. I have an ATT/Yahoo account, Speed stream 5360 Modem and WRT160Nv3 router. All was working well until yesterday. I was finally able to speak to an ATT Tech today, and he guided me through several troubleshooting actions and we were finally able to connect just using the modem. But when I connect the router, the network works, but I can't connect to the Internet. If I disconnect the router, I can access the Internet. None of my settings has changed. I saved router settings on my computer, and have compared them; all the same. The tech finally said it could be the blue cable from router to computer, or the router. So I'm hoping for troubleshooting before I buy another cable and/or router.
View 1 Replies View RelatedI got a new Xbox 360 Slim and he has it connected through wireless, and His older Xbox 360 connected through Ethernet. And well we would like to play some games online without some major lag. So is it possible to have an Open NAT with two Xbox's within the same network?He has a Linksys Wireless-N Broadband Router WRT160Nv3.
View 5 Replies View Relatedis there a way to display the active wireless connections?
View 2 Replies View RelatedIt worked fine for my PC's and Xbox, but I had disconnected my router for a while, plugged it back in and my xbox simply cannot receive any connection. I should also note that I use an ethernet cord (I don't use it wirelessly) and it has nothing to do with the ethernet cord (I've tried several). Using network magic, it does confirm that a connection to the game console and the router.I've looked through the forums and all of what I found, are NAT problems/issues or fixing a wireless issue, but not an issue when using an ehternet cord.
View 1 Replies View RelatedI just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
View 9 Replies View RelatedIve had the WRT160Nv3 for a while and its all been great but recently ive had some issues.Im not sure if this is my ISP but the connection to the router drops out or i lose connection to the internet.I thought the firmware was out of date so i updated to 3.03 from 3.02 and it doesnt seem to fix the problem. what it did was create new problem. now when you edit settings it says >> JAVASCRIPT; true or if i try to edit port forwording it wont save the data i enter.This was all brought to my attention when I tried to connect to my wireless and my SSID was not what i set it as, the router had some way been reset. could something of happened to the router for it to be acting all crazy.
View 1 Replies View RelatedMy router: WRT160Nv3
My Firmware Version: v3.0.02
Upgrade version: Ver.3.0.03 Build 3
I can not upgrade, always gives the same error message: Firmware upgrade failed!
WRT160Nv3 Firmware Version: v3.0.02
I've been using Linksys for years but the last two routers I have purchased have been very problematic.
- My router hasn't had this problem before. The other day I was downloading 4 games at a time from STEAM, when I got home from work I found that my router had completely gone back to factory settings. So I configured my DSL PPPoE, SSID, Wireless Security (WPA) changed the default admin PW and about 20 minutes later it was back to factory again.
I've done a "hard" reset and reconfigured and still it resets itself. What's also upsetting is this completely opens my network up to ANYONE when this happens...
So far in the past 2 days I have (now using a backup restore file) re-configured the device 10 times.
The only thing I can think of is that I just got Windows 7 the same day this started happening. I thought it could be STEAM as well so right now I have STEAM closed to see if it resets while it isn't running.
Could TOO much demand on the router cause it to completely reset itself to factory config?? Seems to me like there's a huge firmware or hardware problem here.
I have other friends and even co-workers that also have problems galore with their Linksys products...No other router it seems has as MANY issues as Linksys. Hat to say it but my next purchase most likely will not be another one of their products. This just shouldn't be happening.
today I got up and discovered that my WRT160Nv3 router has resetted to factory defaults itself, the name of the Wifi network was "linksys" and all configurations were the defaults...
That's normal? This is the first time it happens.
I have been using this router for quite some time, with a setup like.. Cable Modem ==> Vonage ==> WRT160Nv3 ==> PC. It has been working very fine for all these years (6), but now I hear static disturbances in my phone calls, and so I decided to do port forwarding for the vonage device, to minimize the noise. This device uses a static ip address of 192.168.15.1, and in the Linksys software, I am not able to use any ip addresses other than "192.168.1.*" in the port forwarding page.
View 1 Replies View RelatedI have a WRT160Nv3 router connected to a CM100 modem. I noticed that over time, perhaps a day or more, the connection speed slows. Usually, unplugging the router for a while then starting it up again restores the speed as per my cable company's speed test. I have called the cable company and their tech support reports a good signal to the house.
View 6 Replies View RelatedAccess Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedMy issue occurs on ALL of my home computers (MacBook and iMac using wi-fi) and ALL of my browsers (Safari, Firefox, Chrome).The problem:- Security Certificates: They pop up daily for Facebook mostly, but also Twitter. I will click Continue, which takes me to...- 404 Error/Page Not Found Error: After the Certificate error mentioned above, this happens. Mostly to YouTube. It will stay like this for a few hours. I've cleared cache, rebooted, etc. etc. Nothing works.- Images turn into little blue boxes with a question mark in them. **When this happens, it's an indication that a Certificate box will pop up out of the blue.- Even on Google.com, it will say: Invalid URLThe requested URL "/", is invalid.Reference #9.df260e6b.1336506889.420cf4fSo what can I do? It happens on both my Macbook Pro and iMac - both connected wirelessly to a Linksys router/cable modem. The router is Wireless-N Broadband Router WRT160Nv3 with Firmware Version: v3.0.02.
View 1 Replies View RelatedI will be setting up a new computer this weekend. I presently have a WRT54G2 wireless-G router and have configured it to an IP address that works with my AT&T(Bellsouth) broadband modem (Westell). When I reconnect it to my new computer, should I first just connect the ethernet cable to the modem as if I don't have a router (like I did for years) and then go into the instructions for setting up the router via the DVD but enter the IP address as I have it working now?
View 3 Replies View RelatedEvery two or three days I'm unable to reconnect to my wifi network when I turn on my Windows 7 laptop or Android tablet. I have to power cycle the wifi router to get the connection again. This usually happens after I haven't used either device for a day or two. The connection usually does not drop when I'm using them. Restarting the computer or the tablet does not work and using the Windows troubleshooter (or the android app for wifi issues on the tablet) also doesn't work. Both computer and tablet recognize the network and say the signal is strong but won’t connect to it. There are no physical obstructions. I have no problem with my internet connection (cable modem). The problem really seems to be with the wifi router.
Model name: Linksys E1000
Model number: E1000
Firmware version: 2.1.02 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11069.2
Connection type (WAN): DHCP
I recently got an E1000 router brand new V2.1 from a friend. Seems to run great, only problem both my Mac Book Pros (running snow leopard and lion) will not reconnect automatically to the wifi after waking up from sleep.
View 1 Replies View RelatedMy Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
I have a Linksys wireless WMP600n PCi adapter installed in my desktop PC and after recovering from standby, it does not automatically reconnect. I have to right-click on the Wireless Networks icon in the system tray then select "Repair". I would say it does this 9 times out of 10 (1 time in 10 I seem to luck out and it restores the connection automatically).
I have an Asus M4A88TD-M motherboard with 1 Gb of DDR3 RAM and I am running Windows XP Home Edition (SP3). There is only one PCi slot on this motherboard. Also, I am not using the wireless network software that shipped with the product but rather the native wireless networks application software that shipped with Windows XP. I have had this problem with the original driver that shipped with the product CD and the problem persists with the latest driver. I have not enabled Hibernation and there are no active power saving modes on the PC.I have reviewed all of the options in the Wireless 600n Properties/Advanced tab and have enabled the Continuously Awake Mode and disabled the Power Saving Mode but the problem persists.
I have two other PCs with the older Linksys wireless WMP300n PCi adapters and they do not exhibit this behaviour after recovering from standby - they reliably reconnect.
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies View RelatedMy sony blue ray player lost it's connection to my wireless lnyskis router. I can't reconnect it.
View 3 Replies View RelatedI have a Belkin 690, model# F9K1002V4 that's been working great until I had to turn off and disconnect some things in order to replace my old tv stand. After I straightened out the mess of wires from everything and made sure all the connections were good all the other components including my satellite modem were working fine, but the wireless router won't reconnect. It's working fine with a cable but won't work wireless even though the blue indicator shows the actual router to be working okay. I've repeatedly reset/re-powered the router to no avail. Firmware is up to date.
View 1 Replies View RelatedI have a 2wire Modem connected to a Cisco Wireless N Router, that is connected to another Cisco Wireless N Router. All was working well. In my absence sbc (AT&T) changed the pass word of the 2wire Modem. The 2wire has stoped communication with the Cisco Wireless N Routers. I connected am Ethernet wire to one of the ports of the 2wire, and connected it to the 2nd Cisco Wireless N Router. The signal gets to the 2nd Cisco Router. However, when I attempt to access the Internet on the CPU connected to the 2 Cisco Router, I get an error Message saying that there is a problem with the Modem and/or Router. On the available Networks selection screen I can see the connections that I want. The selection info shows connected. But when I try to connect, the I can't.
View 3 Replies View Related