I was wondering if anyone has seen their VPN User Connection Status Table empty even though you know for sure clients are connected? I connect with my iPhone to the PPTP VPN successfully and it works fine but there's no entry for the connection on the VPN User Connection Status Table. Is that normal? Does the router only collect data about Windows clients?
View 3 Repliesget a status on Mac Lion and/or Windows 7 64-bit SSL VPN support for the RV220W? QuickVPN (for Windows 7 64-bit users) and IPSecuritas (for Mac Lion users) are our current workarounds, but for folks that use/own their own equipment we prefer SSL VPN. This is why we retired our WRVS4400N v2 for the RV220W.
View 3 Replies View RelatedI have the RV220W and we are mainly using PPTP for VPN access. I can not add more than 9 PPTP VPN user acounts. When I go to add a tenth account the interface just hangs and stops responding. I can delete a user and then add another user and this works fine. I can also add other types of VPN users.
View 4 Replies View RelatedI have created 7 QuickVPN users on router and on QuickVPN client. They all work except two. Have deleted and reinstalled on router and in QuickVPN to no avail. Changing the user name by one letter works (eg user NameVPN doesn't work, but NameVP does). Somehow router (I think) is not releasing user credentials/policies (which seems to agree with log). I have rebooted router.
View 1 Replies View RelatedI just bought a RV220W for my small company. I have read everywhere that this model come with 25 license for QuickVPN/IPsec.But when I tried to create all my account I had a bad surprise. The firmware tell me that the maximum number of user that I can create is 10! I dont see anywhere in the firmware where I can upgrade for another licence. I have the last firmware.
View 7 Replies View RelatedI've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).
View 1 Replies View RelatedI have seen some discussion in the forums regarding user defined groups being empty in LMS 4.0 but not 4.1. I am having this issue in 4.1. Under User Defined groups, I have created 2 logical groups named "Physical Location" and "Switches". These do not contain any actual devices, they are just containers for other groups. Under the Physical Location logical group I have created 2 other groups, Acuna and Hampton. Under the Switches group I have also created 2 groups, HDM and HHC. The criterion for the Physical Location group is based on the first 3 characters of the hostname:
Device.System.Name startswith "hdm"
The criterion for the Switches group is based on the value of a user defined field, Admin_responsibility:
Device.Admin_responsibility equals "HDM"
The Physical Location groups work - the Switches group does not. Both the HDM and the HHC group should contain several devices. The HDM group contains 2, the HHC contains none. If I edit the groups and click "next" until I get to step 3, Membership: Edit, the "objects matching criteria" list is fully populated - it contains the devices that it should contain. However, after I click "Finish" and go to Inventory => Add / Import / Manage Devices there is no change in group membership - the HDM group contains 2 devices and the HHC group contains none.
I have a problem with User tracking. After a restart of the daemon manager or a reboot of the server the end host table is empty. All end hosts then have to be discovered again. is there any possibility to backup and restore the UT-Database?
View 1 Replies View RelatedOur customer has the business needs to authenticate remote users against AD with empty password. I've seen ACS5.1 release note where mentioned about resolved issue: #CSCte72751 #ACS 5.1 drops authentication with empty password.
I tried to authenticate dial-in users through Tacacs and Radius against AD with empty password but without success. ACS points to wrong AD password. Is it possible to authneticate remote users with empty password?
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
If I have understand correctly, the IP address - mac address matching was made with the arp table of a cisco acces switch if it will made the L3.
My access switch wasn't used for L3 routing, only L2
It's possible to set user track to use the arp table of a firewall or a router for made this matching ?
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
We bought a RV220W in order to get a VPN in our Small Business. The RV220W will only be used to let clients connect to it and not a tunnel between another VPN box.We could use QuickVPN, but it won't be working in our case, because in order to use QuickVPN, the router wants to change its IP 10.x.y.1. Because we have multiple servers/services that are using a static IP, it would be quite painful to change the subnet. Therefore, we would like to stay on the same subnet and change it in worst case scenario only. This is why QuickVPN is not an option here.We could use SSL VPN, but most of our clients who will connect to the VPN are using Windows 7 x64. I have tried the Windows 7 x64 fix told in the latest firmware release notes, but I can't get it to work on my computer, which is a Win7 x64. It might still be broken. Many of them are not very tech-savyy, so I can't tell them to use a virtual machine to connect.We want a secure connection, therefore IPSec is better than PPTP. I've been trying to setup IPSec for the past hours but I can't get it working. At first, I wanted to use an SSL certificate, but having no luck with this, I switched to a Pre-shared Key (PSK) in order to get things simpler. Eventually I would like to use an SSL certificate, however I would like to get PSK working first to confirm that the IPSec connection is working.
I have attached with this post, screenshots of the IKE and VPN Policies. I have used the VPN Wizard in order to complete these fields. The local identifier is the WAN DynDNS FQDN. However, as for the remote FQDN, there should be none really, because clients are connecting to it, so the RV220W won't know in advance who's connecting and from where. I have read that when using the Responder type, the remote settings should not matter. Also, the PSK is 25 caracters long.After setting the RV220W up, I have set up a L2TP/IPSec VPN connection on my Windows 7. I have set up the connection to connect to the DynDNS address and set up the PSK in the Advanced settings. After I typed my IPSec username and password to connect (which was created in the IPSec users section), Windows tries to connect and times out :
Error 789 : The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer.
At the same time on the RV220W, this error shows up in the logs :
2012-08-26 23:45:24: [rv220w][IKE] ERROR: Could not find configuration for 24.54.xx.xx[500]
I can't figure out what I am doing wrong. I've read the Administration manual quite a few times and it seems that I have followed everything by the book.I have tried to enable/disable my Windows firewall, but did not get any luck. The RV220W is located at a remote office, to make sure that I can connect from the outside, before you think that I'm trying to connect to the outside, from the inside I have changed few settings in the IKE policy to try to make it work. Settings such as the Exchange Mode, because I've read that the Aggressive mode had issues. At this moment, the settings are back to default, once the wizard has been run. I'm thinking about setting a PPTP to confirm that this works, then move up to IPSec PSK, then to IPSec SSL Certificate.
I installed the RV220W Router in my office about 2 weeks ago and everything works perfectly for 3-4 days but then my connection drops out and the router must be restarted to restore connectivity. When I say the connection drops basically the internet connection drops out and my network connections drop shortly thereafter. Usually the wireless connections lose connectivity followed within a few minutes by the wired connections.
Is there something in my firewall settings that could cause this issue? I have checked with my ISP to verify there are no problems on their end.
I'm on firmware 1.0.0.26 and I'm seeing frequent drops in the WAN connection. Most network clients don't notice the drop because it reconnects, but the X11 windows server running over a VPN drops the session and I have to re-establish it. Also, at the same time I experience a 15-20 second silence gap on my VoIP phone connected to vonage (not over VPN). Never happened on my Linksys router, but it happens many times a day on the rv220w. When the drop happens I get the errors listed below in the router log:
Fri Apr 15 09:53:21 2011(EDT) [rv220w][System][PLATFORM] platformHandleDBUpdate:dot11STA op=18 row=1Fri Apr 15 09:53:21 2011(EDT) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 1 failed. status=-1Fri Apr 15 09:53:21 2011(EDT) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=1Fri Apr 15 09:53:23 2011(EDT) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OKFri Apr 15 09:53:23 2011(EDT) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OKFri Apr 15 09:53:34 2011(EDT) [rv220w][System][PLATFORM] platformHandleDBUpdate:dot11STA op=9 row=1Fri Apr 15 09:53:35 2011(EDT) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 9 dot11STA 1 failed. status=-1Fri Apr 15 09:53:35 2011(EDT) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=1
how can i configure the SSL VPN users connexion to connecte from my remote PC (Windosws 7 32 & Internet Explorer
View 1 Replies View RelatedI've got trouble using PPTP connections with the RV220W small business router.When trying to connect to the router of a branch office with the Windows PPTP client (i.e. on Windows 7) from outside the companies network first everything seems to be in working order (user name and password are checked, the device is registered in the remote subnet) but then a window pops up saying there has been an error connecting.
Here is some information on my setup:RV220W with firmware 1.0.3.5It connects to the Internet using PPPoE dialindyndns account configured and workingAnother router working in "Act as a DSL modem" mode is used as a modem (AVM FRITZ!Box 7170)The RV220W is maintaining a IPSec tunnel to a main office, which is working finethere are 2 local VLANs (one with access to VPN tunnel, one without), each with a own subnet (192.168.201.0/24 and 192.168.202.0/24)PPTP users are on a seperate subnet (192.168.203.101 - 192.168.203.111) My first guess was, that the intermediate router acting as the modem could be a problem, but i verified all settings on that router and it should not filter anything. After all port forwardings, the IPSec tunnel and so on are working.
I am not able to establish a PTPP connection with my iPhone over WAN. When I am in my local Wireless LAN it works nice using the external FQDN of the RV220W. But when I test the VPN access over 3G (meaning I am coming in over the WAN port) I get and error message that the connection to the PPP server could not be established.
Some more Info
- Running latest firmware
- Port 1723 is open to the Internet
- ISP doesn't filter anything
- No Firewall settings blocking anything at the moment
- Nothing in the logs indicating what the problem is
So what needs to be done here to get it running over the WAN port and not only over the LAN ports?
My RV220W is sitting behind a Dynalink RTA1046VW ADSL Modem.
Can't get the RV220W to detect an internet connection through the WAN port. Have got the PPPoE profile set up etc. Have tried the Dynalink in bridging mode, but to no success. Tried the setup wizard.
Firmware is current: v1.0.2.4. The connection is picked up ok through the ethernet ports.
Lately (after upgrading to 1.0.2.1 and 1.0.2.4) I have been seeing these particular errors in my syslog server:
10.0.0.1 01/02/11 17:54:47 08/24/11 12:54:58 kernel Warning rv220w "KERNEL [Kernel] ERROR:endChantRecv: protocol PNAC returned !OK"
10.0.0.1 01/02/11 17:54:47 08/24/11 12:54:58 kernel Warning rv220w "KERNEL [Kernel]
[Code].....
I'm wondering if it's possible to setup SSL VPN connection via OPEN VPN client?I'm a Mac OS 1.7 user with Tunnelblick.
I tried to use "built-in" SSL VPN Tunnel client but unfortunately it's not working - during installation Java exception appears saying that either I don't have admin privileges or there is not enough space.. Of course I'm admin and there is plenty of space...
I'd like to enable client to router VPN connections. I have a question how to make any sucessful VPN connection to RV220W. From all the tests I made only SSL VPN on Windows XP x86 client machine was working.
For IPSec VPN I always receive this message: [rv220w][IKE] ERROR: Could not find configuration for XXX.XXX.XXX.XXX[500]. I tried with windows and shrewsoft vpn client.
Can't make SSL VPN to work in Windows 7 x64 client because the drivers are not digitally signed. It only works in Windows XP x86 but this is not acceptable. I need universal solution for win clients.
I also need working solution for Android Phone? Router firmware 1.0.3.5. I also tried this step by step guide. No go.
I am using LMS 4.2 I have enabled user tracking and I am getting ip address, MAC address ,hostname in user tracking table . But username entry in user tracking is not getting populated . Even I have enabled get user name from the hosts in NTS and ND host domains in user tracking acquisition settings .Is there anything else that I need to configure in LMS in order to get the usernames in user tracking table?
View 3 Replies View Relatedi'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.
View 1 Replies View Relatedi have try to make a IPSec VPN Connection from my iPhone to my RV220W.
On the iPhone i get the message "The VPN Server was not found".
It is possible to make a IPSec Connection or only a PPTP ?
We are running LMS Prime 4.2.3 on a Softappliance. We have a Cisco Switch behind a Non Cisco Layer-3 Device. In the end host tabe we see only the MAC-Addresses of the host connected to this switch. No IP-Address. The corresponding IP-Addresses are in the ARP-Table of this non Cisco Layer-3 Device. The arp table can also be read by snmp. Is it possible to get the ip address in the UT End Host Table in such an environment?
View 1 Replies View RelatedWe have RV220W at corporate office...intent is to have (5) groups of (3) users each connecting via VPN. Had assumed would be using QuickVPN and have set up users, etc and connections at current locations are quick, smooth, reliable. I have set up (2) locations (6 users so far). However, after 4th connection (no matter where or in what order) client hangs at "Verifying Network" and doesn't complete connection. So, I have unique usernames, etc but each of the (3) at a location are hitting the router with the same IP. Is this the problem? I'm sure the RV220W can handle 15 simultaneous connections, but can the router deal with (3) connections from the same external IP?
View 3 Replies View RelatedIn datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies View RelatedI am currently using 2 routers. One is a 2wire router with stock firmware it is connecting to the internet and can't be altered all too much, it also has a PC connected to it. The other is a WRT54GL with Tomato on it with pretty much EVERY other PC and device connected to it, it is also connected to the 2wire and DMZ'd through it.What I want to do is somehow allow everything on the Tomato router to have access to the 2wire router's PC. (For media access or printers or whatever on Windows 7)
View 13 Replies View RelatedI would like to find out what the status is of the Cisco 7204 VXR and 7206 VXR routers?I understand they are EOLife and EOSale.Are they also EOSupport? we planning to upgrade 3 of them in our environment and management requires feedback around this.We thinking of going the ASR1000 route..
View 15 Replies View RelatedWhere is the disconect button on the VPN Status page gone in FW:1.01.26 (003) ? It used to be there as you can see in the below screen shots...
FW: 1.01.19(004)
FW: 1.01.26 (003)
ASA5545 : Software Version 8.6(1)2Connection table (cfwConnectionStatValue) gradually increases and never goes down. Upon 750000 connections, user activity is hampered and the box claims that it can not support more connections.
View 4 Replies View Related