I hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 RepliesMy internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
I have an ASA 5510 which i've configured for internet access.I can connect to the internet from the ASA box,I can ping public networks from the console of the ASA box,but cannot access public hosts from internal hosts connecting via the ASA box.Find my config below to know what i ahave omitted or committed.
[code]...
The router is 2821 and is setup to perform static NAT from one internal ip address mapping to one external ip address for each of our servers (inside the LAN): [code] Servers all have internal ip addresses and each of them represented to the outside world by their public ip address with above command on the router. Here is the problem.When I'm in a server (for example 192.168.0.210) and try to access other servers by their public ip addresses (i..e. *.*.*.211) the connection fails. However, When i try to access the same server by it's private IP address (i.e. 192.168.0.211) it works!
My issue is i don't want to modify windows host file for a manual mapping (for example mail.mydomian.com goes to 192.168.0.211 rather than *.*.*.211) because we host many domains and just doesn't make sense to do it one by one.So we must be able to access our servers by their public IP addresses in order for us our applications works correctly.
We are using an ASA with 8.4 in transparent mode. Connection fails when a host on inside tries to connect to a server on outside. This server uses mac-address 0100.5E00.0000 to load balance but replies with real mac-address.Firewall logs "Deny TCP".ARP inspection is disabled.
View 2 Replies View RelatedI'm trying to traverse from my inside private IP address (10.x.x.x) to my public IP address translation (172.16.x.x) in order to take advantage of the ACLs that are already applied on my outside interface. For example:
Host 10.0.0.1, translated to PAT pool
Server 10.0.0.5, translated to 172.16.0.1
Inside-out access-list permits ip any any
Outside-in access-list permits tcp any 172.16.0.1/32 eq 80
From my inside host, I can get go 10.0.0.5:80. I can get out to the internet. External hosts can successfully get to 172.16.0.1:80 (address scheme is theoretical). I can do everything except for connect to 172.16.0.1:80 (the translated public IP address) from my inside host address. I did not setup this firewall originally, but I can't see a blatant command that makes this not work. I don't see an ACL rule matched, so I'm assuming this is an issue with NAT or some sort of security policy. I'm running a Pix 535 /w 8.0.4. The response I got from Cisco was "create static (inside,inside) translations for every host", but that's over 300 hosts. I have a friend running the same software set and his works as expected without these static (inside, inside) NATs.
I need to connect from an inside host to a host located in the DMZ zone for DNS queries. The host in the DMZ zone has a static NAT to the outside. The point now is that I would like to connect from inside to the NATed outside address, means to the public Internet address.
Inside host: 10.0.0.1 -> PAT for 10.0.0.0/8 to 20.0.0.254 (Outside Interface)
DMZ host: 192.168.1.1 -> NAT to outside to 20.0.0.1
The traffic should be 10.0.0.1 udp>1024 to 20.0.0.1 udp=53. The source IP address on the outside interface now is 20.0.0.254 (according to the PAT), the destination IP address 20.0.0.1. The DNS reply from 20.0.0.1 should go back now to 20.0.0.254 and then to the inside host 10.0.0.1.
I know that on the PIX it was not possible, to have outgoing traffic on the outside interface which immediately enters again the same interface. Can I realize this scenario with the ASA 8.4(3) release now?
Got an ASA5525-X with 8.6 release. We have an inside interface (10.11.1.0/24) and a DMZ interface (10.254.1.0/24). On that DMZ interface theres an SMTP server; by using the Public server feature in ASDM we created a rule so we have mapped the 10.254.1.29 internal ip to an external ip 217.x.x.x Everything is fine; working ok, but for several reasons we need to access the public ip 217.x.x.x from an inside ip (10.11.1.10). I tried to do it by creating an exemption for the dynamic nat; if i don't do that i have a 'deny ip spoof from...' message rolling on my syslogs.Seems to do the trick.....but only for pings! i ping the public ip from the inside ip, and got the reply from the internal ip on the DMZ. But if i want to telnet port 25 from inside to public; its not working.
View 7 Replies View RelatedI'm stuck at asa 5505 nat, port forwarding configuration Here is what i need:
host1: 192.168.1.1 service tcp/100 >>>>> public ip 1.1.1.1 service tcp/100
host2: 192.168.1.2 service tcp/200 >>>>> public ip 1.1.1.1 service tcp/200
host3: 192.168.1.3 service tcp/300 >>>>> public ip 1.1.1.1 service tcp/300
So people from remote just need to use 1.1.1.1 public ip to access all the ports on three different inside server.I can do this on my old ASA 5505 with 8.0(4). Looks like there're lots of change from 8.0 to 8.4.
We have ASA 5550, I have a portal server in the dmz which is natted statically to a public ip address for port 443. The application works fine from outside world. The server is also nated with a dynamic nat from inside to dmz and when I hit on the dmz ip from my inside it works fine.
The requirement for us is that the users sitting behind the inside (i.e. LAN) should access the server on the public ip address and not thru the dmz.
I have deployed a read only domain controller in our DMZ as part of a domain-related project. That machine needs to be able to reach domain controllers on our internal network. To do so, it should traverse our ASA 5510, going from the DMZ Interface (security level set to 60) to the Inside Interface (security level set to 99).
I've created an ACL as following (alerting hostnames in the example):
access-list dmz_access_in extended permit ip host dmz.rodc.domain.local object-group int-domain-controllers
I've read in various spots that you have to create a NAT when traversing security levels, going from a less trusted interface (DMZ) to a more trusted one (internal.) Since this link will carry domain traffic, we do not want to create a real translation. Thus, I created a stand-in NAT that points to its own IP as follows:
static (dmz,inside) dmz.rodc.domain.local dmz.rodc.domain.local netmask 255.255.255.255
Long story short, the connection fails. I'm able to access other hosts in the DMZ and on another interface configured with the same security level (which I've explicitly allowed), but trying to go from the less-trusted DMZ to the more-trusted internal fails.
configure ASA 5510 as below
inside users should communicate with Hosts on the DMZ Zone and at the same time they should go for internet towards outside interface
ASA with 8.3(1)
default security levels
attached is the digram for your reference need communicate form inside to DMZ
One Host on inside network needs to access customized application hosted on Internet. Its a customized application run on port 80, 443, 5000-to-50020
How do I allow this host access for this specific application. I got ASA 5510 and host is in the inside network, we also got an ACL on inside interface to have control.
-Host IP on inside network - 172.16.30.15
-Application to access - 74.219.x.x
-Inside ACL name - inside-acl
we have hosted voip and would like have our internet as back for their router. We gave them public static ip so they can configure that in their router. How can i configure the ip address in our firewall let say on asa5510 ethernet port 3 so if their router T1 goes out then our internet will work as backup.
View 4 Replies View RelatedI am now using ASA 5510 as a firewall device.I have configured 3 interfaces ethernet 0/0,ethernet 0/1,ethernet 0/2 as Wan interface, DMZ interface and Internal Lan interface. Internet is working fine from LAN as well as DMZ.The WAN interface use the Public Point 2 point IP(/30) Provided by the ISP and another pool of Public Ip is also provided by the ISP (/28). Now I want to Map the /28 IP to some servers in DMZ . DMZ servers currently have 192.168.101.0/27 private IP . Now the problem is how to Map the Public IP to those Private IP in DMZ servers.
View 9 Replies View Relatedi just got an extra public subnet from our ISP (co hosting center) But I can't figure out how to use them on my ASA.
New:
IP-adresses: 87.1.1.194 - 87.1.1.254
Default gateway: 87.1.1.193
Subnetmask: 255.255.255.192
Old:
IP-adresses: 200.1.1.34 - 200.1.1.46
Default gateway: 200.1.1.33
Subnetmask: 255.255.255.240
Config:
route wan 0.0.0.0 0.0.0.0 200.1.1.33 1
And statics like:
static (interface,wan) tcp 200.1.1.37 3389 192.168.3.100 3389 netmask 255.255.255.255
We have the setup as shown above, our requirement is to access mail server via ports smtp and pop3.But as the mailserver is hosted at internet users at site were not able to aceess. we need to nat a intranet ip with mail server ip and mail server ip back to intranet ip and provide the access.We use ASA 5510 firewall.
View 7 Replies View RelatedI have DMZ n/w 192.166.0.0/24 on which i have nated on public ip
-private ip : 192.16.0.201 (OWA)
-public ip : 61.x.x.x.
when i try to access owa(public ip ) from dmz it is not allowing , From what rules i need to set to get work ASA 5510 8.2
We have an issue with some NAT on an ASA 5510. Here is a simplified drawing of the ASA setup:So the issue is when we try to send traffic from 172.16.3.251 to 1.1.1.1 we got this message in the log:
Oct 18 2011 12:32:12: %ASA-3-305006: portmap translation creation failed for udp src inside
172.16.3.251 /37166 dst outside:1.1.1.1/23
It looks like there is an issue with NAT but maybe is cause of the DUAL ISP setup as packets are routed through the outside interface and not IPtelefoni_outisde?
I have a new 5510 which I have upgraded to 8.4(3). I have a /29 subnet from the telco on my outside interface. I have 6 subinterfaces on a dot1Q trunk on my inside interface. The customer requirement is to have two servers in a DMZ which have public IP's from the /29 subnet. The customer will not give the servers a new IP address so we are stuck with the two public IPs in the DMZ. I thought I would need a bridge group and bridge the outside, two DMZ interfaces but I read that bridging requires the firewall to be in transparent mode and then it won't support VPNs - this is not an option as I need to terminate VPNs on the box too.
how can I accommodate the two servers in the DMZ with public IPs whilst the ASA is in routed mode ?
I have a mail archiver (hardware device) in my network that I need to access to from the Ipad/iphone. There is an app for it but I have to allow the access on the ASA. I created an 'object' for the device and added a Static NAT entry for it, then added an access rule. Its not working so I am guessing I did it wrong. The device uses port 8000 which I also added to the object. correct commands, or using the ASDM works too.
View 1 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View Relatedi have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
I have a Cisco ASA 5510 configured to access the internet, with an:
inside interface (ethernet 0/1) 130.130.0.254 and outside interface (ethernet 0/0) x.x.x.x
I have now configured another inside interface (ethernet0/2) on ASA with the IP 172.16.0.254 and I have connected it directly to another switch with a management IP 172.16.0.5.
The problem is that the two inside interfaces (130.130.0.254 &172.16.0.254) cannot communicate with each other thus the e0/2 172.16.0.254 interface cannot access the internet.
I am setting up a new ASA 5510 on our inside network so that we can terminate our VPN connections on this ASA. I can get the VPN to work fine however I noticed that once I turned on my VPN profiles now when I try to access the ASDM I'm getting the VPN logon page. So I decided that in order to resolve this I need a separate interface dedicated to management of my ASA.
I'm trying to come up with the best way to do this. I've got two ports on the ASA plugged into my core switch. One is on a separate VLAN from the rest of my network traffic. This is the port I want to use for management. The second will be used to route all of my VPN traffic.
So far I haven't been able to get this to work at all. My thought was that it had to do with routes, NAT and ACLs. I've been playing with them but can't get any combination to work.
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
Im having problems with google saying we generate to much traffic to [URL]
I need to know which machines on the inside are talking so much with google. Can this be done via ASA 5510? do i need a third party program for this?
I have a situation where we have a single DMZ server currently statically forwarded to a single public IP. TCP ports 80, 443, 8080, 8500, 53, and 21 are open to this server via an access list.
However, we have added an additional server to the DMZ, and because our web developers did not communicate with me beforehand, we are forced to use the same DNS name (thus, the same piblic IP) for this server. This server only needs traffic on TCP/8800 forwarded to it.
I am using ASDM 6.4 for configuration of this, as I am required to take multiple screen shots of the procedure for our change control policy.
My question lies in the reconfiguration of NAT/ PAT. Since our current server has a single static NAT to a single public IP, it is simply natted for "any" port. I understand that I can add the new server as an object, and only PAT it on TCP 8800, but will I then have to go back and reconfigure the first server multiple times for PAT, or will the ASA notice the specific PAT, and forward 8800 to the new server without affecting the existing "old" server?
It appears ASDM will not allow me to put multiple ports into a single network object. I am assuming I will need to add 6 separate object translations for the "old" server based on TCP port, and 1 object translation for the "new" server, correct?
I have a few devices that the manufacturer told us we have to set with a public IP (No Natting) We have Internet ->ASA5510-> Switch 3550 with 3 vlans. Up to now we have always use Natting to configure internet access to specific devices. I heard setting up a witch with one VLAN connected to the internet and all other internals is a bad idea. that was the only Idea we had.
View 3 Replies View RelatedI've tried a bunch things but it didn't work, I'm about to gave up! :-/
I have the following scenario:
ASA5510 - v8.3(2)
Interfaces
ETH0/0 = outside = 189.xxx.xxx.129
ETH0/1 = inside = 10.xx.1.15
[Code]....
What should I do to get the SIP and 8080 port working on my Public IP, likewise just as access from my browse the http://189.xxx.xxx.129:8080 and get through directly to my internal server 10.xx.xx.61 ?