We are using an ASA with 8.4 in transparent mode. Connection fails when a host on inside tries to connect to a server on outside. This server uses mac-address 0100.5E00.0000 to load balance but replies with real mac-address.Firewall logs "Deny TCP".ARP inspection is disabled.
View 2 RepliesI have a 5520 in production at a customer's site between an outside 802.11 network and an inside server. The server can get to outside hosts OK, and the traffic is being NATed properly, and sockets initiated by the server on the inside can pass data both ways, but I need to allow outside hosts the ability to send 'announcement' UDP packets to the inside server. I thought this might be an outside-NAT-required issue to get the traffic routed, but I need the inside server to see the actual outside host source IP in the UDP packet, so I basically set the outside host up similar to the inside host, just without the NAT table on the firewall -- it's subnet is outside the destination (inside server) subnet, and its gateway is the outside interface of the ASA, the same way the inside server is able to get to hosts outside. The firewall should just route the packet with a destination of the inside subnet once it sees that it hits a 'permit' ACL.
I have the appropriate ACL's set up, and when I do 'show access-list' I see policy hits for the 'permit' statements where the outside host is generating the announcement and it's hitting the ACL. I even duplicated the ACL into list 101 and 102, and applied 101 for inbound traffic on the outside int, and applied 102 for outbound traffic on the inside int, and I'm seeing policy hits on both permit statements outside and inside, so it looks like the traffic is being passed on to the inside interface and permitted, but the server isn't seeing the packets.
I can ping the outside interface from the outside, but cannot ping the inside interface or any inside hosts from the outside, even though I have 'permit icmp any any' enabled on the ACL on both ints. When I remove the firewall and put the outside clients on the same subnet, the server sees the packets just fine.
I set up the same scenario in my lab with an ASA 5505, with the same results. Below is the running config from the 5505 in the lab. The production firewall is running a slightly older version of ASA, so I made the configuration as basic as possible on the 5505 to match the config in the field:
: Saved
:
ASA Version 8.3(1)
!
hostname ciscoasa
enable password Guh9Xxhb9mcC8lV1 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan2
description Outside WAN Interface
nameif outside
security-level 0
ip address 192.168.10.1 255.255.255.0
!
interface Vlan3
description Inside LAN Interface
nameif inside(code)
Minecraft 1.3 LAN server function fails because host IP bad. The host (a laptop) connects to the LAN with a proper 10.0.1.X type address, but this particular laptop uses a 169.* address when it establishes/reports the game (instead of it's 10.0.1.X) and no other computer can connect to it. Other computers DO establish/report the 10.0.1.X address they receive from the wireless router, and they can host just fine- but I really need to get the one laptop to serve as host since it has more horsepower.
View 10 Replies View RelatedI hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 Replies View RelatedI have a ASA 5505 Sec Plus. I would like to allow outside hosts to our mail server and also our FTP server. So i would like to allow only SMTP, HTTP (for Outlook Web Access) and FTP.
View 10 Replies View RelatedI just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
Wondering if on the ASA (8.4) its possible to do something like what DNS rewrite does, but with IP requests. Scenario. Mobile phone accesses a web app inside our network fine over cellular. Once it comes inside on to wifi it still has the public IP address cached so the ASA doesn't allow its request to loop around and the app appears broken. We're considering lowering the TTL on the DNS host entry but I think we are battling phones/mobile OS's that don't have a strict adherence to name resolution standards. A lot just seem to refresh their caches every 10-15 minutes.
View 4 Replies View RelatedI have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
interface GigabitEthernet0/0nameif outsidesecurity-level 0ip address 198.24.210.230 255.255.255.248!interface GigabitEthernet0/1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0
[Code].....
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedInstead of using a IP address I would like to use a host address that points to a NTP pool.An example would be:ntp server 0.north-america.pool.ntp.org Can this be done on the ASA series?
View 1 Replies View RelatedTrying to allow inbound access from any host outside to my LAN server on port 995. [code]
View 1 Replies View RelatedWhat I have is 3 interfaces on my PIX.- Outside: 216.116.87.0/24 (security level 0)
- 469: 172.16.6.0 /24 (security level 10)
- 571: 192.168.255.0 /24 (security level 1)
My users on 571 need to access a web server on the 469 interface. However, the requirements are that the 571 users can only access the Website using the public FQDN which there is a static NAT from outside to 469. [code] Here is also the Packet-Tracer and it shows what I expect that the traffic is source from 571 and exits 469. However, the users are not able to access the website.[code]
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
I have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View RelatedConfiguring an asa 5505 with 8.42 software.I need to access an https server on the inside via the outside interface. have moved the http server enable to port 10443.Tried to make a "network object nat rule"
object network Vejrstation nat (any,outside) static interface service tcp https https object network Vejrstationnat (any,outside) static interface service tcp https https.
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
configure my Cisco ASA5510 (asa version 8.3.1) so that one of the host (e.g.192.168.8.20) behind management interface can ping to the other host (e.g. 192.168.2.246) behind OUTSIDEinterface. I tried modifying the ACLs, NATs and ICMP statement, but still failed[CODE]
View 19 Replies View RelatedI'm having trouble setting up the correct rules on an ASA 5505 I'm using in my home office. I have a couple of IP Cams I need to access remotely.
I've tried setting up simple NAT(PAT) and/or Access Rules, but it hasn't worked. I have a single dynamic IP for the Outside interface. Call it 77.76.88.10 and I am using PAT. The CAM is setup to connect on port 80, but could be configured if necessary. I've tried setting up NAT Rules using ASDM as follows:
Match Criteria: Original Packet
Source Intf = outside
Dest Intf = inside
[Code]....
I'm afraid to use CLI only because I am not confident I'll know how to remove changes if I make a mistake.
We've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies View RelatedMy internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I tried to remotely access my disk connected to the USB port of the EA4500 and it failed until I disabled the IPv4/IPv6 SPI Firewall options. Surely, the firewall should not block the router's own FTP server!
View 8 Replies View RelatedI am having problems accessing our internal network via VPN. We have an ASA at the perimeter that connects to a 3745 router and all of our networks come of that router. I can establish a VPN connection to the ASA but I can’t ping any of our internal host.
The internal network I need to access is 172.18.0.0. When I connect to the ASA I get a dhcp address from a pool created in the ASA, the pool is 172.200.1.x. I can’t ping from the ASA to the connected vpn host and I can’t ping from the host to the ASA ip address or to 3745 connected to it.
ASA config:
group-policy NAMEOFPOLICY internal
group-policy NAMEOFPOLICY attributes
dns-server value 172.18.2.2 172.18.2.23
[Code]....
route inside 172.18.0.0 255.255.0.0 172.18.255.1 1 Route on the 3745 back to the ASA ip route 0.0.0.0 0.0.0.0 172.18.255.2 I can’t see anything on the internal network, I can’t even ping the dns servers and so on.
I am trying to telnet to my asa 5510 from the core swith,however i received the below msg,how enable it?
172.30.1.100 is the inside interface of the asa
CITYCORE#telnet 172.30.1.100Trying 172.30.1.100 ... % Connection refused by remote host
CITYCORE#
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
so i have a ASA 5510. The ASA is Connect with the Internet through PPOE DSL MODEM
The outside Interface get an IP. The Inside Interface get through DHCP from the ASA the Internet DNS SERVER (T-Online) But the HOST do not connect to the Internet because the DNS Server is timed out
Code...
We have an ASA5510 with the IPS ASA-SSM-10 module installed. All is working well except event notification. When sending a test email from the SSM IPS, we get the error "could not connect to SMTP host". The Exchange SMTP host does allow traffic from the IPS and ASA. I can ping to the SMTP host by IP and name. What am I missing here?
View 3 Replies View RelatedMy PC Info: Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5850 @ 2.16GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3069 Mb
Graphics Card: ATI Mobility Radeon HD 3450 , 256 Mb
Hard Drives: C: Total - 305242 MB, Free - 252510 MB;
Motherboard: Dell Inc., 0F700C, , .8QQVVG1.CN4864388L1948.
Antivirus: Norton Security Suite, Disabled
So I am having issues connecting to the internet. I can connect during safe mode but not on normal boot. I ran a diagnostic and it said that the IP Gateway failed. I read a previous post and did the command promp "ipconfig/all" and this is what it said:
Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersEbony>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ebony-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....
I have norton, and have recently run Malwarbytes, Microsoft Malicious Removal Tool, and Dell PC Tune Up
Version: Cisco ASA 5510 8.4(4)1
I've installed cisco asa 5510.
When I "show local-host all detail connection "
Normal situation:
105 myfailover:10.255.255.2/0 NP Identity Ifc:10.255.255.1/0,
idle 0s, uptime 1D14h, timeout 2m0s, bytes 18196822
But I got this output ( timeout - )
[URL]
I have a test ASA 5505 with the setting below:
How can I connect to the internet (Vlan 1 to VLan 11)
[code]....
I purchased two WUSB600N V2 wireless adapters recently and have had nothing but problems on an otherwise stable network where I have iPads, iPhones, Netbooks, media centres, wireless printers, Notebooks and other USB PC-based network devices working without problems.
The WUSB600Ns are connected to desktop PCs, running WIndows XP SP3. I have removed the Linksys Network Management software and use Microsoft's wireless network management software. I am running the latest drivers 1.4.10.0 for the cards. My WAP is a Belkin F5D-8236-4 running in WAP only mode. It is set to 40Mhz Channel 11 primary, Channel 7 secondary. Protected Mode is off, Broadcast SSID is on. I run WPA2-PSK AES for encryption. Note: I've tried all combinations of bandwidth and channel settings. I've run Netstumbler to find clear air channels - 11 seems best.
The issues are:
* seldomly connects at boot automatically without intervention.
* occasionally does not find WAP to connect to.
* sometimes will not connect to WAP - sits at "Acquiring Network Address".
* sometimes will not even get to Acquiring Network Address.
* Will often, once connected, after a while lose connection - the timeframe is inconsistent.
All of my other devices do not have these issues. I've been working on this issue for about a week trying to stabilise, even get a consistent failure pattern, but I'm about to send them both back.These are close to the most frustrating devices I've configured and I've got a lot of stuff on my network.
For some reason there are some sites that I cannot access websites from inside interface.One such example is lxer.com where I am receiving this message in the browser:The connection has timed out The server at www.lxer.com is taking too long to respond.This has "suddenly" happened, and so I am wondering what others have done when such things has happened. My outside has a dhcp-IP, and I have noticed that this address had changed, so I corrected this in my router settings.ASA version is 5505
These are my settings:
: Saved
:
ASA Version 8.4(2)
!
hostname ciscoasa
domain-name example.no
enable password 123412321 encrypted
passwd 1231231 encrypted
names
[code]....