WAP200E access point that causes it to reboot after anything from 15 to 20 mins .I have run it off an injector and a POE switch, updated the f/w to WAP200E-ETSI-FW-2.0.3.0 and it still reboots itself .I have even been sent a new one from the supplier and it does the same thing.
View 5 RepliesCheck to see if there is a firmware upgrade and there is. Well I updated it with the newest and only one out there. I did the upgrade, said sucessful and now it will just random reboot or something........ every few minutes the power light starts flashing....... then all the light go out, then power flashes again and it comes back up. I have tried many times to reflash it with that new firmware but no avail. I wish I had the old firmware back because it was working fine till I did this upgrade.
View 5 Replies View RelatedMy new small router 866vae crashes and makes cold reboots every 20-30 minutes. I updated IOS, but it didn't work. The logs show texts like this:
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x808A0980z 0x808A4E90z 0x8089E2B4z 0x808AD350z 0x8086F000z 0x80A3B7A0z 0x80A1D444z
[Code].....
I am designing a cabling system to interconnect all the buildings in my school.In one of the building, I have 2 patch panels and switch to interconnect cables that comes into the building with cables that runs to the rooms.From what I understand, connectivity should be something like this:
1. Exterior cables coming in through the entry point.
2. Exterior cables terminates at the back of patch panel.
3. Patch cables run from the front of patch panel to a switch.
4. Patch cables run from the switch to another patch panel which connects the interior cabling that runs to the wall socket in each room.
My question:
1. Which ports should I use on the switch to interconnect exterior cable to the interior cable? They should be a connection between the exterior cabling and the interior cabling and both terminates in the same switch, but different ports. How do you allow communication to happen?
2. How do connect all the buildings to the router that connects to the internet?
how to power a WAP200E. In the datasheet it mentions it supports POE, however the customer does not have a POE switch and for one WAP220E is not willing to purchase.
What other options do we have? Is there a power supply for this AP?
directional antenna for the WAP200e.
I've been googling but can't seem to find a product. I have found omni-directional but no directional antennae
I want to know what is the maximum range of WAP200E. I found in an overview of the family of access points "CISCO SMB" that could reach up 4kms. Is that true?
View 3 Replies View RelatedI'm trying to bridge two buildings with two WAP200E. The connectivity is fine, but I'm only able to get one VLAN through the bridge. That is the default VLAN 1 wich is untagged. I have two additional VLANs wich is tagged. I can not get these two through the bridge. I have set up a single SSID, and enabled VLAN. I have also tried to set up more than one SSID, mapping each VLAN to separate SSID's, but bridging several SSID's between two AP's make the AP's loose connectivity periodically. What would be the propper way of bridging several VLANs between two WAP200E ?
View 1 Replies View RelatedI am having trouble with an pair of WAP200E's. The bridge between them stalls, found that one of the AP wireless LED don't show any activity. After powercycle the stalled AP, the bridge works again for a day or two. Have tried to replace the AP's still the same issue
Firmware is 1.20a
Just setup two WAP200E's, the bridge is "Connected" as I look Status > System Performance in both WAP's. However, I cannot get to the LAN from one network to the next. Cannot even ping the WAP's from either side.
I already have two WAP200E's on this network, that have been working well for month (164 day uptime), and they are configured with a wireless bridge between them, both networks on the same LAN (same 192.168.2.x network on either side). The bridge names are different, different from the main WiFi in the building, too (if it makes a difference), and the static IPs the WAPs have don't appear to have any conflicts on the network.
This is actually three buildings, one is the main one with a Cisco SR520 for a router, and a Cisco SF 200-24P switch. So two WAP200E's go into this switch now, and I see them both fine when going into the management interface. Then each of the other buildings has one WAP200E, and a small Netgear 8 port PoE gigabit switch at each building to power the WAP.
The Netgear switches aren't managed, and I've made sure any features like STP, VLANs, etc. are turned off. And the Cisco SF 200 switch is set at auto and all the defaults mostly, particularly for the ports. I tried doing a SmartPort for this latest WAP200E and that didn't change anything, tried disabling STP for it too, and no change. The PoE port for the working WAP200E is identical in config to the PoE port for the new WAP200E, and both show forwarding, all VLANs admitted (none are enabled, no VLAN tagging, etc.).
So now I am wondering if I can have two WAP200E's into one switch? Or two bridges on the same LAN subnet? Or is there something else I am missing or should configure?
I purchased a Linksys WAP200E Wireless-G Exterior Access Point – PoE and a HGA9N (9dBi) High Gain Omni-Directional Antenna through CDW Canada about three (3) years ago in April/2009. The first year it worked great and gave complete coverage throughout the Campground. The second year it started to become increasing less coverage and now in the third year, it has very poor coverage. I have purchased and installed a new Microcom HG2415U-PRO (15dBi) HyperGain Outdoor Omni Directional Antenna. This has NOT made any improvement so I am now thinking that the WAP200E Access Point is the faulty equipment. I have changed the channel to number 11 and still no improvement. The Signal Strength is only Good and then dropping to Fair and sometimes no signal at all. This is from a line of sight location that is only 60 yards (180 feet or 54.9 metres) away. There are no objects between the Antenna and the computer.
View 3 Replies View RelatedI have 3 WAP200e APs in a client site and I am having a problem with the signal between the APs and Motorola 9000 barcode scanners.The first one went in about 6 months ago and it worked fine. The client then asked for two more to be installed in a couple of rooms adjacent to the room where the first AP was installed. They use barcode scanners with these APs and since the two new ones were installed, the first on is dropping the connection to the scanner. I have turned the new APs off and everything is back to normal. I have reduced the power output of the two new APs and the situation has improved, but they still get problems, especially on Monday morning, where it won't work at all for the first few hours, and then bursts into life and works fine for the rest of the week.
View 7 Replies View RelatedIs it possible to connect two WAP200E on bridge mode without external antennas if they are 200 mts. (219 yard) apart?
View 2 Replies View Relatedi would like to know if wap200e will still have connection if there are trees in between. because we have 2 offices that is 200 meters apart and trees all over them. i just wanna know before we buy the unit.
View 1 Replies View RelatedI have a customer with a linux OS machine running Cisco Wireless Controll System.
He needs are to add a new wireless AP with the following features :
- compatible with most laptops
- exterior conditions "resistant" (sun, rain...)
- reasonnable performance (the AP would be a a roof with people on the roof itself, max distance : 15 meters, no walls)
I saw the WAP200E but I have no idea, if it is compatible with Cisco Wireless Control System
I have a problem to connect my WAP200E to SW2960. What is my mistake?Both are POE. I connect only Wap200e to SW2960 and I check the 15.4watts, but I suposed that WAP 200E doesn't respond, because WAP 200e doesn't turn on.I need to put to grown, or put some device before on connect to SW2960 to WAP 2000E.
View 10 Replies View RelatedBecause of a connection problem, I would like to know where I can see the clients associated to a WAP200E AP and the signal level of each client.
View 1 Replies View RelatedI'm using 4 wap200 cisco AP, 1 wap200e linksys AP and 1 cisco sf300-24p switch. Every AP has 2 SSIDs,one is for clients and one for mobile devices.I have updated the equipment to the latest firmware but I still encounter the same issue. The mobile devices go through APs and once every 2 days, my wap200e blocks its lan interface. I suspected a stp issue, because the switch was seeing MAC addresses coming from different ports.So I disabled STP on the switch and on the AP. The annoying thing thing is that none of my other antennas get cut off.I tried replacing it with a cisco wap200e,same issue.
View 1 Replies View RelatedI have an AIR-LAP1141-A-K9 it keeps rebooting itself. It seems to boot up and loads the flash and then shortly afterwards and before I get to console login it reboots.in reviewing what I've captured from the boot process is a message "Unexpected exception to CPUvector 200, PC = 1020" Below it is the following "Traceback - 0x1020 0x51351c 0x51351c 0x513c00 0x4FB1A8 0x4FB5B0 0x4F7FB8 0x191214 0x1912c8 0x57090 0x57398 0x1A5E50" I tried a couple google searches but didn't have any luck finding anything that matched what I have occuring.
View 5 Replies View RelatedI have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies View RelatedI have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
I got my new comcast connection and using CISCO DPC3008 cable modem and EA6500 Wifi Smart Router. Internet works fine and then suddently the internet goes away. Further investigation shows EA6500 Wifi router just reboots every few hours and then wifi devices don't reconnect like it used to do with previous routers.
View 6 Replies View RelatedI have an issue when I use Airplay through my iPhone4S, my router reboots after 30 secs or so. I have a WRT54G2 v1.5 and the receiver is a Pioneer VSX-1021-K.
However, when I used Airplay through itunes from my laptop, it works just fine. In addition, when I borrowed my neighbors router's(BELKIN) it was working fine also. So this lead me to believe that it's my router that is causing the issue.
i have issues with my 3 Cisco WAP200, they are rebooting after uptime from 9 to 20 days, i've tried to use latest firmware available 2.0.4.0 but it makes no differance to 2.0.2.4. I can't see logs to point out the problem (by SNMP i found only something like "out of swap space", and nothing by web interface).
View 3 Replies View RelatedI have a E2500 router that until recently has been working fine, the router currently will reboot at random occasions. I have tried resetting the router to factory defaults to test if the firmware was an issue but both the factory default and the most recent firmware build(1.0.05 build 2) offered on the download support page. I have tried 2 different AC adapters to test power and two different Cat5 cables so hard ware wise everything is looking good. I am concerned that it may be an issue still with firmware or with the cooling fan and the unit may be overheating.
View 1 Replies View RelatedSo I have a WRT160N firmware v3.0 wired connection to my PC, and at least once a day my connection speed drops from 2mbs down to almost dial up speeds at 60kps. Just unplugging the router then plugging it back in seems to fix it every time. I've contacted my service provider and they say there's no issue on their end, and since I don't get this problem when I plug the modem directly to the PC I agree with them. I've done a factory reset and that didn't work. I've gone through the FAQ and can't find anything useful in there.
View 7 Replies View RelatedNew E4200v2 router, latest 2.0.26 firmware. Reboots on its own <or> locks up and requires power recycle 3-4 times a day. More frequent if I attach a USB drive to USB port. Reset to factory, only using as a router (no USB drive, no printer sharing, no TimeMachine backups, etc.)Still locks up or reboots 3-4 times a day. I need a reliable router that does not reboot so often.
View 5 Replies View RelatedI have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.
Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none
are found.
Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.
Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?
<script id="overlay_tmpl" type="text/html">// <div id="<%= overlayId %>" class="_mp3rocket_overlay_style" style="left: <%= overlayLeft %>; top: <%= overlayTop %>; width: <%= overlayWidth %>; height: <%= overlayHeight %>"></div> // </script>
i have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
I upgraded my E3000 to a new E4200 several months ago. I use an SSL VPN to connect to work which worked fine on 1.0.01 and 1.0.02 but I upgraded to 1.0.03 to fix an issue where the router constantly reboots when I stream Netflix or Hulu and now the router reboots with Netflix, Hulu AND the SSL VPN tunnel initiation.
View 6 Replies View RelatedI've just confirmed that everytime I try to stream music from my MacBook Pro (iTunes) that is connected to my WiFi network using the 5GHz mode (channel width is Auto, channel: Auto (DFS)) to a couple Airport Express cubes are connected via the 2.4 GHz WiFi (channel width: Auto, channel: 10) the E4200 router reboots. When I set the MBP to use the 2.4 GHz mode I can stream music without causing the E4200 to reboot. The E4200 is running firmware 1.0.03.
View 9 Replies View RelatedWatch youtube? Router resets! Hookup a wired connection? REBOOT! Hookup a tivo wirelessly, use wifi calling, or listen to spotify.. REBOOT!Is there ANY way for this router to NOT reboot randomly?
View 4 Replies View RelatedMy WRT310n router, since yesterday, stopped working "normally".It was disconnected from the power plug in order to put it in another shelve and when I plugged it in, voilá, constant reboot.I keeps rebooting forever... I can't even make an ethernet connection. Reboot, after reboot. Tryied to make a reset with no luck, 5 seconds reset, 30s reset, pressing reset while plugging it in.Even with nothing connected to it (neither wireless nor lan), just the power plug and it keeps re booking one after another.
View 2 Replies View Related