My WRT160Nv3 router responds to ICMP (ping), even though I have "Filter Anonymous Internet Requests" enabled. I toggled it off and on to see if that made a difference, but no luck.I am pinging it from the "outside", through the WWW, so it's not from inside the LAN..
View 6 Replies
I need to downgrade my WRT160n so that it will work with Xbox LIVE again. I've been told by Xbox that the only certified working firmware for my router is 3.0.02.003, But I'm using 3.0.02.004.
View 9 Replies View RelatedI bought WRT160Nv3 3 months ago . The computer is wired to the router . So I noticed 5 says ago that my download speed is slower – from 70mbps to20-30mbps . I have called the cable company and their tech support reports a good signal to the house. My firmware is up to date . I tried hard resetting the router-nothing.Plug,unplug still nothing.
View 9 Replies View RelatedMistakenly 'removed' a PC from the network. I followed the instructions on the EasyLink Advisor to add a new computer: open the .exe file that contains all the settings onto the new computer. That didn't work. But even if I removed the computer (by mistake) I don't see why when she goes to log in to the wifi account, she can't just type in the password.how to add a new computer to the wifi WRT160Nv3?
View 1 Replies View RelatedMy WRT160Nv3 appears to be working fine however, I believe there's something wrong with the setup that's making my connection unreliable. All my devices can detect the router, they can connect, but once it comes to surfing on those devices, no pages are loading up despite being connected with excellent signal strength.
View 1 Replies View RelatedI'm being kicked off my VPN connection back to the home office on occasion, using a Nortel VPN client. The logs show:
4/2/2013 9:58:26.883 [ENGS] -I-VerifyServerIsAlive: ISAKMP had traffic (after keepalive).
4/2/2013 9:58:27.383 [ENGS] -I-VerifyServerIsAlive: Set receivedData FALSE.
4/2/2013 9:58:28.555 [ENGS] -I-Protocol not recognized - message dropped.
4/2/2013 9:58:44.586 [ENGS] -I-Protocol not recognized - message dropped.
[code]....
the common fault seems to be DynamicDnsCleanup causing the trouble.(causes routing table to change, knocking down the VPN....) Is this a function occurring in the router? I can't find search results showing so.
I downloaded and upgraded my router to the 3.0.03 firmware. Downloaded the bin file, saved the config, upgraded firmware, reset router and restored configuration. Everything went ok but router still shows 3.0.02 firmware. ?I have a camera system on the network routed through two opened ports on the router. Everything works fine.The camera system does not store any logs relative to remote access. I would like to log any incoming traffic on the camera open ports. Is there a way to do this on this router?
View 2 Replies View Relatedi have a wrt160Nv3 wireless router.
I had a wireless device connecting to my network - so I blocked it. Unfortunaletly turned out to be my daughters ipod touch. How can i reconnect it back. dont seem to be able to add device and linksys keeps blocking her connection attempts
Is it possible to add an external antenna to this WRT160Nv3 router? Some spots are just on the one bar signal level that comes and goes.
View 1 Replies View RelatedAll of a sudden, I could not connect to the Internet. I kept getting error message "Can't connect to DNS server", or similar. I have an ATT/Yahoo account, Speed stream 5360 Modem and WRT160Nv3 router. All was working well until yesterday. I was finally able to speak to an ATT Tech today, and he guided me through several troubleshooting actions and we were finally able to connect just using the modem. But when I connect the router, the network works, but I can't connect to the Internet. If I disconnect the router, I can access the Internet. None of my settings has changed. I saved router settings on my computer, and have compared them; all the same. The tech finally said it could be the blue cable from router to computer, or the router. So I'm hoping for troubleshooting before I buy another cable and/or router.
View 1 Replies View RelatedI got a new Xbox 360 Slim and he has it connected through wireless, and His older Xbox 360 connected through Ethernet. And well we would like to play some games online without some major lag. So is it possible to have an Open NAT with two Xbox's within the same network?He has a Linksys Wireless-N Broadband Router WRT160Nv3.
View 5 Replies View Relatedis there a way to display the active wireless connections?
View 2 Replies View RelatedIt worked fine for my PC's and Xbox, but I had disconnected my router for a while, plugged it back in and my xbox simply cannot receive any connection. I should also note that I use an ethernet cord (I don't use it wirelessly) and it has nothing to do with the ethernet cord (I've tried several). Using network magic, it does confirm that a connection to the game console and the router.I've looked through the forums and all of what I found, are NAT problems/issues or fixing a wireless issue, but not an issue when using an ehternet cord.
View 1 Replies View RelatedI just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
View 9 Replies View RelatedIve had the WRT160Nv3 for a while and its all been great but recently ive had some issues.Im not sure if this is my ISP but the connection to the router drops out or i lose connection to the internet.I thought the firmware was out of date so i updated to 3.03 from 3.02 and it doesnt seem to fix the problem. what it did was create new problem. now when you edit settings it says >> JAVASCRIPT; true or if i try to edit port forwording it wont save the data i enter.This was all brought to my attention when I tried to connect to my wireless and my SSID was not what i set it as, the router had some way been reset. could something of happened to the router for it to be acting all crazy.
View 1 Replies View RelatedMy router: WRT160Nv3
My Firmware Version: v3.0.02
Upgrade version: Ver.3.0.03 Build 3
I can not upgrade, always gives the same error message: Firmware upgrade failed!
WRT160Nv3 Firmware Version: v3.0.02
I've been using Linksys for years but the last two routers I have purchased have been very problematic.
- My router hasn't had this problem before. The other day I was downloading 4 games at a time from STEAM, when I got home from work I found that my router had completely gone back to factory settings. So I configured my DSL PPPoE, SSID, Wireless Security (WPA) changed the default admin PW and about 20 minutes later it was back to factory again.
I've done a "hard" reset and reconfigured and still it resets itself. What's also upsetting is this completely opens my network up to ANYONE when this happens...
So far in the past 2 days I have (now using a backup restore file) re-configured the device 10 times.
The only thing I can think of is that I just got Windows 7 the same day this started happening. I thought it could be STEAM as well so right now I have STEAM closed to see if it resets while it isn't running.
Could TOO much demand on the router cause it to completely reset itself to factory config?? Seems to me like there's a huge firmware or hardware problem here.
I have other friends and even co-workers that also have problems galore with their Linksys products...No other router it seems has as MANY issues as Linksys. Hat to say it but my next purchase most likely will not be another one of their products. This just shouldn't be happening.
today I got up and discovered that my WRT160Nv3 router has resetted to factory defaults itself, the name of the Wifi network was "linksys" and all configurations were the defaults...
That's normal? This is the first time it happens.
I have been using this router for quite some time, with a setup like.. Cable Modem ==> Vonage ==> WRT160Nv3 ==> PC. It has been working very fine for all these years (6), but now I hear static disturbances in my phone calls, and so I decided to do port forwarding for the vonage device, to minimize the noise. This device uses a static ip address of 192.168.15.1, and in the Linksys software, I am not able to use any ip addresses other than "192.168.1.*" in the port forwarding page.
View 1 Replies View RelatedI have a WRT160Nv3 router connected to a CM100 modem. I noticed that over time, perhaps a day or more, the connection speed slows. Usually, unplugging the router for a while then starting it up again restores the speed as per my cable company's speed test. I have called the cable company and their tech support reports a good signal to the house.
View 6 Replies View RelatedAccess Restrictions option does not exist on my WRT160Nv3 Broadband Router Setup Page and I need to use that option.
View 2 Replies View RelatedPossible to set up access restrictions to Allow only specific websites?
View 1 Replies View RelatedMy issue occurs on ALL of my home computers (MacBook and iMac using wi-fi) and ALL of my browsers (Safari, Firefox, Chrome).The problem:- Security Certificates: They pop up daily for Facebook mostly, but also Twitter. I will click Continue, which takes me to...- 404 Error/Page Not Found Error: After the Certificate error mentioned above, this happens. Mostly to YouTube. It will stay like this for a few hours. I've cleared cache, rebooted, etc. etc. Nothing works.- Images turn into little blue boxes with a question mark in them. **When this happens, it's an indication that a Certificate box will pop up out of the blue.- Even on Google.com, it will say: Invalid URLThe requested URL "/", is invalid.Reference #9.df260e6b.1336506889.420cf4fSo what can I do? It happens on both my Macbook Pro and iMac - both connected wirelessly to a Linksys router/cable modem. The router is Wireless-N Broadband Router WRT160Nv3 with Firmware Version: v3.0.02.
View 1 Replies View RelatedWe have multiple CSS 11500 clusters. We have found that on all of them, if you try to open a session on any port to an IP address on the backend of the CSS, the CSS will complete the SYN-ACK-ACK session with the client. This happens regardless of whether there is something on that IP address or not.
Coming from any IP, if I try to telnet to ANY IP on the 10.2.2.0 subnet (whether or not there is an actual server on that IP) on any port (whether or not that port is open or not), the CSS will complete the initial connection. I have verified this using telnet to numerous ports and viewing the transaction in a packet capture.
Is there any way to shut this off? This is causing some licensing issues for our security folks that use a vulnerability scanner licensed on number of IP addresses.
I have a WRVS4400N router in a remote office. I have connectivity to the office and computers there. But the web interface for the router is failing to come up. This happens once every few days or so. Is there any utility or something that I can use to remotely reset the router without making use of the webinterface or having physical access to the router?
View 4 Replies View RelatedI need to type the WPA key for my wireless network on a PS3. I just can't find the 63 digit code anywhere. I've already logged on the router's page by typing the admin and passcode... there's absolute no information on the WPA Key digits
View 1 Replies View RelatedI recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
I am able to connect to corporate VPN with no issues when connecting directly to ISP modem. When I try to complete the same VPN connection via a Wireless Router (Linksys WRT160Nv3) i get the following message: "Network error. Unable to look up host names"I have tried connecting and it will initially connect, but 15-30 seconds it will drop and connection can't be re-established.Is there a setting on the Linksys WRT160Nv3 that needs to be changed?
View 3 Replies View RelatedI am trying to connect a second desktop computer running Windows 7 to a linksys wrt160nv3 Router. The router is currently connected via Ethernet cable to a desktop running Windows XP. I tried to connect the Windows 7 computer to the router via an Ethernet cable, but that does not seem to work.
View 1 Replies View Relatedhow to setup a cellular internet sharing?
I'm using 'Cisco Linksys WRT160Nv3' router. Here is my PowerPoint-drawn diagram if you want to know how I want it to work...
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies View RelatedI previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View Related