Routers And Static Routing Table
May 9, 2012
I am currently using 2 routers. One is a 2wire router with stock firmware it is connecting to the internet and can't be altered all too much, it also has a PC connected to it. The other is a WRT54GL with Tomato on it with pretty much EVERY other PC and device connected to it, it is also connected to the 2wire and DMZ'd through it.What I want to do is somehow allow everything on the Tomato router to have access to the 2wire router's PC. (For media access or printers or whatever on Windows 7)
View 13 Replies
ADVERTISEMENT
Jan 31, 2012
I tried the "Advanced Routing" Feature over the RV-042 V3 Dual WAN VPN Router , And the New IP Subnet i added ( 10.0.7.0 ) in the Static Routing Table does NOT Appear in the Routing Table of the Router. Please review the attached Print Screen for both the Static Routing Entry Configuration & the Routing Table of the RV-042 Router.
View 0 Replies
View Related
Jan 3, 2013
I've been playing around with the Cisco RV180s for a while now and have come across a problem with the subnet calculation in the static routes and routing table. Essentially, if I configure up a static route for a /16 it's entered in the routing table as a /13. If I add a /24 it's entered in the routing table as a /16. I haven't tested every subnet size and combinations but this looks like a fairly fundamental maths bug.
As a side note, I notice that the 1.0.1.9 release notes state the removal of SSH Server, however, I can not find any reference to it's existance prior to 1.0.1.9, did/does it exist in 1.0.0.30 and if so where? .
Screenshots are below and an extract from the configuration file for reference.
From the config file:
route = {}
route[1] = {}
route[1]["active"] = "1"
route[1]["dstIpAddr"] = "8.8.0.0"
route[1]["gwIpAddr"] = "192.168.1.250(code)
View 1 Replies
View Related
Dec 5, 2012
I started using RIPv2 on Packet Tracer. I got two subnets to connect with two routers. After I completed that, I decided to add a third router. How to setup the Routing Table for atleast R3 ?
View 5 Replies
View Related
Jan 16, 2013
In datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
View 3 Replies
View Related
Sep 21, 2011
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
View 3 Replies
View Related
Jun 22, 2011
I have enabled DHCP but want to set static table IP's for my security camera DVR and one computer, the others can remain dynamic. I know in other routers I can attach a LAN IP to a mac address to keep it static but I can't see where I can do that with this router.
View 4 Replies
View Related
Sep 2, 2012
i'm trying to create a VPN IPSEC link between 2 offices. The VPN link is created, and i can communicate but only one way. Clients in Office B seems to have routing problem.
Details :
Office A :
- SRP527W router.
- Client Network : 192.168.0.0 / 24
[Code].....
View 5 Replies
View Related
Mar 12, 2013
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
View 3 Replies
View Related
Oct 8, 2011
I have 8 RVs4000's to built a test system with. On each side of the network is 2 servers, both with 2 NIC's. Both are on different /24 networks.
The idea is to simulate a WAN link, with the RVS4000's G1 & G2 running in "Gateway" mode to simulate the WAN. All other RVS4000's will be in Router mode ('R1,R2...etc..') All networks in /24 range. As I understand it, the RVS4000 CANNOT take 2 diverse networks on the LAN side: - ie 192.168.168.1 & 10.1.1.1 on the LAN side. The NIC's on the server only need to communicate to the similar type of addresses on the other side - 192.168.168.1 on server 1 to 192.168.170.2 on server 2, but NOT 192.168.168.1 to 10.1.2.1 on server 2. The G1 & G2 link is so that all communications are routed between this link - as a testing point.
So, my questions are this:
1) Will this work? Is there any easier way of doing this? (Bear in mind this is the only equipment i have to do this).
2) Is the static routing I have thought of work? (see below)
R1
0.0.0.0 0.0.0.0 10.1.1.10
R2
5.5.5.0 255.255.255.0 10.1.1.100
4.4.4.0 255.255.255.0 1.1.1.200
[code]....
I know using the RVS4000's inbuilt RIP may be easier, but I've never configured RIP routing. As this is a test environment, using static routing would be enough to get it going. No security lock down is required, all I'm trying to enable is for the servers to communicate with each other (NIC1 on both servers e.g 10.1.1.1 on server 1 to 10.1.2.1 on NIC 1server 2, and NI 2 on server 1 192.168.168.1 to NI 2 on server 2 192.168.170.1) The 10.1.x.x networks DO not need to talk to the 192.168.x.x networks. THe G1 & G2 link is just for testing - but all communications must pass through here and be routed to their relevant networks on the other side.
View 4 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Feb 15, 2012
I was wondering if anyone has seen their VPN User Connection Status Table empty even though you know for sure clients are connected? I connect with my iPhone to the PPTP VPN successfully and it works fine but there's no entry for the connection on the VPN User Connection Status Table. Is that normal? Does the router only collect data about Windows clients?
View 3 Replies
View Related
Feb 13, 2013
I have recently purchases a Cisco srp547w for my organisation. It is working fine with one SSID enabled. I have configured everything with no problems using the Web interface. However, whenever I click the Edit button, in the Security column, in the Wireless Table under Basic Wireless Settings I get a pop up message which says :"Some values have been changed. The router must restart the wireless module to take effect.Please wait several seconds" I have tried this using 3 different browsers and get the same behaviour in each browser.
View 1 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Oct 2, 2012
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies
View Related
Nov 14, 2012
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1
Router B in site 2
Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
View 13 Replies
View Related
May 22, 2013
I am attempting to filter a specific host(s) from my OSPF routiing table on a ASA 5550 (ABR) using LSA prefix lists. However, when I look at the other routers in that area, I notice that ALL LSA type-3's are being removed (10 hosts are now missing from the routing table). I have verified the filter is working on the ABR, but I can't figure why ALL hosts/routes that were coming into the area are now being filtered instead of the specific one that I want to filter out.
Here is the config on the ABR:
prefix-list pdm_pl_000 seq 10 permit 206.253.180.137/32
!
!
router ospf 1
network 10.0.0.0 255.255.255.0 area 0
network 10.150.10.0 255.255.255.0 area 10
network 10.150.252.0 255.255.255.224 area 10
[code]....
The 206.253.180.137 host is actually coming from Area '3'. Am I doing something that is removing all type-3 LSA's?
View 3 Replies
View Related
May 28, 2011
I'm learning about iptables, but I don't fully understand the chains of NAT table (prerouting, postrouting and output).I'm specially in doubt about prerouting and postrouting. As far as I know, DNAT can be made with prerouting and SNAT can be made with postrouting, so I think prerouting is for input and postrouting is for output, but the material I'm reading (and another sources) are not clear.
View 4 Replies
View Related
Dec 8, 2012
I have this routing table which I need to fill in for the network shown in the image attached. guide me to some good resources to understand
View 1 Replies
View Related
Feb 4, 2013
We have a BGP / OSPF configuration as shown in the topology picture. When the connection towards Internet is taken down, we expect the traffic to be forwarded toward WAN 2 (preferred) or WAN 1. The problem is that the BGP learned routes disappears when the Internet connection is taken down. The IP routing table on R2 only shows internal networks and the networks between R2 and WAN 1 and 2. No routes to internet is shown. We run "show ip bgp neighbors <ip-to-wan-1-router> received-routes" it contain internet routes. And when we run "show ip bgp neighbors <ip-to-wan-1-router> routes" it contains no routes at all.
View 2 Replies
View Related
Feb 22, 2011
Which data structure used to preparation of a routing table.
View 6 Replies
View Related
Apr 2, 2013
viewtopic.php?f=33&t=24000
How can you remove these "L" routes in routing table?
View 6 Replies
View Related
Jul 2, 2012
What are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
View 1 Replies
View Related
May 26, 2013
What is the size of the routing table in the 800 series?
View 1 Replies
View Related
Dec 10, 2012
I have a problem on a router of mine, a Quidway R 1760.The problem occurs as follows. On Friday I rebooted the device and the ARP table looked right, in other words there were only a hand fully of lines that looked like this.
[code]...
I have two requests/questions.how can I prevent it.to a software manual for a Quidway R 1760 or simlar? I need to access the routers OS but have no password for it and cannot find any commands on the internet.
View 3 Replies
View Related
Jan 23, 2011
I need to remove (or change) the default entry in the routing table for Windows XP, which routes packets with a destination equal to the adapter's address to localhost. The reason for this is I want the PC to be able to send packets to a device (with IP address A) connected to one adapter on the PC with IP address B, even though a second adapter on the PC has IP address A.
View 1 Replies
View Related
Nov 27, 2012
Is there a Table which the list the route table entries on Cisco ISR Router especially ISR 1921 Router.
View 3 Replies
View Related
Feb 6, 2013
On the 6509, with normal 67xx cards installed, where is all the mac table held, is it held on the card itself or on the supervisor? And if I use dcef cards, I gather the MSFC copies the mac table to the DFC ?
View 1 Replies
View Related
Jan 11, 2012
Cisco 1812, Version 12.3(8)YI1..What does "none" mean ?Most of mac adressess in cam has specified interface, but several has none.
View 12 Replies
View Related
Jul 7, 2012
I know its probably got something to do with EIGRP no auto-summary, I was wondering if I could get some input as to why a route would change from being variably subnetted, which is usually the case until no auto-summary is deployed. Or am I totally lost? I attached a screen shot for a closer observation.
View 1 Replies
View Related
Feb 19, 2012
I am in need to have the arp table cleared every 5 seconds or so on a 2800 router. I was wondering how I might be able to accomplish this.
View 4 Replies
View Related
Jul 23, 2012
My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies
View Related
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
