Cisco Firewall :: ASA 5510 - VPN Termination On Inside Network
Apr 17, 2011
I am setting up a new ASA 5510 on our inside network so that we can terminate our VPN connections on this ASA. I can get the VPN to work fine however I noticed that once I turned on my VPN profiles now when I try to access the ASDM I'm getting the VPN logon page. So I decided that in order to resolve this I need a separate interface dedicated to management of my ASA.
I'm trying to come up with the best way to do this. I've got two ports on the ASA plugged into my core switch. One is on a separate VLAN from the rest of my network traffic. This is the port I want to use for management. The second will be used to route all of my VPN traffic.
So far I haven't been able to get this to work at all. My thought was that it had to do with routes, NAT and ACLs. I've been playing with them but can't get any combination to work.
View 2 Replies
ADVERTISEMENT
Jan 2, 2012
So, I've set up Anyconnect client access to an ASA-5510.
I've got a handful of interfaces, which contain hosts that should be accesible to anyconnect clients. I'm unable to reach addresses on a specific network, due to what packet-tracer claims is an implicit deny, though I'm unsure where to apply an access-list in this case.
fw1# show nameif
Interface Name Security
Ethernet0/0.205 SECURE 90
[Code].....
View 7 Replies
View Related
May 9, 2011
I have deployed a read only domain controller in our DMZ as part of a domain-related project. That machine needs to be able to reach domain controllers on our internal network. To do so, it should traverse our ASA 5510, going from the DMZ Interface (security level set to 60) to the Inside Interface (security level set to 99).
I've created an ACL as following (alerting hostnames in the example):
access-list dmz_access_in extended permit ip host dmz.rodc.domain.local object-group int-domain-controllers
I've read in various spots that you have to create a NAT when traversing security levels, going from a less trusted interface (DMZ) to a more trusted one (internal.) Since this link will carry domain traffic, we do not want to create a real translation. Thus, I created a stand-in NAT that points to its own IP as follows:
static (dmz,inside) dmz.rodc.domain.local dmz.rodc.domain.local netmask 255.255.255.255
Long story short, the connection fails. I'm able to access other hosts in the DMZ and on another interface configured with the same security level (which I've explicitly allowed), but trying to go from the less-trusted DMZ to the more-trusted internal fails.
View 12 Replies
View Related
Mar 5, 2011
configure ASA 5510 as below
inside users should communicate with Hosts on the DMZ Zone and at the same time they should go for internet towards outside interface
ASA with 8.3(1)
default security levels
attached is the digram for your reference need communicate form inside to DMZ
View 1 Replies
View Related
Nov 18, 2011
One Host on inside network needs to access customized application hosted on Internet. Its a customized application run on port 80, 443, 5000-to-50020
How do I allow this host access for this specific application. I got ASA 5510 and host is in the inside network, we also got an ACL on inside interface to have control.
-Host IP on inside network - 172.16.30.15
-Application to access - 74.219.x.x
-Inside ACL name - inside-acl
View 5 Replies
View Related
Apr 22, 2013
I have a mail archiver (hardware device) in my network that I need to access to from the Ipad/iphone. There is an app for it but I have to allow the access on the ASA. I created an 'object' for the device and added a Static NAT entry for it, then added an access rule. Its not working so I am guessing I did it wrong. The device uses port 8000 which I also added to the object. correct commands, or using the ASDM works too.
View 1 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Feb 5, 2012
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
View 2 Replies
View Related
Oct 23, 2011
I have a Cisco ASA 5510 configured to access the internet, with an:
inside interface (ethernet 0/1) 130.130.0.254 and outside interface (ethernet 0/0) x.x.x.x
I have now configured another inside interface (ethernet0/2) on ASA with the IP 172.16.0.254 and I have connected it directly to another switch with a management IP 172.16.0.5.
The problem is that the two inside interfaces (130.130.0.254 &172.16.0.254) cannot communicate with each other thus the e0/2 172.16.0.254 interface cannot access the internet.
View 5 Replies
View Related
Jun 8, 2011
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
View 3 Replies
View Related
Apr 4, 2012
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
View 4 Replies
View Related
Jun 28, 2012
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
View 10 Replies
View Related
Jan 3, 2012
so i have a ASA 5510. The ASA is Connect with the Internet through PPOE DSL MODEM
The outside Interface get an IP. The Inside Interface get through DHCP from the ASA the Internet DNS SERVER (T-Online) But the HOST do not connect to the Internet because the DNS Server is timed out
Code...
View 10 Replies
View Related
Sep 11, 2012
I hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 Replies
View Related
May 22, 2011
This is an issue I'm currently exploring with TAC, but I'd like a quick reality check. We have a pair of ASA 5510s in Active/Standby stateful failover mode. In some tests failing over from the active to the standby system breaks SSH connections from hosts on our Inside to hosts on our DMZs.
A specific example is our backup server on Inside which is connecting to our mail server in the DMZ2, and running ssh/rsync/scp for the backups. A running backup job fails with network timeout errors when I trigger the failover. Also, sometimes the mail server loses or hangs on its connection to our LDAP server in DMZ1, although sometimes this connection is fine (DMZ2 is more "inside" than DMZ1, and I assume the LDAP look ups are many short connections, vs the rsync backup being one long connection).
TAC has suggested that open SSH sesions will always fail when the ASAs failover. I believe this is true for management connections to the ASA, but I don't see why it should be the case for an SSH session through the ASA to a server in the DMZ. TAC has suggested that I open some connections to servers in the DMZ and test what happens, and I can do so this Wednesday morning during a maintenance window.But, in general, is this true? That is, given an SSH session from a workstation to a server, should a failover break it? If so, why?
The setup is:
MyWorkStation-INSIDE -> CoreSwitch (vlan 10) -> [ ASA-INSIDE - - (ASA-internal-connection) - - ASA-DMZ ] -> CoreSwitch (vlan 3) -> TargetServer
That is, all our inside VLANs are routed by our core L2/3 switch to a VLAN that connects to the Primary and Secondary ASA's INSIDE ports. There are also seperate VLANS on the core for the ASA's DMZ1 and DMZ2 connections, which go to both ASAs and to any servers in these zones.
The description of the ASA Stateful failover [URL]says: "The state information passed to the standby unit includes these:
· The NAT translation table
· The TCP connection states
· The UDP connection states
· The ARP table
· The Layer 2 bridge table (when it runs in the transparent firewall mode)
· The HTTP connection states (if HTTP replication is enabled)
· The ISAKMP and IPSec SA table
· The GTP PDP connection database
[code]....
I'm not quite sure what the ISAKMP and IPSec SA tables do, but shouldn't an SSH connection through the ASA be just a TCP connection? "For us, SSH from Inside to hosts in the DMZ survives failover," or, "Yah, failover breaks all SSH sessions."
View 2 Replies
View Related
Dec 4, 2011
I have an ASA 5510 which i've configured for internet access.I can connect to the internet from the ASA box,I can ping public networks from the console of the ASA box,but cannot access public hosts from internal hosts connecting via the ASA box.Find my config below to know what i ahave omitted or committed.
[code]...
View 5 Replies
View Related
Dec 30, 2012
I have a Cisco ASA 5510 with 3 inside interfaces each connected to a 3750X switch port in a vlan. Outside interface is connected to external router with 209.155.x.x public IP. Static route exists for outbound traffic on outside interface.
3750X is configured for inter-vlan routing. VLANs 10, 20, and 30 have 172.16.x.1 IP address with static routes pointing to the each of the ASA inside interfaces - 172.16.x.254. Connected hosts are configured with gateways pointing to the appropriate vlan interface IP - 172.16.x.1.
Inter-vlan routing appears to be working - I can ping back and forth between hosts on different vlans, and I can ping each vlan IP.I can also ping each ASA inside interface from a host in the appropriate vlan, but I cannot ping internet sites (4.2.2.2 or 8.8.8.8) from hosts on the inside interfaces.
I can ping 4.2.2.2 from the ASA CLI. I can ping internal hosts on vlans 10,20,30 from the ASA CLI. But, no luck with pinging from inside host to internet hosts
View 12 Replies
View Related
May 19, 2011
I have recently deployed a Cisco ASA 5510 Security plus firewall on my companies network, but there is a problem that I am finding hard to get by and I think it is ASA related.
From (inside we are not able to hit any of our sites that are on the (outside). I have nat policies in place to translate the public to private, but I think I that I need some thing more. This seems to be occuring mainly with our external web sites as well as another animoly with regards to FTP (but it may be fixed if the http issue is resolved.)
I was hoping some with a lot more knowledge on ASA firewalls than my self can spot the error in my run-cfgs.
[code]....
View 15 Replies
View Related
Jan 10, 2013
I have seen many of these errors lately. We have just moved to a new office and I have basically only assigned a new IP to the outside interface.
[code]....
View 6 Replies
View Related
Jul 19, 2011
So I've run into a problem on my ASA5510, post-upgrade I can no longer connect to the inside interface from across our L2L VPN. I've tried both ASDM and SSH and the connections fail. I see in the logs that the attempt is being made, but it will eventually time out. There have been no problems with this type of connection with any previous upgrades, just this particular upgrade, I went from 8.4(1) to 8.4(2). I don't see much in the release notes or anything in a pre/post config diff that jumps out as a cause to this behavior. The only thing I did see in the release notes "CSCtg50770 Mngt-access (ASDM,SSH) to inside intf of 5580 fails over RA VPN session" which sounds like it could be my problem, but that was in the "Fixed in 8.4(2)" section and says it's for a 5580, maybe the fix for the 5580 broke it on a 5510??? I hope not and that I'm simply missing some new setting that I need to enable for this type of connection as this device is in a remote office.
View 2 Replies
View Related
Apr 5, 2012
We've had issues with our Exchange 2010 server (running on ESXi 4.1) since its default gateway was changed to our new ASA 5510. They manifested as frequent Outlook client connection dropouts or as IP address conflicts whenever Exchange was rebooted. The temporary fix was to disable the Exchange server NIC, bounce the ASA and enable the server's NIC again. We saw poor performance from Exchange after a while again, but after some research and testing I realised that disabling proxyarp on the inside interface fixed the problem permanently.
However I've now realised that the client VPN no longer routes properly because proxyarp is disabled on the inside interface, so I still have a problem.
View 10 Replies
View Related
Apr 16, 2012
I have an ASA 5510 which works great except I'm unable to connect to the remote access VPN from inside the network (behind the ASA). Is there a special NAT exemption required? [code]
View 6 Replies
View Related
Mar 8, 2011
I have setup two different subnet 192.168.1.0 and 192.168.2.0 on the same 'inside' interface. They are unable talking to each other. I can ping from firewall to both subnet. Both side unable talking to each other unless I add route on the both side systems.I have added the followings in ASA5510. [code]
View 8 Replies
View Related
Mar 3, 2013
I recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network. There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well. Internet setup was cake. The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks. I have one MPLS with AT&T and one MPLS with EarthLink. My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS. I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
Here's the topology I'm working with
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23
[Code].....
View 8 Replies
View Related
Feb 28, 2013
My internal network consists of Catalyst 3750 switches segmented into different VLANs. There is a default route on the layer 3 Catalyst switch sending all unknown traffice to the inside Internet of the ASA 5510. However, I'd like to have a separate VLAN for wifi guest access and send all of that traffic through one of the DMZ interfaces on the ASA 5510. I don't think you can have separate default routes based on VLANs on the 3750 switches so my only option is to make the ip address of the DMZ port the default gateway for all hosts on the wifi guest VLAN.
The problem I have is that I have a couple servers behind the inside interface that have services available to the public Internet via a NAT address on the outside interface. I want the guests on the wifi VLAN to have the ability to access the servers on the inside interface using the public address as well, but have not been able to come up with a solution yet.
Here is my config that pertains to this setup:
interface Ethernet0/0description Outside Interfacenameif Outsidesecurity-level 0ip address 76.47.10.x 255.255.255.224 rip send version 1rip receive version 1!interface Ethernet0/1description Inside Interfacenameif Insidesecurity-level 100ip address 192.168.17.1 255.255.255.0 rip send version 1rip receive version 1!interface Ethernet0/3description Wifi Guest Accessnameif DMZ2security-level 50ip address 192.168.60.1 255.255.255.0
global (Outside) 1 interface
nat (Inside) 0 access-list nonat
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (DMZ2) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
I've tried the following commands below but no dice.
same-security-traffic permit intra-interface
static (inside, inside) 76.47.10.x 192.168.17.88 netmask 255.255.255.255
View 3 Replies
View Related
Apr 19, 2012
I got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
View 3 Replies
View Related
Dec 11, 2012
I am working on pix 525, when connected through console I can access the whole internet but when i connect the pc to the inside interface i have no access to the internet. the pc can ping the pix inside interface and from pix i can ping the pc. My configuration is shown below.
PIX Version 7.2(2)
!
hostname pix
domain-name xyz.edu.pk
enable password xxxxxxxx encrypted
[code]....
View 8 Replies
View Related
Jan 27, 2013
I am trying to configure a server(192.168.5.50) in DMZ(192.168.5.0/24) to be able to communicate with a domain controller(10.5.44.220) in the inside network(10.5.44.0/24). I made some configuration using ASDM(not familiar with the CLI) but not working and it caused existing NAT not to work, for example RDP(TCP 3389) connection to 38.96.179.220
The things I am trying to achieve are
1. two way commucation between 192.168.5.50 in DMZ and 10.5.44.220 in Inside for SecureAuthPorts and SecureAuthOutbound service groups
2. NAT for 192.168.5.50 mapping 38.96.179.50 for the service groups mentioned above
3. NAT for other hosts already existing
View 2 Replies
View Related
Dec 18, 2010
I have 2 questions.Om my cisco 2811 (IOS 12.4(15) T9 IPBASE W/O Crypto) i am using 3 interfaces.And i have a pool of Global addresses: 200.x.z.97-200.x.z.126 255.255.255.0
FastEthernet 0/1 description WAN interfaceip nat outsideip address 200.x.y.253 255.255.255.0
GigabitInterface 0/2/0description DMZ interfaceip nat insideip address 10.0.0.1 255.255.255.0
GigabitInterface 0/3/0description LAN interfaceip nat insideip address 192.168.0.251 255.255.255.0
[Code]....
View 8 Replies
View Related
Jan 20, 2013
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies
View Related
Jun 13, 2012
I have an inside network using PAT to one outside address. Our DNS server is on another local, but outside address. I can't get the inside network to successfully get addresses.I have another inside address that just uses the wirewall and gets addresses just fine from the same server.I have the box checked in ASDN that enables DHCP on the inside interface and points to the correct DHCP server,PAT service is working properly if I use a hard coded address for a machine on the inside network.This is an ASA5540 with 8.3(2)
View 2 Replies
View Related
Nov 30, 2011
ASA 5505 and DMZ, I have a Base License.
What do I need to do for access inside network to DMZ?
I successfully configure, internet Access for DZM and inside network, web server can be accessed from internet, but I have problem to configure communication from inside network to DMZ.
View 14 Replies
View Related
Oct 16, 2012
I have a PIX 515E V7.0.4 and I'm having trouble with http access between the inside interface and a DMZ zone I have. I have a web server setup in the DMZ with an web interface to upload/download files. I can connect to this interface from a workstation in the inside network but when I try to download a file it is incredibly slow. If I upload a file there are no speed issues. If I connect using an https connection then both upload and downloads are at speeds I would expect.
I have disabled http inspect but this didn't improve the speed connection.
Other http communications from inside to outside do not have any speed issues in either direction.
View 34 Replies
View Related
