Cisco Firewall :: 5510 - ASA 8.4 - How To Setup Additional Public IP's On Outside Interface
May 10, 2012
getting my additional IP addresses working on my ASA 5510. I have a /29 allocation and outbound access and inbound access to my internal www server is working fine through the default outside interface. However, I now need to setup a second IP address that maps internally to a different web server. When I setup a new network object with automatic NAT translation to the new IP address, it does not work. If I setup the same scenario using the outside interface, it works fine. What is the proper way to setup additional IP address on my ASA v8.4?
View 10 Replies
ADVERTISEMENT
Jul 31, 2012
I have run out of public facing IP addresses and I need more. Assuming I have been issued 1.1.1.0/24 and my new/additional range/subnet issued is 2.2.2/0/24 - Can I carry on with the same configuration on my ASA5510 and just add static NAT for new services in the 2.2.2.0/24 range.
i.e.existing config
route 0.0.0.0 0.0.0.0 1.1.1.254 (upstream ISP)
Interface outside ip address 1.1.1.1 255.255.255.0
NAT 2.2.2.1 to 10.1.2.3
or, assume my ISP will deliver 2.2.2.1 to my outside interface (1.1.1.1.1/24) and if my NAT is in place it will get delivered to 10.1.2.3 inside.
or, put another way I dont need change my set-up as I just static route to my ISP!
my real public IP is a /27 can I use my broadcast address (its a legit public IP address)?
i.e 1.2.3.0/27 = 1.2.3.1 to 1.2.3.31
Outside interface = 1.2.3.1/27
Can I use 1.2.3.31 and NAT it to an internal server?
View 3 Replies
View Related
Mar 16, 2011
we have hosted voip and would like have our internet as back for their router. We gave them public static ip so they can configure that in their router. How can i configure the ip address in our firewall let say on asa5510 ethernet port 3 so if their router T1 goes out then our internet will work as backup.
View 4 Replies
View Related
Oct 12, 2011
how to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies
View Related
Jun 4, 2013
Our ASA 5510 was configured with a public interface, a DMZ interface, and a private interface. I have a remote access VPN using AnyConnect client and LDAP authentication for Active Directory. We are changing ISP (groan!), which means all new public IP addresses. The new circuit is installed, so I have a second public interface (same security level as the first public interface, wholly different IP address range) enabled on the ASA. I hope to transition whatever I can, which means get the VPN access through either public interface. Can I just enable client access on the second public interface at the Anyconnect Connection Profiles tab in ASDM? That seems too simple. Can they share the one address pool?
View 1 Replies
View Related
Jul 22, 2012
I am now using ASA 5510 as a firewall device.I have configured 3 interfaces ethernet 0/0,ethernet 0/1,ethernet 0/2 as Wan interface, DMZ interface and Internal Lan interface. Internet is working fine from LAN as well as DMZ.The WAN interface use the Public Point 2 point IP(/30) Provided by the ISP and another pool of Public Ip is also provided by the ISP (/28). Now I want to Map the /28 IP to some servers in DMZ . DMZ servers currently have 192.168.101.0/27 private IP . Now the problem is how to Map the Public IP to those Private IP in DMZ servers.
View 9 Replies
View Related
Aug 31, 2011
i just got an extra public subnet from our ISP (co hosting center) But I can't figure out how to use them on my ASA.
New:
IP-adresses: 87.1.1.194 - 87.1.1.254
Default gateway: 87.1.1.193
Subnetmask: 255.255.255.192
Old:
IP-adresses: 200.1.1.34 - 200.1.1.46
Default gateway: 200.1.1.33
Subnetmask: 255.255.255.240
Config:
route wan 0.0.0.0 0.0.0.0 200.1.1.33 1
And statics like:
static (interface,wan) tcp 200.1.1.37 3389 192.168.3.100 3389 netmask 255.255.255.255
View 22 Replies
View Related
Sep 5, 2012
We have the setup as shown above, our requirement is to access mail server via ports smtp and pop3.But as the mailserver is hosted at internet users at site were not able to aceess. we need to nat a intranet ip with mail server ip and mail server ip back to intranet ip and provide the access.We use ASA 5510 firewall.
View 7 Replies
View Related
Mar 3, 2013
I have DMZ n/w 192.166.0.0/24 on which i have nated on public ip
-private ip : 192.16.0.201 (OWA)
-public ip : 61.x.x.x.
when i try to access owa(public ip ) from dmz it is not allowing , From what rules i need to set to get work ASA 5510 8.2
View 13 Replies
View Related
Oct 17, 2011
We have an issue with some NAT on an ASA 5510. Here is a simplified drawing of the ASA setup:So the issue is when we try to send traffic from 172.16.3.251 to 1.1.1.1 we got this message in the log:
Oct 18 2011 12:32:12: %ASA-3-305006: portmap translation creation failed for udp src inside
172.16.3.251 /37166 dst outside:1.1.1.1/23
It looks like there is an issue with NAT but maybe is cause of the DUAL ISP setup as packets are routed through the outside interface and not IPtelefoni_outisde?
View 13 Replies
View Related
May 7, 2012
I have a new 5510 which I have upgraded to 8.4(3). I have a /29 subnet from the telco on my outside interface. I have 6 subinterfaces on a dot1Q trunk on my inside interface. The customer requirement is to have two servers in a DMZ which have public IP's from the /29 subnet. The customer will not give the servers a new IP address so we are stuck with the two public IPs in the DMZ. I thought I would need a bridge group and bridge the outside, two DMZ interfaces but I read that bridging requires the firewall to be in transparent mode and then it won't support VPNs - this is not an option as I need to terminate VPNs on the box too.
how can I accommodate the two servers in the DMZ with public IPs whilst the ASA is in routed mode ?
View 1 Replies
View Related
Jul 9, 2012
I have a Cisco ASA 5520 (Ver 8.2(4)) with all four interfaces in use (Public, Private, DMZ, Local offices) and an IPS module, so there are no spare interfaces. I have used all of Public IP's on the current interface for various services (these need one to one mapping, so I can't port map mainly due to SSL certificate issues) and I need to add another Public IP range. The secondary option on ASA interfaces does not exist as on routers/switches and I need to use an additional non contiguous IP address range for additional services advertised on the Public interface that are NAT'd to be servers in my DMZ.
I have seen an example of adding a static arp on the Private interface to allow a secondary gateway to be used for outbound traffic, but I need to allow 14 new IP addresses to be NAT'd from the Public to DMZ and possibly also for outbound NAT'ing (from either Private or DMZ to the Public). I have a L2 switch between the ISP router and the firewall, so using VLAN's is not an option unless the ISP can be persuaded (highly unlikey) to add the seondary IP's as a sub interface with tagging. Anyway if this was actioned then we would have a massive outage on our current IP range during the transistion.
View 3 Replies
View Related
Mar 10, 2011
we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
View 1 Replies
View Related
Feb 19, 2013
Im having problems with google saying we generate to much traffic to [URL]
I need to know which machines on the inside are talking so much with google. Can this be done via ASA 5510? do i need a third party program for this?
View 1 Replies
View Related
Feb 5, 2012
I have a situation where we have a single DMZ server currently statically forwarded to a single public IP. TCP ports 80, 443, 8080, 8500, 53, and 21 are open to this server via an access list.
However, we have added an additional server to the DMZ, and because our web developers did not communicate with me beforehand, we are forced to use the same DNS name (thus, the same piblic IP) for this server. This server only needs traffic on TCP/8800 forwarded to it.
I am using ASDM 6.4 for configuration of this, as I am required to take multiple screen shots of the procedure for our change control policy.
My question lies in the reconfiguration of NAT/ PAT. Since our current server has a single static NAT to a single public IP, it is simply natted for "any" port. I understand that I can add the new server as an object, and only PAT it on TCP 8800, but will I then have to go back and reconfigure the first server multiple times for PAT, or will the ASA notice the specific PAT, and forward 8800 to the new server without affecting the existing "old" server?
It appears ASDM will not allow me to put multiple ports into a single network object. I am assuming I will need to add 6 separate object translations for the "old" server based on TCP port, and 1 object translation for the "new" server, correct?
View 6 Replies
View Related
Apr 13, 2013
I have a few devices that the manufacturer told us we have to set with a public IP (No Natting) We have Internet ->ASA5510-> Switch 3550 with 3 vlans. Up to now we have always use Natting to configure internet access to specific devices. I heard setting up a witch with one VLAN connected to the internet and all other internals is a bad idea. that was the only Idea we had.
View 3 Replies
View Related
Sep 18, 2012
I've tried a bunch things but it didn't work, I'm about to gave up! :-/
I have the following scenario:
ASA5510 - v8.3(2)
Interfaces
ETH0/0 = outside = 189.xxx.xxx.129
ETH0/1 = inside = 10.xx.1.15
[Code]....
What should I do to get the SIP and 8080 port working on my Public IP, likewise just as access from my browse the http://189.xxx.xxx.129:8080 and get through directly to my internal server 10.xx.xx.61 ?
View 5 Replies
View Related
Oct 30, 2012
Got an ASA5525-X with 8.6 release. We have an inside interface (10.11.1.0/24) and a DMZ interface (10.254.1.0/24). On that DMZ interface theres an SMTP server; by using the Public server feature in ASDM we created a rule so we have mapped the 10.254.1.29 internal ip to an external ip 217.x.x.x Everything is fine; working ok, but for several reasons we need to access the public ip 217.x.x.x from an inside ip (10.11.1.10). I tried to do it by creating an exemption for the dynamic nat; if i don't do that i have a 'deny ip spoof from...' message rolling on my syslogs.Seems to do the trick.....but only for pings! i ping the public ip from the inside ip, and got the reply from the internal ip on the DMZ. But if i want to telnet port 25 from inside to public; its not working.
View 7 Replies
View Related
Oct 8, 2012
Setup:
LAN (192.168.1.X, with .3 as gateway)
DMZ (192.168.2.X with .1 as gateway)
WAN (X.X.X.146 as primary public IP, .145 as gateway and .147-150 as additional public IPs)
I want to set it up so that X.146 is where all my outbound traffic appears to originate.I want tcp HTTPS and SMTP to be allowed from the WAN (via the X.147 IP) to a specific server (192.168.1.11) on the LAN.Also, HTTP traffic to X.148, X.149 and X.150 should go to DMZ and 192.168.2.8, 192.168.2.15 and 192.168.2.18 respectively, but I haven't added that to my config yet. Looking to get the HTTPS and SMTP ones working first, then I'll fix the others (one step at a time)I've got contact with the outside world when I've configured it using the ASDMs "Public Server" interface, but it refuses to properly establish the connection, I get a "SYN timeout".
My config:
: Saved
:
ASA Version 8.2(5)
!
hostname kcisco
enable password X encrypted
passwd X encrypted
names
[code]....
View 7 Replies
View Related
Feb 5, 2012
We need to deploy a Cisco ASA 5510 behind the Internet facing router for Remote Access VPN (RAVPN). We bought the block of 16 IPs (in a different subnet) which is routed through the main router (69.x.x.x)and configured the outside interface of ASA with a public IP 64.x.x.x and subnet mask 255.255.255.240. Below is the network structure.
But, we can't access the ASA by it's public IP.
DSL Modem → RV082 router → Switch → LAN
(69.x.x.x) ↑ (192.168.0.0)
Cisco ASA 5510
(outside: 64.x.x.x, inside: 192.168.0.172)
View 16 Replies
View Related
Dec 2, 2010
I'm currently replacing my ASA 5505 with a 5510. I have a range of public IP addresses, one has been assigned to the outside interface by the setup wizard (e.g. 123.123.123.124 ) and another I would like to NAT to an internal server (e.g 192.168.0.3 > 123.123.123.125). On my asa 5505 this seemed fairly straigh forward, i.e. create an incoming access rule that allowed SMTP to 123.123.123.125 and then create a static nat to translate 192.168.0.3 to 123.123.123.125. Since I've tried to do the same on the 5510 traffic is not passing through so I'm assuming that the use of additional public IP addresses is not handled in the same way as the 5505? I also see that by default on the 5505, 2 VLANs are created, one for the inside and one for the outside, where as this is not the case on the 5510. Is the problem that VLANs or sub-interfaces need to be created first? I'm doing the config via ASDM.
Everything else seems to OK i.e. access to ASDM via 123.123.123.124, outbound PAT and the site-to-site VPN.
View 15 Replies
View Related
Mar 12, 2012
I have a Cisco ASA 5510 that was set up as a VPN server for working remote. I have disabled split tunneling so that all traffic created while VPN'd in goes through the ASA. The problem I'm having I believe would be resolved if I enabled split tunneling but I would prefer another solution. Now..for the problem.When a user is connected via VPN, they can hit all intended devices both public and private accept servers that have static NATs in the FW. So Server A has a public of 1.1.1.1 which is one to one mapped to private address of 10.1.1.1. Now if the remote user brings up a browser and goes to 1.1.1.1 it wont work. The FW gives me a error which is posted below. However, using the private IP of the server works. I thought about trying to manipulate DNS to resolve this as the remote users are using URLs and not IPs when trying to reach these servers but again, was hoping I could resolve the NAT problem that the FW seems to be having.
Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src Outside:192.168.202.100/49238 dst INSIDE:1.1.1.1/80 denied due to NAT reverse path failure 192.168.202.x/24 is the remote vpn ip given via the ASA.
Here are some configurations on the ASA:
static (INSIDE,Outside) 1.1.1.1 10.1.1.1 netmask 255.255.255.255
access-list INSIDE_nat0_outbound extended permit ip object-group DM_INLINE_NETWORK_2 192.168.202.0 255.255.255.0
object-group network DM_INLINE_NETWORK_2
[code].....
Outside with 4.4.4.4 as the public ip traffic gets NAT'd do dynamically Inside with 10.1.1.x network on it.The ASA is running 8.2
View 2 Replies
View Related
Sep 11, 2012
I hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 Replies
View Related
Mar 15, 2011
Will I break anything if I create a second IP address on the physical external interface of our ASA 5510? I want to point it nowhere internally but want an active interface that can be vulnerability scanned but won't lead anywhere internally.
View 9 Replies
View Related
Dec 27, 2011
I have one public IP address but multiple local servers that run on the same port. I cannot change the port the clients use to connect to this server, so I can't do a port map in my NAT router. The solution I had in mind, is to filter on source address. If a client from public IP X.X.X.X connects to port Z, I want it to go to internal server 10.10.10.10 and if a client from public IP Y.Y.Y.Y connects to port Z, I want it to go to internal server 10.20.20.20. Is this possible? I'm using an ASA5510 but I could also switch to a 5505 for this.
View 3 Replies
View Related
Jul 30, 2012
I have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
View 1 Replies
View Related
Sep 4, 2012
I am working on a task of redirecting any unmatched http traffic to Symantec public transparent proxy through Cisco ASA. For the definition of uncatched http traffic, we have inbound squid servers for deploying IE proxy pac and redirect the http traffic to Symantec public transpraent proxy, however we can't deploy IE proxy pac to mobile device and non-support web browers.Since we have some application using IE proxy setting for direct http communication with external domains, the current symantec policy addes those domains in the exception list so that they are not redirect to Symantec public transparent proxy server.
-For the platform - Cisco ASA 5510 ASA 8.4(4)1
-For the solution, I have the following two nat rules
View 10 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Aug 25, 2011
at the moment we are using as default the manager interface as ap-manager interface.
Now I have to change the IP. I would like to change that very smooth with all our locations. My question, is it possible to add a ap-manager interface with a new vlan and IP Range, so that I can move the AP's to the second interface as as soon as it is planed with the location. Sometimes in special cases we have hard coded the WLC IP oder we just need to change the DHCP option but this needs to be planed and I see problem to do that in a hard cut.
View 11 Replies
View Related
Jul 29, 2012
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
View 8 Replies
View Related
Mar 20, 2011
Have an ASA 5510. Setting up a new DMZ zone for wireless and it will only have Internet access. What are the steps so that users on this new DMZ subnet can VPN into the Outside interface on the same ASA?
View 4 Replies
View Related
May 5, 2011
I will be adding wireless access points or repeaters on a business network. The business already has one wireless router using a https login, that 15 computers are wired to, through switches. This Secure http router is directly connected to the cable modem.Would I be loosing the benefit of Secure http by adding wireless access points or repeaters that don't support it? Or would they be securely routed by the main https router connected to the gateway?I have never had the opportunity to work with a secure http router before.
View 4 Replies
View Related
Apr 28, 2013
We've never had to do this before: best practice on setting up an additional subnet on a physical network?
For example, main network is 10.1.1.1, we need to setup an additional 10.1.2.1 to support more devices. We need both subnets to see each other and the servers on 10.1.1.1. We also need the new subnet to have access to the internet.Equipment we have: HP 2824's (2 current VLAN's - second one is for phones) and Untangle for our firewall.
View 9 Replies
View Related
