i'm trying to create a VPN IPSEC link between 2 offices. The VPN link is created, and i can communicate but only one way. Clients in Office B seems to have routing problem.
Details :
Office A :
- SRP527W router.
- Client Network : 192.168.0.0 / 24
[Code].....
I'd like to create a site-to-site vpn between an SRP527 and an other vpn gateway. The problem is i don't see how to route all traffic from the local network (network defined by the lan ip interface of the SRP527) to the other vpn gateway? It seems to be only possible to define the destination network (accessible via the vpn) with ip/mask (but only for "small" network: for exemple i tried with 10.2.0.0 mask 255.255.0.0 and it's ok but i tried with 10.0.0.0 mask 255.0.0.0 -> it's not working. I obtain the message "invalid ip")
View 1 Replies View RelatedWe recently purchased an SRP527W router because of its capability to configure site-site VPN tunnels. The configuration of IKE and IPSEC is working and the tunnel comes up but the problem is that the router is passing our internal IP addresses through the tunnel. The remote end we are connecting to requires us to hide all traffic behind one IP address which would ideally be our external static IP address from our ISP.
View 1 Replies View RelatedI have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I have problem with setting up the port forwarding on the VPN between two cisco 527w.
Scenario where a Site to Site VPN tunnel has been established between Site A and Site B; a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. As the picture above:
- From site A, I am able to ping printer and access to printer locally and via 120.146.x.x with port forwarding setup on site A to the printer.
- From site B, I am able to ping site A gateway but not able to access to the printer via 120.146.x.x. The printer can be access via 129.203.x.x if the port forwarding is setup on site B to the printer.
Does Cisco SRP 527w support port forwarding over site to site VPN from site A to printer on site B?
I am trying to configure a SRP527W for a remote site.It needs to connect back to our Central Office, (via an ASA) which has several VLANs configured. I have entered the configuration for an IKE policy, and one for an IPSec policy (I can only enter one ip/subnet per IPSec policy)When I try to create a 2nd IPSec policy, if I point to the existing IKE policy, I get an error stating "IKE policy has been used by other IPSec policy".If I try to create a new IKE policy, using a different name, but with the same parameters, it shows an error stating the policy is a replica of an existing policy.If I create a new IKE policy, but use a different pre-shared key, then it is accepted by the 2nd IPSec policy, but that would mean I would have to create 2 seperate tunnels on the ASA, each using a different pre-shared key. I have never needed to do this for any of the other routers we have connected.
View 1 Replies View RelatedWe use the RV082 at some our sites. One particular site will not connect to the DNS server but all others will. I've checked every setting I can think of with no joy.
View 2 Replies View RelatedAs you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies View RelatedCan I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?
View 3 Replies View RelatedIs it possible to have a site-to-site IPSEC tunnel between 2 identical RV110W routers?I basically want one of them to initiate a secure tunnel with the second so that computers from one router subnet see the computers from the other router subnet.
View 3 Replies View Relatedthe RV110W IPSEC site-to-site tunnel, are there necessary 2 x public IPs for it to work, or only 1 public IP is enough? [code]If it works with 1 public ip, the "CLIENT" RV110W configuration should be straightforward (in Advanced VPN SetupRemote Endpoint i fill in the dyndns address?), but how do i setup "HOST" RV110W?
View 2 Replies View RelatedWe have successfully establish a site-to-site vpn, but we have some difficulties when PPTP users try to access the remote network linked by this tunnel. LAN users can access the remote network without problem, but users who are connected remotly to the lan (PPTP) can't access computer on the remote network. Is there a way to allow PPTP user to access the remote network ? Adding a route ?
View 1 Replies View RelatedI'm installing a new SRP547W for a client and am having trouble setting up a site-to-site vpn. They are using the WAN1 ADSL interface for their internet connection. When I add a sub interface to it I am unable to see the 'Connection Type' drop down like I can see on a WAN2 ethernet sub interface. I have followed the instructions on page 29 provided here: how I can get a a site to site vpn set up on this router using either PPTP or L2TP over the ADSL interface.
View 1 Replies View RelatedIs there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
I have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
I am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.
View 1 Replies View RelatedI am having a heck of a time configuring 2 RV180W's to establish an IPSEC VPN tunnel. I have some experience at this with other Cisco products (RV042/082) but I can't get these beasties to cooperate.One RV180W is at a client's office and there are to be 1x RV180W and 1x RV120W located at 2 employee's residences.The office has a Static IP and the homes have dymamic IP.I figured I would config the units in the homes to be initators and connect to the office where the static IP is. This is failing for me so far. Any example (screenshot?) of a config where this is working? The firmware on the RV180W's I am trying to configure first are current.I even tried testing from my office (where I have multiple static IPs available) from RV180W here to RV180W at client's office (static at both ends) and I can't get a tunnel to come up. Obviously I am missing the boat at some point in the setup.
View 1 Replies View RelatedI have a site to site VPN tunnel configured between a rv220w and rv180. Everything works fine going from site to site on LAN connections. I'm now trying to tie in the remote site wireless (rv220w side) by pointing radius to my ACS server which is on the other side of the site-to-site tunnel but it seems as though it doesnt route across the site to site tunnel. If i put a radius server on the local lan on the remote site that authentication works fine. I have confirmed there are no ACL problems. the RV220W capable of using a radius server across the vpn tunnel?
View 1 Replies View RelatedI have an issue with 2 site to site VPN tunnels from a RV042G router. The issue is for both VPN tunnels is that in the logs, it is showing that when the RV042G router is trying to establish the tunnel, it is getting a response from the remote gateway internal address and not the Public address of the remote gateways. On the remote gateways I have other site to site VPN's terminating fine and the tunnels are passing traffic. I only have an issue with the RV042. On the VPN Tunnel page it shows for both tunnels waiting for connection. This is an output from the log of the RV042G
Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: Peer ID is ID_IPV4_ADDR: '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: we require peer to have ID '203.43.XX.XXX', but peer declares '126.0.21.52' Dec 17 15:19:48 2012VPN Log(g2gips0) #2174: sending encrypted notification INVALID_ID_INFORMATION to 203.43.XX.XXX:500 Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: [Tunnel Negotiation Info] >>> Initiator Receive Main Mode 6th packet Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: Peer ID is ID_IPV4_ADDR: '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: we require peer to have ID '203.47.XXX.XX', but peer declares '10.1.202.65' Dec 17 15:39:50 2012VPN Log(g2gips1) #2192: sending encrypted notification INVALID_ID_INFORMATION to 203.47.XXX.XX:500
VPN tunnel terminating on 203.43.XX.XXX is a Checkpoint firewall running R70 software version?VPN tunnel terminating on 203.47.XXX.XX is a Cisco ASA 5510 running ASA 8.2.4 software?As stated above, I have other VPN tunnels working fine. This RV042 is a replacement router as the original router suffered a power surge.
I want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
I have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
I have several sa520 appliances, and one of them came with the 2.1.72 firmware and it works perfect... with all others I upgrade to 2.1.71 (because I was not able to find 2.1.72) that is the latest posted in the CISCO download area.So, is there any way to get 2.1.72 ?With the 2.1.71 the VPN Site 2 Site works fine some time, but later it disconnect and it does not connect until I disable /enable the VPN.
View 2 Replies View RelatedI am trying to configure my network so that VPN traffic is only routed to a single physical port on the RV180 or to a certain subset of devices on a network.
I have a site-to-site vpn setup in a home office and am connecting to the corporate network. The user has a couple of devices running on the home network that need access to the corporate network.
We are hoping to leave his PC accessible to his home network as well as the corporate network, but restrict other devices from accessing the vpn.
I beleive I could do it by playing with the subnet but I can't get my head around it.
I'm setting up a site-to-site VPN between two offices, Site A uses a Cisco RV110W VPN Router with a static WAN IP and local IP 192.168.1.0/24 while Site B I have set up with a Belkin N300 VPN router which also has a Static WAN IP and the local IP is set to 192.168.2.0/24
I'm able to ping from Site B (192.168.2.xxx) to Site A, however I can't communicate from Site A back to Site B.how I could go about troubleshooting this? I've been scouring the internet for 3 days trying to get to the bottom of this with no luck.
I am building a site to site VPN from our headquarters to a customer. I am using an ASA 5520. The customer is using Cisco 3945 routers. The customer has two VPN termination points. The customer requests that we make one of their termination points the primary VPN connection and make the other termination point the backup in the event that the primary VPN fails. How do I configure this on the ASA? Does the below configuration fulfill this goal?
View 3 Replies View RelatedI have no problem configuring both devices to successfully connect when the juniper firewall isn't in the picture. But due to policy; the RV042 at our main site must sit behind the firewall.
I've got the port forwarding setup but I'm not able to connect. I know I"m missing some configuration on the RV042 but I can't think of it! I've attached a GIF to give an example of both setups.
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedSo I just got a couple of Cisco RV180 routers that I am trying to setup a VPN link between the two. Both have their own static IP addresses on the WAN side, and so I used the Basic VPN wizard to define the public addresses for each other, use a pre-shared key, and set the local IP address ranges in the routers in the following layout: Router ALocal: 172.16.0.0/24Router BLocal: 172.16.1.0/24When I try to ping from one end to to a computer on the other I lose all the packets. When I looked at the transmission information, I found that Router A is transmitting but not receiving and that Router B is receiving but not transmitting.
View 0 Replies View RelatedAny one with any insite into getting this working. I have an rv180 configured for site to site vpn and dynamic routing. Should be a simple task but the vpn connects for a second than drops.
View 1 Replies View RelatedWe having 2 nos 1941 routers we need configure site to site vpn on this routers send the configurations . 1st side having server and 2nd site we having 10 users. 2 side users wants to access trough vpn in that server .any IOS required are defualt IOS is enof on 1941 k9 Router.
View 3 Replies View RelatedI have been asked to setup a site to site VPN link between two 877-w routers.Not yet had a chance to look at the actual pieces of hardware as they are overseas.
View 3 Replies View RelatedI have got two CISCO RV042 .I need to configure a site to site VPN .
View 1 Replies View RelatedI want a site to site vpn ipsec tunnel there wants to use two Cisco 880 routers that are connected to a modem / router is this possible?
View 12 Replies View Related