The firewall on my RVS4000 appears to hang when ever I use Netflix. If I disable the firewall and re-enable it it works for a while and then stops again. My IP address is in the Approved Client IP Addresses so it is excluded from the URL filtering and Web reputation rules.
View 5 RepliesWe have a newly-purchased RVS4000 v2 with firmware v2.0.2.7. Its intended role is as a gateway between our local network of wired workstations and a Cisco 2800 series Integrated Services Router, which is at the receiving end of our T1 line. It is configured with static IPs on both the LAN and the WAN side. It does NOT serve DHCP for the LAN. Ever since I installed it, I have had repeated complaints from users of Vista and Win7 workstations that they lose internet connectivity about every 20 - 30 minutes or so. The only solution is to unplug the workstation's CAT5 cable, count to 30, and plug it back in. Then everything's hunky dory for another 20 - 30 minutes. Meanwhile, all our Windows XP and Linux workstations enjoy uninterrupted internet access. The router/gateway we replaced (a DLink DIR-130) never had this problem.
View 4 Replies View RelatedWhen watching Netflix, I can get 5 to 15 minutes of a movie no problem. Then I will get an error message:Cannot connect to Netflix. try again later. If the problem persists
- try again
- exit
Then I can watch a few more minutes and it stops again. And again, and again......I have cable inernet service (Brighthouse Communications), with the E42000 connected to the cable modem. Then I have a Panasonic WiFi adaptor (DY-WL10) plugged into a USB port on my Panasonic Viera TV. I have the latest firmware on the router (1.3.03, build 14).I have done the routine of re-cycling the network by re-setting the router (and re-setting it up) and the modem.The chat session guys had me do the following:
1) Uncheck “Filter anonymous request”.
2) Click on Setup Tab - Here you will see MTU.
3) Select Manual & set the size to 1364
4) On Wireless tab, clicked on manual, change the Channel for the 2.4 Ghz network to 9.
5) When we tried it on the 5Ghz wireless they had me set the channel Width to 40MHz Only, and set to channel – 161
I also tried setting up port range forwarding. He knew the port information, and walked me through it.I have re-set the router to factory default settings, re-installed the software, and tried the previous steps twice more (except the port forwarding, because without my friend, I am not sure exactly how) I know enough to not have multiple WiFi devices going at the same time while trying to watch Netflix, but I know that I get good WiFi download speed tests at the location of the TV with an iPad (3.6 MBPS).I have done troubleshooting on the internet service. It has a good, strong continuous uninterrupted speed.I have tried this on two different TVs (similar Panasonic models, bit with the same WiFi adaptor). Problem persists on both TVs.I tested it with a 50’ LAN Cable running from the router to the TV. Netflix worked when wired!Next test I want to do is to stream Netflix on the iPad, right at the TV and ensure that works.To me, this seems like a wireless router setting issue or an issue with the Network Adaptor, or an issue of communicating between the Router and the adaptor.
My new RVS4000 (2.0.2.7) connects the WAN via PPoE with dynamic IP which is held at DynDNS and normally I see the RVS4000 via a router-to-router-VPN. That works fine so far, but every "some" days the router looses WAN connection (and with ist VPN). When this happens, last DynDNS-update is hours ago, so it didn`t reconnect. Looking on the routers site, the LAN is fully functional for clients that have got their DHCP-Information. New clients don`t get DHCP-Info (IP-address, DNS), both do not have internet access. The router`s WAN-summary shows, that it thinks to be "CONNECTED" but with empty WAN-IP and DNS entries. Klicking "DISCONNECT" and then "CONNECT" again solves the problem so far. The loss of connection is not the periodic break from the IPC, which is correctly identified and reconnected as configured. I wanted to trace the problem with the log, but there is also a bug. It stops logging at some time completely - neither email-log nor local log, so I never happend to be lucky to hit the point of loss of connection. Also the local log provides a first and next pages, but the next pages are always empty - not really useful.
View 3 Replies View RelatedWe have two RVS4000 at both ends of a VPN tunnel. The tunnel is up and runs fine. I can ping the two servers at the main office end of the tunnel, and cconnect to the resources of both servers. However, one of the servers, the terminal server, is unreachable via RDP. The other server can be reached via RDP for administrative purposes just fine, but the terminal server cannot be reached. There is only one difference that I can think of. The terminal server is reachable from the outside world via a redirected forwarded port on the RVS4000 at the main office.
The current firmware version is V2.0.0.3 at both ends. Is this a known anomaly for this revision of firmware?
Just recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?
View 4 Replies View RelatedI've recently upgraded from a 512k adsl connection to a 16mb fiber optic connection.Whereas I never had a problem previously, my rvs4000 slows to a crawl once or twice per week. The only solution seems to be to cycle the power since the admin interface freezes. I also have to cycle the power on my two wireless ap to get them back up.I believe I have the latest firmware, is this a common problem on a faster connection?
View 1 Replies View RelatedThe local router is behind a fiber firewall/router; the rvs4000's ext ip is thus 192.168.1.2, not visible from the net. The firewall/router is a dyn ip, with a dyn dns name mapping to it. The remote (some NetGear thing) is also dyn dns, but it is not behind a firewall.
I want to cook a vpn from the local lan subnet to the remote lan subnet.
It worked fine when both ends were NetGear.
I think it would be ok if somehow I could thell the rvs4000 that the local Security Gateway Type be just FQDN; it can't be IP+FQDN because the remote end doesn't know anything about that kind of thing; it can do IP or FQDN or a couple other confusing things.
Recently i bought a Cisco RVS4000, upgraded the firmware to latest stable release (Firmware Version: V2.0.2.7) and started configuring it.Yesterday i found out that as the dsl connection drops (i'm using PPPoE with an ethernet ADSL Modem) the product stops logging, both locally and to an external configured syslog (which resides on a linux box over the LAN).
View 3 Replies View RelatedI have a RVS4000 and I am going to configure vlan in the near future. Among all other configurations sent by the internet provider company is this one :
Firewall NAT :
from x.x.2.0/24 to 0.0.0.0/24 should be NAT
from x.x.2.0/24 to x.x.0.0/21 should not be NAT
From all the other configurations, this one is not clear to me. Can this configuration be done on a RVS4000 and where can it be done.
RVS4000 has default firewall rule from ANY WAN -> to ANY LAN with status Allowed. Should that be denied by default, like in RV042 or RVL200?
View 7 Replies View RelatedI am trying to access a device behind my firewall that needs to use port 9000. I have completed the single port forwarding page with the exterior and internal port but I cannot access the device from outside the firewall. Yes I did check the "enabled" box
View 8 Replies View RelatedI'm using two WRV210 Linksys Cisco Routers to create a tunnel between two places with a pppoe adsl internet connection.I made several tests with new 2.xxx and old 1.7xx firmware, and nothing changes.Try to reset to factory defaults, and nothing changes.I have two problems:
1) The router crashes after a time working, usualy around 24 hours, sometimes more, sometimes less. The lights still flashing, but nothing happens, no VPN traffic and no ping response from the router, and of course, no internet access. I could see just that the router works a bit hot, but, I think that is normal.
2) The VPN IPSEC was configured, and both configurations are identical. All value are the same, I am using the dyndns service. So, the VPN quickly connects and I can ping and access remote computers. Windows Folders, VNC, IT'S REALLY WORKS FULL. WORKS REALLY FINE. PERFECT.
BUT, when the router crashes, as I've told on problem 01, after remove the power cord and insert ir again, the VPN don't reconnect.On log's, I could see that it's say that has no preshared key. [code] But, it worked before. Nothing changes, nothing, the router just restarts. No configuration was lost, (I checked the VPN IPSEC TAB), but says that have no preshared key,The unique way to restablish the connection is go on the VPN IPSEC TAB, and change symetrical any configuration, as change MAIN MODE to AGGRESSIVE on both routers.So, now are as MAIN. Tomorow probably it will crash, so, I will have to restart both routers, and change to AGGRESSIVE. So, when it happens again, i will have to back to MAIN.
When I power on our ASA 5510 it just hangs on "Launching BootLoader...".
I've managed to get into ROMMON before it attempts to launch the bootloader and tried to restore an ASA image but it said disk0: failed to mount.I've copied the console output but am not sure if it is useful to diagnose the problem or not (and is quite long)
If I have the IP ACL firewall enabled in my RVS4000 I have trouble connecting to specific websites and also connecting to Apple's update servers. The problem appears to be that the firewall is blocking incoming data to the ephemeral ports even when they are allowed in the firewall rules. I've also tried port forwarding rules but the only thing that resolves the problem is to disable the firewall entirely, which is not the desired resolution. The firmware version is 2.0.27.
View 11 Replies View RelatedI have problem with RVS4000 fw 1.3.3.5. When you switch the status of IPS function (turn on or turn off), firewall rules don´t work from that moment until you restart the router!
View 2 Replies View RelatedI have multiple RVS4000 in a VPN ipsec Site to site to a ASA5505. The connection is fine most of the time.But the VPN connection randomly drops, not all the devices at once but they all do at a different time.
View 1 Replies View Relatedi have been having issues with my internet for months now, my router just randomly loses its internet connection over and over everyday. I used to have slow internet with verizon so i changed to comcast and after i changed to comcast this problem started, when i called comcast they said that it has to be interference from an unknown source. I have a Wireless-N 150 Router model WNR1000v2 and it came with a modem. Things i have tried are changing my security to WPA2-PSK[AES] which it saiid would increase my connectivity..did not, i have changed my channel also didnt solve the problem. I have had this problem with 2 different routers and modems so far. And i have 2 desktops and 2 laptops connected to this. 1 desktop is hooked straight into the router and the other 3 are wireless.
View 5 Replies View RelatedI got no code, and as a matter of fact have no Internet connectivity to my Bluray player. When I go to my Bluray setting tab and run a network test the MAC Address checks out but fails when it gets to IP Address. My Bluray is plugged directly into my router and it still shows no Internet connection between the two, even though my x-box 360 has no problem nor does my computer. When looking at my network settings the IP Addresss boxes all have numbers in them, the Subnet Mask boxes two of four boxes have numbers the others are zeros, the Gateway boxes are all zeros, and the DNS Server boxes are all zeros. I read many of the posts in this forum and all problems seem pretty similar to mine.
View 4 Replies View RelatedI bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload Details About Router & Connection,Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.
View 1 Replies View RelatedFor the past few months my internet connection will randomly drop for about 5-10 seconds when someone else connects to the network. I am using a wired Ethernet connection and as said when someone connects either via WiFi or also through a wired connection, the internet for me will drop as soon as the device is connected, and then randomly every 20 minutes or so thereafter. I should also mention that rarely the connection will just drop for again, 5-10 seconds even when nobody else is connected.I tried my computer at someone else's house using their router and it worked fine, no disconnects at all.
View 1 Replies View RelatedI have two wifi routers which I have connected together with an ethernet cable to extend coverage across my house. The ethernet cable is connected to a LAN port on the first router and the internet port of the second router. This works fine and creates a second network that I can connect to the net on. The problem iseemingly randomly, about every 15 minutes, the second router will lose internet connection. My laptops and phone still stay connected to it, but windows lists it as having no internet connection. If I then wait a couple of minutes and reconnect, internet will be working again.
View 4 Replies View RelatedI have a Cisco ASA 5505 - 50 VPN edition. I have baffling network issues that I have not been able to pinpoint and I recently started to think it may have something to do with my ASA. I'm a network administrator and I have a Cisco ASA 5505 in my home network so I can learn how to manage Cisco ASA's and utilize the Easy VPN feature so I have a always on VPN connection into work to log into servers, etc. I've been using the ASA for almost 6 months with the EasyVPN feature with no issues. My ISP is Comcast.
Within the last week my connections have been randomly dropping for about 20 seconds and then reconnecting. I have two computers on the network that have a direct ethernet run to the switch ports on the back of the ASA. When the connection drops, I see my LAN icons completely lose connectively (yellow exclamation warning) then after 20 seconds, reconnect. This is very random. I was able to get it to happen every time I connected to XBOX live and play a online game. It would almost on cue drop after 30 minutes of online gamming. Here are the steps I have taken:
1. Replaced 10/100 switch to a brand new 10/100/1000 switch from computer run in my office to the ASA.
no joy
2. I upgraded the ASA to the most recent firmware: ASA Version 8.4, ASDM Version 6.4
no joy
3. I had an ethernet run under my carpet to the office, I started to think that maybe one of the cables had an issue after walking on it and vacumming causing a short. I removed all the ethernet under the carpet and installed power line over ethernet adapter from the ASA to my office.
no joy
4. I checked both computers on the network for viruses. All computers came back clean after scanning wth Malwarebytes and SuperAntispyware.
5. I've watched the logs on the ASA as the LAN connection drops and I don't see error messages to troubleshoot this issue.
The only thing left to replace is the Comcast modem or the Cisco ASA. The Comcast modem is newer and only about 1 year old (rented from Comcast). Since my actual LAN connection drops and I lose connectively I believe there may be some issue with the ASA or the ASA switch ports or some sort of internal hardware issue on the ASA.
* ADSL modem connected to internet
* WiFi router (Netgear WPN824v2) connected to ADSL modem
* CPU, iPhone and iPad connected to router, CPU wired connection.Everything has worked like a charm up until a couple of days ago. Now the link between the router WAN port and the modem randomly drops. Stays dropped for 1-3 secs and then connect again. When its really bad this happens with 5-10 secs intervall. This made it impossible to use the network from any of the devices.If I disconnect the CPU from the router and connect it direcly to the modem and change the IP settings to match the modem network the CPU connects without errors to the internet, iPad and iPhone connected to the router keeps having problems.Restarting the router does not change anything and it seems to be more frequent errors during heavy load hours, in the morning I have almost no problems at all, in the evenings I cant almost use the wireless devices (CPU works fine as its now connected directly to the modem not through the router).I havent changed a setting in the last year, it just came right out of the blue.I have hard reset both the modem and the router and reconfigured them (that I dont want to do again as I have some virtual servers, port forwards, port triggers and so on :P).As it came right out of the blue without me changing anything on any device and as it seems to be more frequent during heavy load hours I'm suspecting that the ISP is involved, but how can they be (it works fine with devices connected straight to the modem)?
FSD 7632-4 Router.Have this 2006 router which has started dropping the connection and/or slowing it down intermittently. Before I replace it, would like to update the firmware. Have downloaded the update but cannot log-in on the setup utility page as I cannot remeber my password (apparently it is not set to blank!).
View 1 Replies View RelatedOne of our hospitals keeps reporting that their internet is going out for a while than comes back up, sometimes they even have to reset the ISP modem for this it to work again. I upgraded and switched ISP to Time Warner Cable and figured it would essentially solve the issue, but there are still reports of internet outage and our new ISP has confirmed multiple times that their end is still up. Our ASA 5505 was configured by a previous employee, but when looking at the running config I noticed that the Interface for our ISP is NOT set to Duplex Full and Speed 100.
interface Ethernet0/5
switchport access vlan 2
One of our hospitals keeps reporting that their internet is going out for a while than comes back up, sometimes they even have to reset the ISP modem for this it to work again. I upgraded and switched ISP to Time Warner Cable and figured it would esentially solve the issue, but there are still reports of internet outage and our new ISP has confirmed multiple times that their end is still up. Our ASA 5505 was configured by a previous employee, but when looking at the running config I noticed that the Interface for our ISP is NOT set to Duplex Full and Speed 100.
interface Ethernet0/5
switchport access vlan 2
I have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View RelatedI am a novice with networks but do have a fair understanding of networks. I have a small business network, utilizing a RVS4000 router (Firmware V2.0.27)I am attempting to set up firewall rules to block certain web sites at certain times.I have successfully set up rules using source and destination ranges, to deny service 24 hours a day everyday.
However and here is the problem when I attempt to edit any of the rules (I want to change the time to certain hours of the day) it allows me to edit the rule but when I attempt to save I get an error message up saying there are invalid characters and it will not save the changes?create the whole thing with the changes I want it works fine, is this a known bug?
I’ve been using a Cisco ASA 5505 Security Plus bundle for two years now without any problems. My previous Internet Service Provider was routing the external IP I was leasing directly through to my internal network without NAT which my ASA 5505 was working well with. Thus, I had configured my 5505 to provide NAT to my inside network which includes two subnets one for my workstations and internal "private" resources and a DMZ to provide access to my webserver, email server and two domain name servers; but restrict access to my internal; resources. i recently changed my ISP to Verizon FiOS (which is providing me with 25 Mb bandwidth at a fraction of the cost of my old T1) which is set up to provide 5 Static externally facing IP numbers for my email, webserver and name servers;. The problem is the Verizon router doesn’t support my use of the ASA Appliance (at least not the way it is currently configured. Verizon recommend I purchase a business class router and use it in place of the one they provided with my installation. With this in mind, I bought a Cisco RVS4000. I have configured it to use the primary external IP number and have internet access; however, the new router is providing NAT addressing which the ASA is in conflict with (they are both using the same NAT IP range). I'm assuming the ASA 5505 is expecting to have access to the external IP addressed (since that is what it was getting before) and NOT NAT address. How to configure the new router to either provide access to the five static external “real world” IP to my Cisco ASA Firewall. However, I just need to get my ASA 5505 back in the loop and would prefer to do this rather than go back to the Verizon router combined with a low end firewall. So, my questions are: Does the ASA 5505 expect real world External IP numbers? Or can it work with NAT addresses being fed to it from the router? And, if so, how do I configure the access rules and other items which are currently mapping to external numbers?
View 27 Replies View RelatedIve set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies View RelatedI have an RVS4000 running V2.0.2.7 firmware that gives me an "Invalid Character(s) Found" error message when I try to edit an existing ACL.
I'm trying to deploy 57 of these routers and would like to be able to use a pre-built config dropped onto each router.
I initially planned on editing the exported config with a find&replace for my local LAN addresses. Since that didn't work the next reasonable solution would be to edit the ACL list (much more tedious, but still better than hand-entering every ACL on all 57 devices).
when this bug will be addressed? Alternatively, if there is an offline configuration editing tool I would be one happy camper to have it!
I have an RVS4000, not installed. How can I tell from the unit or the packaging that it is a v1 or a v2, without installing and switching it on (which I don't want to do now) ? Are v1 branded Linsys and v2 Cisco ? Can you tell from the date on the package (mine says copyright 2011) ?
View 1 Replies View Related