I got a new Xbox 360 Slim and he has it connected through wireless, and His older Xbox 360 connected through Ethernet. And well we would like to play some games online without some major lag. So is it possible to have an Open NAT with two Xbox's within the same network?He has a Linksys Wireless-N Broadband Router WRT160Nv3.
View 5 RepliesIt worked fine for my PC's and Xbox, but I had disconnected my router for a while, plugged it back in and my xbox simply cannot receive any connection. I should also note that I use an ethernet cord (I don't use it wirelessly) and it has nothing to do with the ethernet cord (I've tried several). Using network magic, it does confirm that a connection to the game console and the router.I've looked through the forums and all of what I found, are NAT problems/issues or fixing a wireless issue, but not an issue when using an ehternet cord.
View 1 Replies View RelatedI have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedI have a WRT54G ver.5.(just did latest firmware) and a Buffalo Air Station wireless gaming adaptor.I have gone and port fowarded the UDP 88,UDP 3074,TDP 3074 I believe I have left the UPnP on (brother in law says not an issue)(?) On my XBOX 360 i have the IP & DNS set to Auto, and I get an OPEN setting on my NAT.But when I play online (Halo 3) I can't join any of my friends' parties,acting like it is STRICT. When I set up my IP & DNS to Manual and put in static IP & DNS, I run the tests and get STRICT. It seems to me that even though my NAT "says" its OPEN, it is really on STRICT.
View 4 Replies View RelatedI have a E1000 and already for the longest time I've been trying basically everything possible to get my NAT open from being strict.I've looked around and tried everything I came across including the port forwarding. The only thing different from what I have and from what I have seen is that my router's ip is 192.168.0.1 instead of 192.168.1.1 that everyone else seems to have. I don't know if that affects my NAT in any certain way either. What I can possbily do or what might be the problem as to why I can't get my NAT opened?
View 1 Replies View RelatedI'm using Cisco Connect Cloud to connect to my E4200 router. I wish to open my NAT type as currently its moderate on all games.Where the hell is the area to add the port ranges?? Is it even an option on the new connect cloud? If it is, it doesn't make it very easy to find. Would be allot easier if you had a tab/app for "Gaming/Applications" like you did previously.
View 1 Replies View Relatedhow to open my NAT Type For my xbox.
View 3 Replies View RelatedI have three xbox 360s (mine plus my son and my daughter)...I have my settings set to where when myself and my son are on our 360s our NAT type is open..
View 2 Replies View RelatedI just recently upgraded my router from the WRT160n V3 to the E3000. I had to port forward from my old 160n to get my NAT settings from Xbox Live set to OPEN. When I switched out the router to the new E3000, my Xbox Live settings went back to Medium (Moderate). I assumed this would happend since its a new router/setup.
setup my E3000 and Xbox Live so I can have my NAT settings to OPEN? I only need to setup 1 Xbox.
I Have a WRT160Nv2 and I am trying to get my nat to become unstrict for xbox live. I have tried port fowarding that has not worked. I tried this site [URL] and that didnt work(I only have one xbox 360 btw). Nothing has worked for me and every time I mess with something it screws up the internet so I have to set it up to the previous defaults. I know how to access my router I just need to know what to enable, disable, or add to the router.
View 1 Replies View Relatedi have the xbox and ps3 wired to the router and the laptop wirelessly to the router (if that makes any difference)
My router is the Linksys WAG54G2
I need to downgrade my WRT160n so that it will work with Xbox LIVE again. I've been told by Xbox that the only certified working firmware for my router is 3.0.02.003, But I'm using 3.0.02.004.
View 9 Replies View RelatedI bought WRT160Nv3 3 months ago . The computer is wired to the router . So I noticed 5 says ago that my download speed is slower – from 70mbps to20-30mbps . I have called the cable company and their tech support reports a good signal to the house. My firmware is up to date . I tried hard resetting the router-nothing.Plug,unplug still nothing.
View 9 Replies View RelatedMistakenly 'removed' a PC from the network. I followed the instructions on the EasyLink Advisor to add a new computer: open the .exe file that contains all the settings onto the new computer. That didn't work. But even if I removed the computer (by mistake) I don't see why when she goes to log in to the wifi account, she can't just type in the password.how to add a new computer to the wifi WRT160Nv3?
View 1 Replies View RelatedMy WRT160Nv3 appears to be working fine however, I believe there's something wrong with the setup that's making my connection unreliable. All my devices can detect the router, they can connect, but once it comes to surfing on those devices, no pages are loading up despite being connected with excellent signal strength.
View 1 Replies View RelatedI'm being kicked off my VPN connection back to the home office on occasion, using a Nortel VPN client. The logs show:
4/2/2013 9:58:26.883 [ENGS] -I-VerifyServerIsAlive: ISAKMP had traffic (after keepalive).
4/2/2013 9:58:27.383 [ENGS] -I-VerifyServerIsAlive: Set receivedData FALSE.
4/2/2013 9:58:28.555 [ENGS] -I-Protocol not recognized - message dropped.
4/2/2013 9:58:44.586 [ENGS] -I-Protocol not recognized - message dropped.
[code]....
the common fault seems to be DynamicDnsCleanup causing the trouble.(causes routing table to change, knocking down the VPN....) Is this a function occurring in the router? I can't find search results showing so.
I downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
View 2 Replies View Relatedi have a wrt160Nv3 wireless router.
I had a wireless device connecting to my network - so I blocked it. Unfortunaletly turned out to be my daughters ipod touch. How can i reconnect it back. dont seem to be able to add device and linksys keeps blocking her connection attempts
My WRT160Nv3 router responds to ICMP (ping), even though I have "Filter Anonymous Internet Requests" enabled. I toggled it off and on to see if that made a difference, but no luck.I am pinging it from the "outside", through the WWW, so it's not from inside the LAN..
View 6 Replies View RelatedIs it possible to add an external antenna to this WRT160Nv3 router? Some spots are just on the one bar signal level that comes and goes.
View 1 Replies View RelatedAll of a sudden, I could not connect to the Internet. I kept getting error message "Can't connect to DNS server", or similar. I have an ATT/Yahoo account, Speed stream 5360 Modem and WRT160Nv3 router. All was working well until yesterday. I was finally able to speak to an ATT Tech today, and he guided me through several troubleshooting actions and we were finally able to connect just using the modem. But when I connect the router, the network works, but I can't connect to the Internet. If I disconnect the router, I can access the Internet. None of my settings has changed. I saved router settings on my computer, and have compared them; all the same. The tech finally said it could be the blue cable from router to computer, or the router. So I'm hoping for troubleshooting before I buy another cable and/or router.
View 1 Replies View Relatedis there a way to display the active wireless connections?
View 2 Replies View RelatedI just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
View 9 Replies View RelatedIve had the WRT160Nv3 for a while and its all been great but recently ive had some issues.Im not sure if this is my ISP but the connection to the router drops out or i lose connection to the internet.I thought the firmware was out of date so i updated to 3.03 from 3.02 and it doesnt seem to fix the problem. what it did was create new problem. now when you edit settings it says >> JAVASCRIPT; true or if i try to edit port forwording it wont save the data i enter.This was all brought to my attention when I tried to connect to my wireless and my SSID was not what i set it as, the router had some way been reset. could something of happened to the router for it to be acting all crazy.
View 1 Replies View RelatedMy router: WRT160Nv3
My Firmware Version: v3.0.02
Upgrade version: Ver.3.0.03 Build 3
I can not upgrade, always gives the same error message: Firmware upgrade failed!
WRT160Nv3 Firmware Version: v3.0.02
I've been using Linksys for years but the last two routers I have purchased have been very problematic.
- My router hasn't had this problem before. The other day I was downloading 4 games at a time from STEAM, when I got home from work I found that my router had completely gone back to factory settings. So I configured my DSL PPPoE, SSID, Wireless Security (WPA) changed the default admin PW and about 20 minutes later it was back to factory again.
I've done a "hard" reset and reconfigured and still it resets itself. What's also upsetting is this completely opens my network up to ANYONE when this happens...
So far in the past 2 days I have (now using a backup restore file) re-configured the device 10 times.
The only thing I can think of is that I just got Windows 7 the same day this started happening. I thought it could be STEAM as well so right now I have STEAM closed to see if it resets while it isn't running.
Could TOO much demand on the router cause it to completely reset itself to factory config?? Seems to me like there's a huge firmware or hardware problem here.
I have other friends and even co-workers that also have problems galore with their Linksys products...No other router it seems has as MANY issues as Linksys. Hat to say it but my next purchase most likely will not be another one of their products. This just shouldn't be happening.
today I got up and discovered that my WRT160Nv3 router has resetted to factory defaults itself, the name of the Wifi network was "linksys" and all configurations were the defaults...
That's normal? This is the first time it happens.
I have been using this router for quite some time, with a setup like.. Cable Modem ==> Vonage ==> WRT160Nv3 ==> PC. It has been working very fine for all these years (6), but now I hear static disturbances in my phone calls, and so I decided to do port forwarding for the vonage device, to minimize the noise. This device uses a static ip address of 192.168.15.1, and in the Linksys software, I am not able to use any ip addresses other than "192.168.1.*" in the port forwarding page.
View 1 Replies View RelatedI have a WRT160Nv3 router connected to a CM100 modem. I noticed that over time, perhaps a day or more, the connection speed slows. Usually, unplugging the router for a while then starting it up again restores the speed as per my cable company's speed test. I have called the cable company and their tech support reports a good signal to the house.
View 6 Replies View RelatedAccess Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedMy issue occurs on ALL of my home computers (MacBook and iMac using wi-fi) and ALL of my browsers (Safari, Firefox, Chrome).The problem:- Security Certificates: They pop up daily for Facebook mostly, but also Twitter. I will click Continue, which takes me to...- 404 Error/Page Not Found Error: After the Certificate error mentioned above, this happens. Mostly to YouTube. It will stay like this for a few hours. I've cleared cache, rebooted, etc. etc. Nothing works.- Images turn into little blue boxes with a question mark in them. **When this happens, it's an indication that a Certificate box will pop up out of the blue.- Even on Google.com, it will say: Invalid URLThe requested URL "/", is invalid.Reference #9.df260e6b.1336506889.420cf4fSo what can I do? It happens on both my Macbook Pro and iMac - both connected wirelessly to a Linksys router/cable modem. The router is Wireless-N Broadband Router WRT160Nv3 with Firmware Version: v3.0.02.
View 1 Replies View RelatedI am having BSNL broadband & netgear router. Some of the sites are not opening like [URL] many more?
View 4 Replies View Related