Cisco Firewall :: Communication Between 2 Inside Interfaces On ASA 5510
Oct 23, 2011
I have a Cisco ASA 5510 configured to access the internet, with an:
inside interface (ethernet 0/1) 130.130.0.254 and outside interface (ethernet 0/0) x.x.x.x
I have now configured another inside interface (ethernet0/2) on ASA with the IP 172.16.0.254 and I have connected it directly to another switch with a management IP 172.16.0.5.
The problem is that the two inside interfaces (130.130.0.254 &172.16.0.254) cannot communicate with each other thus the e0/2 172.16.0.254 interface cannot access the internet.
View 5 Replies
ADVERTISEMENT
Mar 12, 2011
I configured ASA 5510 ...
Totally it had 5 ports..
How to provide communication between two different interfaces which had configured as same security level?
How many trunks will support ASA 5510 with base-license?
How to configure trunk to an interface with different VLNs( Router on a stick).
View 6 Replies
View Related
Mar 5, 2011
configure ASA 5510 as below
inside users should communicate with Hosts on the DMZ Zone and at the same time they should go for internet towards outside interface
ASA with 8.3(1)
default security levels
attached is the digram for your reference need communicate form inside to DMZ
View 1 Replies
View Related
Jun 11, 2013
I've been following most of the comments in regarding how to allow communication between two internal networks on a ASA5510 8.2.5 But I am still a little confused about to how to set my firewall. I made chages to it and still do not have the desired results.
I need to allow comunication between Interface 0/1 and Interface 0/2. See configuration file with fake or dummy ip address below.
ASA Version 8.2(5)
!
hostname ciscoasa
domain-name lxx.com
[Code].....
View 1 Replies
View Related
Mar 12, 2011
Is it possible to provide communication between two different interfaces which had configured as different security level in ASA 5510?
View 3 Replies
View Related
Dec 30, 2012
I have a Cisco ASA 5510 with 3 inside interfaces each connected to a 3750X switch port in a vlan. Outside interface is connected to external router with 209.155.x.x public IP. Static route exists for outbound traffic on outside interface.
3750X is configured for inter-vlan routing. VLANs 10, 20, and 30 have 172.16.x.1 IP address with static routes pointing to the each of the ASA inside interfaces - 172.16.x.254. Connected hosts are configured with gateways pointing to the appropriate vlan interface IP - 172.16.x.1.
Inter-vlan routing appears to be working - I can ping back and forth between hosts on different vlans, and I can ping each vlan IP.I can also ping each ASA inside interface from a host in the appropriate vlan, but I cannot ping internet sites (4.2.2.2 or 8.8.8.8) from hosts on the inside interfaces.
I can ping 4.2.2.2 from the ASA CLI. I can ping internal hosts on vlans 10,20,30 from the ASA CLI. But, no luck with pinging from inside host to internet hosts
View 12 Replies
View Related
May 4, 2012
I have two inside interfaces (both security level 100) inside and inside110. Inside is 192.168.105.3/24 and inside110 is 192.168.110.3/24. I have a PC on the 192.168.105.0/24 network. I cannot ping the 192.168.110.3 IP of interface inside110.
View 2 Replies
View Related
Nov 30, 2011
ASA 5505 and DMZ, I have a Base License.
What do I need to do for access inside network to DMZ?
I successfully configure, internet Access for DZM and inside network, web server can be accessed from internet, but I have problem to configure communication from inside network to DMZ.
View 14 Replies
View Related
Nov 9, 2011
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 1 Replies
View Related
Sep 23, 2011
I have an ASA 5505 running 8.2(1), that is configured with three interfaces as follows:
Inside (security 100) 10.0.0.0 /24
Inside 2 (security 100) 192.168.0.0 /24
Outside (security 0) internet
Inside is connected to my internal network, inside 2 is connected to the network of a sister organization, outside is outside.
I'd like to be able to route between from inside to inside 2, and have NAT translate me to inside2's address.
I have inter-interface traffic configured, and when I use a NAT exemption, I can route fine. But the resources on network 2 must see my request as coming from the inside2 interface IP.
View 2 Replies
View Related
Mar 6, 2011
My customer is running an ASA5505 with 8.3 code.
The have a somewhat flaky proxy between their inside LAN and the firewall. I'd like to have a configuration as follows:
LAN > Proxy > VLAN 1 (eth0/2) on ASA
and
LAN > VLAN 1 (eth0/3) on ASA
So that in the event of Proxy failure (let's just say it loses power) the eth0/3 interface will kick in.
This appears to be easily configured according to the documentation:
"The following example creates two redundant interfaces:
hostname(config)# interface redundant 1
hostname(config-if)# member-interface gigabitethernet 0/0
hostname(config-if)# member-interface gigabitethernet 0/1
hostname(config-if)# interface redundant 2
hostname(config-if)# member-interface gigabitethernet 0/2
hostname(config-if)# member-interface gigabitethernet 0/3"
But these commands don't seem to be available on a 5505.
View 7 Replies
View Related
Oct 10, 2011
I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
View 11 Replies
View Related
Feb 20, 2013
Today I run into a problem with enabling ICMP traffice between two inside interfaces on ASA5510 (version 8.2). I tried to ping from 192.168.1.2 to 192.168.2.2 Failed. But I can visit outside websites or ping from any of the two addresses above to 8.8.8.8 So I checked the configuration shown as follow
<omitted>
interface ethernet0/1
nameif inside
[Code]....
View 3 Replies
View Related
Jun 20, 2012
I am setting up a network that will use the 1941 router with a cellular card (HWIC) to connect to the Internet for communication with remote stations in the field. The 1941 has a static IP address (166.142.xxx.yyy) on the Internet provided by the ISP (Verizon). The 1941 is connected via ethernet to the ASA5510. The end goal is to have the field cell routers (Digi Transport WR-44-R, also static IP) connect to the ASA5510 via VPN tunnels for communication back to the servers behind the firewall. I'm not sure exactly how to configure the 1941 so that the remote router can connect to the ASA using the public IP of the 1941 router. I have the 1941 working stand alone and can connect to the Internet and pass traffic, but I tried a static NAT to translate the public IP to the private IP of the ASA and cannot pass traffic. below is part of the 1941 configuration: [code]
Do I need to use VLAN bridging to accomplish the task or am I missing something with the NAT?
View 3 Replies
View Related
Jun 20, 2012
Can ASA sub-interfaces run separate IP Sec VPN tunnels eg
There are 02 sub-interfaces of 01 physical interface of Cisco ASA5510 [ASA Version 8.2(5)] and I need to run 01 IP Sec VPN tunnel on each of these
View 1 Replies
View Related
Sep 21, 2012
I have 2 dmz interfaces(dmz1 and dmz2) with security level 50. I am able to ping the hosts on dmz2 from dmz1. I am running a service on a dmz2 host on port 82 but i am not able to access that service from dmz1. Also, i have an inside interface at security lever 99 which is able to access that service.
Also, i have defined the following command to allow same security level communication.
same-security-traffic permit inter-interface
View 2 Replies
View Related
May 9, 2011
I have deployed a read only domain controller in our DMZ as part of a domain-related project. That machine needs to be able to reach domain controllers on our internal network. To do so, it should traverse our ASA 5510, going from the DMZ Interface (security level set to 60) to the Inside Interface (security level set to 99).
I've created an ACL as following (alerting hostnames in the example):
access-list dmz_access_in extended permit ip host dmz.rodc.domain.local object-group int-domain-controllers
I've read in various spots that you have to create a NAT when traversing security levels, going from a less trusted interface (DMZ) to a more trusted one (internal.) Since this link will carry domain traffic, we do not want to create a real translation. Thus, I created a stand-in NAT that points to its own IP as follows:
static (dmz,inside) dmz.rodc.domain.local dmz.rodc.domain.local netmask 255.255.255.255
Long story short, the connection fails. I'm able to access other hosts in the DMZ and on another interface configured with the same security level (which I've explicitly allowed), but trying to go from the less-trusted DMZ to the more-trusted internal fails.
View 12 Replies
View Related
Feb 15, 2012
We have ASA 5550, I have a citirx server in the dmz which is natted statically to a public ip address for port 443. The dmz server communicate with our internal server (i.e. AD) for LDAP authentication. I have a static transparent nat from inside to dmz for the internal server's communcation with dmz.
When accessing the application from inside the network on the internal web server it works perfectly fine and authenticates with the AD.But when accessing from outside, the reach the citrix server and then the AD authentication fails, basically it works intermitantly. I have tried to check the communcation from the DMZ server to the internal server and the icmp works perfectly fine, even I am able to telnet on the ports specified on the internal servers from the DMZ servers. I tried to look into the logs on the ASA and this is something that looks suspicious to me.
Feb 16 Teardown TCP connection 47646475 for dmz1:CITRIX-DMZ1/47179 to inside:inside-server/80 duration 0:00:00 bytes 1230 TCP FINs
Feb 16Built inbound TCP connection 47646476 for dmz1:CITRIX-DMZ1/47180 (CITRIX-DMZ1/47180) to inside:inside-server/80 (inside-server/80)
Feb 16Teardown TCP connection 47646476 for dmz1:CITRIX-DMZ1/47180 to inside:inside-server/80 duration 0:00:00 bytes 3824 TCP FINs
Feb 16Built inbound TCP connection 47646477 for dmz1:CITRIX-DMZ1/47181 (CITRIX-DMZ1/47181) to inside:inside-server/80 (inside-server/80)
Feb 16 Teardown TCP connection 47646477 for dmz1:CITRIX-DMZ1/47181 to inside:inside-server/80 duration 0:00:00 bytes 1224 TCP FINs
[code]....
View 2 Replies
View Related
Jan 5, 2013
I have ASA5510 with PLUSE License.I have 2 Inside interfaces as STAFF and MAIL and two Outside interface OUT_STAFF and OUT_MAIL which is in separate ISP's.now i want to nat STAFF to OUT_STAFF and MAIL to OUT_MAILbecause I'm having two default routes it gets impossible to do.
View 1 Replies
View Related
Feb 13, 2012
I have a question regarding firewall configurations. Is it possible to have two interfaces ( for two internet service providers) one for voice and one for data. Can I have two Outside Interfaces that one will apply to a pppoe client group and the other will apply to a static IP? Is this possible and if so What would be the steps on applying this connection? Also to note I have a point to point connection already established for the pppoe. I also have another point to point connection for data, but however I do not know how to apply this to the firewall.
View 3 Replies
View Related
Jan 15, 2013
I need to route to sub nets form 2 different ASA interfaces. The ASA also has an outside interface works like gateway for internet access. Here is my configuration:
ASA Version 8.2(1)
host name ICE3
names
interface Ethernet0/0
name if outside
security-level 0
ip address 201.199.xxx.xx 255.255.255.248
[Code]....
View 9 Replies
View Related
Nov 18, 2011
One Host on inside network needs to access customized application hosted on Internet. Its a customized application run on port 80, 443, 5000-to-50020
How do I allow this host access for this specific application. I got ASA 5510 and host is in the inside network, we also got an ACL on inside interface to have control.
-Host IP on inside network - 172.16.30.15
-Application to access - 74.219.x.x
-Inside ACL name - inside-acl
View 5 Replies
View Related
Apr 8, 2013
I am trying to setup intervlan routing with a Cisco ASA 5510 and two 2960-S switches. The 5510 currently is using ASA Version 7.0(2) and has a base license. I tried to create a sub interface today based on some info I found regarding the routing piece and it didn't recognize the command. I'm thinking I may need to update the IOS code or the license on the firewall. I know the syntax was correct because I looked it up and found it in a Cisco document.
View 15 Replies
View Related
Jun 10, 2013
we have two ASA 5510 connected in failover, and a pair of cisco 2960s switch connected in stack. Currently one interface of primary ASA is terminated on switch1 and a interface from standby is connected to switch2 as Inside, and switch1 and switch2 are in stack. for redundancy purpose i want to use multiple interfaces of ASA for inside , so first i thought to use etherchannel , but it has a limitation that , it cannot be terminated on stack switch(as per cisco document [URL]
So my question is :
1. can we use redundant interface feature where 2 physical interfaces combined to a redundant interface (eg interface redundant 1) for inside redundancy purpose.
2. Can these ports from primary/standby ASA terminated on stack switches (2960s), will this work (if the switch with active port goes down, will the other port take over in the redundant interface with the other switch).
View 1 Replies
View Related
Nov 13, 2011
Unable to create VLAN interfaces in ASA 5510
View 1 Replies
View Related
Apr 22, 2013
I have a mail archiver (hardware device) in my network that I need to access to from the Ipad/iphone. There is an app for it but I have to allow the access on the ASA. I created an 'object' for the device and added a Static NAT entry for it, then added an access rule. Its not working so I am guessing I did it wrong. The device uses port 8000 which I also added to the object. correct commands, or using the ASDM works too.
View 1 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Feb 5, 2012
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
View 2 Replies
View Related
Apr 17, 2011
I am setting up a new ASA 5510 on our inside network so that we can terminate our VPN connections on this ASA. I can get the VPN to work fine however I noticed that once I turned on my VPN profiles now when I try to access the ASDM I'm getting the VPN logon page. So I decided that in order to resolve this I need a separate interface dedicated to management of my ASA.
I'm trying to come up with the best way to do this. I've got two ports on the ASA plugged into my core switch. One is on a separate VLAN from the rest of my network traffic. This is the port I want to use for management. The second will be used to route all of my VPN traffic.
So far I haven't been able to get this to work at all. My thought was that it had to do with routes, NAT and ACLs. I've been playing with them but can't get any combination to work.
View 2 Replies
View Related
Jun 8, 2011
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
View 3 Replies
View Related
Apr 4, 2012
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
View 4 Replies
View Related
Jun 28, 2012
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
View 10 Replies
View Related
Jan 3, 2012
so i have a ASA 5510. The ASA is Connect with the Internet through PPOE DSL MODEM
The outside Interface get an IP. The Inside Interface get through DHCP from the ASA the Internet DNS SERVER (T-Online) But the HOST do not connect to the Internet because the DNS Server is timed out
Code...
View 10 Replies
View Related
