I have a few devices that the manufacturer told us we have to set with a public IP (No Natting) We have Internet ->ASA5510-> Switch 3550 with 3 vlans. Up to now we have always use Natting to configure internet access to specific devices. I heard setting up a witch with one VLAN connected to the internet and all other internals is a bad idea. that was the only Idea we had.
View 3 Replies how to configure public ip on router 1841 and ASA 5510. let me show you my issue that: i have router 1841 ( for F0/0 use pubic ip add 10.10.10.1 /30, and F0/1 use other rang public ip add 20.20.20.1 /24) and on ASA 5510 i use public ip add E0/0 20.20.20.2 /24 ) all this for public ip add and my lan ip is 192.168.0.1/24.
could you let me know how to configure on router 1841 and ASA 5510. for router 1841 if you use private ip we can use nat but for all public ip add how can we do it?
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
View 1 Replies View Relatedwe have hosted voip and would like have our internet as back for their router. We gave them public static ip so they can configure that in their router. How can i configure the ip address in our firewall let say on asa5510 ethernet port 3 so if their router T1 goes out then our internet will work as backup.
View 4 Replies View RelatedI am now using ASA 5510 as a firewall device.I have configured 3 interfaces ethernet 0/0,ethernet 0/1,ethernet 0/2 as Wan interface, DMZ interface and Internal Lan interface. Internet is working fine from LAN as well as DMZ.The WAN interface use the Public Point 2 point IP(/30) Provided by the ISP and another pool of Public Ip is also provided by the ISP (/28). Now I want to Map the /28 IP to some servers in DMZ . DMZ servers currently have 192.168.101.0/27 private IP . Now the problem is how to Map the Public IP to those Private IP in DMZ servers.
View 9 Replies View Relatedi just got an extra public subnet from our ISP (co hosting center) But I can't figure out how to use them on my ASA.
New:
IP-adresses: 87.1.1.194 - 87.1.1.254
Default gateway: 87.1.1.193
Subnetmask: 255.255.255.192
Old:
IP-adresses: 200.1.1.34 - 200.1.1.46
Default gateway: 200.1.1.33
Subnetmask: 255.255.255.240
Config:
route wan 0.0.0.0 0.0.0.0 200.1.1.33 1
And statics like:
static (interface,wan) tcp 200.1.1.37 3389 192.168.3.100 3389 netmask 255.255.255.255
We have the setup as shown above, our requirement is to access mail server via ports smtp and pop3.But as the mailserver is hosted at internet users at site were not able to aceess. we need to nat a intranet ip with mail server ip and mail server ip back to intranet ip and provide the access.We use ASA 5510 firewall.
View 7 Replies View RelatedI have DMZ n/w 192.166.0.0/24 on which i have nated on public ip
-private ip : 192.16.0.201 (OWA)
-public ip : 61.x.x.x.
when i try to access owa(public ip ) from dmz it is not allowing , From what rules i need to set to get work ASA 5510 8.2
We have an issue with some NAT on an ASA 5510. Here is a simplified drawing of the ASA setup:So the issue is when we try to send traffic from 172.16.3.251 to 1.1.1.1 we got this message in the log:
Oct 18 2011 12:32:12: %ASA-3-305006: portmap translation creation failed for udp src inside
172.16.3.251 /37166 dst outside:1.1.1.1/23
It looks like there is an issue with NAT but maybe is cause of the DUAL ISP setup as packets are routed through the outside interface and not IPtelefoni_outisde?
I have a new 5510 which I have upgraded to 8.4(3). I have a /29 subnet from the telco on my outside interface. I have 6 subinterfaces on a dot1Q trunk on my inside interface. The customer requirement is to have two servers in a DMZ which have public IP's from the /29 subnet. The customer will not give the servers a new IP address so we are stuck with the two public IPs in the DMZ. I thought I would need a bridge group and bridge the outside, two DMZ interfaces but I read that bridging requires the firewall to be in transparent mode and then it won't support VPNs - this is not an option as I need to terminate VPNs on the box too.
how can I accommodate the two servers in the DMZ with public IPs whilst the ASA is in routed mode ?
Im having problems with google saying we generate to much traffic to [URL]
I need to know which machines on the inside are talking so much with google. Can this be done via ASA 5510? do i need a third party program for this?
I have a situation where we have a single DMZ server currently statically forwarded to a single public IP. TCP ports 80, 443, 8080, 8500, 53, and 21 are open to this server via an access list.
However, we have added an additional server to the DMZ, and because our web developers did not communicate with me beforehand, we are forced to use the same DNS name (thus, the same piblic IP) for this server. This server only needs traffic on TCP/8800 forwarded to it.
I am using ASDM 6.4 for configuration of this, as I am required to take multiple screen shots of the procedure for our change control policy.
My question lies in the reconfiguration of NAT/ PAT. Since our current server has a single static NAT to a single public IP, it is simply natted for "any" port. I understand that I can add the new server as an object, and only PAT it on TCP 8800, but will I then have to go back and reconfigure the first server multiple times for PAT, or will the ASA notice the specific PAT, and forward 8800 to the new server without affecting the existing "old" server?
It appears ASDM will not allow me to put multiple ports into a single network object. I am assuming I will need to add 6 separate object translations for the "old" server based on TCP port, and 1 object translation for the "new" server, correct?
I've tried a bunch things but it didn't work, I'm about to gave up! :-/
I have the following scenario:
ASA5510 - v8.3(2)
Interfaces
ETH0/0 = outside = 189.xxx.xxx.129
ETH0/1 = inside = 10.xx.1.15
[Code]....
What should I do to get the SIP and 8080 port working on my Public IP, likewise just as access from my browse the http://189.xxx.xxx.129:8080 and get through directly to my internal server 10.xx.xx.61 ?
We need to deploy a Cisco ASA 5510 behind the Internet facing router for Remote Access VPN (RAVPN). We bought the block of 16 IPs (in a different subnet) which is routed through the main router (69.x.x.x)and configured the outside interface of ASA with a public IP 64.x.x.x and subnet mask 255.255.255.240. Below is the network structure.
But, we can't access the ASA by it's public IP.
DSL Modem → RV082 router → Switch → LAN
(69.x.x.x) ↑ (192.168.0.0)
Cisco ASA 5510
(outside: 64.x.x.x, inside: 192.168.0.172)
I'm currently replacing my ASA 5505 with a 5510. I have a range of public IP addresses, one has been assigned to the outside interface by the setup wizard (e.g. 123.123.123.124 ) and another I would like to NAT to an internal server (e.g 192.168.0.3 > 123.123.123.125). On my asa 5505 this seemed fairly straigh forward, i.e. create an incoming access rule that allowed SMTP to 123.123.123.125 and then create a static nat to translate 192.168.0.3 to 123.123.123.125. Since I've tried to do the same on the 5510 traffic is not passing through so I'm assuming that the use of additional public IP addresses is not handled in the same way as the 5505? I also see that by default on the 5505, 2 VLANs are created, one for the inside and one for the outside, where as this is not the case on the 5510. Is the problem that VLANs or sub-interfaces need to be created first? I'm doing the config via ASDM.
Everything else seems to OK i.e. access to ASDM via 123.123.123.124, outbound PAT and the site-to-site VPN.
I have a Cisco ASA 5510 that was set up as a VPN server for working remote. I have disabled split tunneling so that all traffic created while VPN'd in goes through the ASA. The problem I'm having I believe would be resolved if I enabled split tunneling but I would prefer another solution. Now..for the problem.When a user is connected via VPN, they can hit all intended devices both public and private accept servers that have static NATs in the FW. So Server A has a public of 1.1.1.1 which is one to one mapped to private address of 10.1.1.1. Now if the remote user brings up a browser and goes to 1.1.1.1 it wont work. The FW gives me a error which is posted below. However, using the private IP of the server works. I thought about trying to manipulate DNS to resolve this as the remote users are using URLs and not IPs when trying to reach these servers but again, was hoping I could resolve the NAT problem that the FW seems to be having.
Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src Outside:192.168.202.100/49238 dst INSIDE:1.1.1.1/80 denied due to NAT reverse path failure 192.168.202.x/24 is the remote vpn ip given via the ASA.
Here are some configurations on the ASA:
static (INSIDE,Outside) 1.1.1.1 10.1.1.1 netmask 255.255.255.255
access-list INSIDE_nat0_outbound extended permit ip object-group DM_INLINE_NETWORK_2 192.168.202.0 255.255.255.0
object-group network DM_INLINE_NETWORK_2
[code].....
Outside with 4.4.4.4 as the public ip traffic gets NAT'd do dynamically Inside with 10.1.1.x network on it.The ASA is running 8.2
getting my additional IP addresses working on my ASA 5510. I have a /29 allocation and outbound access and inbound access to my internal www server is working fine through the default outside interface. However, I now need to setup a second IP address that maps internally to a different web server. When I setup a new network object with automatic NAT translation to the new IP address, it does not work. If I setup the same scenario using the outside interface, it works fine. What is the proper way to setup additional IP address on my ASA v8.4?
View 10 Replies View RelatedI hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 Replies View RelatedWill I break anything if I create a second IP address on the physical external interface of our ASA 5510? I want to point it nowhere internally but want an active interface that can be vulnerability scanned but won't lead anywhere internally.
View 9 Replies View RelatedI have one public IP address but multiple local servers that run on the same port. I cannot change the port the clients use to connect to this server, so I can't do a port map in my NAT router. The solution I had in mind, is to filter on source address. If a client from public IP X.X.X.X connects to port Z, I want it to go to internal server 10.10.10.10 and if a client from public IP Y.Y.Y.Y connects to port Z, I want it to go to internal server 10.20.20.20. Is this possible? I'm using an ASA5510 but I could also switch to a 5505 for this.
View 3 Replies View RelatedI have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
how to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies View RelatedI am working on a task of redirecting any unmatched http traffic to Symantec public transparent proxy through Cisco ASA. For the definition of uncatched http traffic, we have inbound squid servers for deploying IE proxy pac and redirect the http traffic to Symantec public transpraent proxy, however we can't deploy IE proxy pac to mobile device and non-support web browers.Since we have some application using IE proxy setting for direct http communication with external domains, the current symantec policy addes those domains in the exception list so that they are not redirect to Symantec public transparent proxy server.
-For the platform - Cisco ASA 5510 ASA 8.4(4)1
-For the solution, I have the following two nat rules
How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View RelatedThis is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedI'm having a problem configuring an ASA 5510. A previous employee started the config and left abruptly. He established a VPN Tunnel between two of our sites and that's working without an issue. The problem is, the network behind the 5510 at the remote location cannot access the internet.
ASA Version 8.2(1)
!
hostname PH-Firewall
domain-name pleasehelpme.com
enable password HXrQty4kqW8s8yeE encrypted
passwd ucA.qrYJWD9UyIFz encrypted
names
[code]....
I am confiuging a DMZ on my ASA 5510 but I have run out of physical ports, since I have dual Wan ports configured. I plan to implement a DMZ using subinterfaces. I have 2 questions:
1) Do I need to configure a Vlan to complete this task?
2) Do I need to re-configure the other interfaces for subinterfaces and/or vlans as well?
I'm trying to configure an asa 5510 8.2(1)?I have a range of pub ips 3*.108.234.145-150
>>> E0/0 3*.108.234.146 outside public
>>> E0/1 192.168.1.1 inside
>>> E0/2 192.168.3.1 dmz
would like to map dmz host 192.168.3.107 to external 3*.108.234.147 on port 5000 and 50001 LOCAL LAN should also be able to get to dmz host ports.i've tried a few configs and also following this example:
[URL]
without any luck, here is my config, also posted the out put of show arp which is able to see and ping the host on dmz, also the output of show access-list which shows hits to it.
prophase-pix(config-if)# show running-config
: Saved
:
ASA Version 8.2(1)
!
hostname prophase-pix
enable password encrypted
[code]....
I am absolutely new in the enterprise firewall world but I would like to start learning how to configure ASA 5505 and 5510. I did some research myself and I found that the material or the topic itself is a huge adventure (lots to read and understand). My company uses IOS versions until 8.2 due to the differences in the NAT-ting rules with 8.3 and 8.4.
View 1 Replies View RelatedI need to allow connection from IPHONE (in Internet) to connect Exchange on private network, synchronising with activesync (https) We have a microsoft TMG on frontal (inside network)
What is the method to parameter CISCO ASA using clientless access: Port forwardind? smarttunnel, web proxy? Nat?
i want the activesync request to cross ASA to go directly on TMG without asking password and user
I recently bought an all brand new ASA 5510 and it is here by my side. I'm trying to configure it but when entering https://192.168.1.1/admin I get Page Not Found error on IE. I'm able to ping 192.168.1.1 and have success telnet 443 port.
View 13 Replies View RelatedHave a new ASA 5510 connected to the laptop via console. I need to load the IOS and the configure from another ASA. I have tftp client on the laptop. Do I just need to set the inside IP to the same subnet as my laptop? Will I need a crossover cable?
View 1 Replies View RelatedI have an ASA 5510 and I can not configure fine.
My problem is that I have 10 public address connected to ASA and each public address is redirectioned to an internal IP address.
An of these public address is the ip address of mi ASA.
how to configure and access-list and an NAT, the others I will configure.
interface Ethernet0/0
description Interface_WAN_World-Ttrends
speed 100
duplex full
nameif outside(code)