Cisco Wireless :: WAP200E Access Point Drops Connections
Aug 18, 2012
I purchased a Linksys WAP200E Wireless-G Exterior Access Point – PoE and a HGA9N (9dBi) High Gain Omni-Directional Antenna through CDW Canada about three (3) years ago in April/2009. The first year it worked great and gave complete coverage throughout the Campground. The second year it started to become increasing less coverage and now in the third year, it has very poor coverage. I have purchased and installed a new Microcom HG2415U-PRO (15dBi) HyperGain Outdoor Omni Directional Antenna. This has NOT made any improvement so I am now thinking that the WAP200E Access Point is the faulty equipment. I have changed the channel to number 11 and still no improvement. The Signal Strength is only Good and then dropping to Fair and sometimes no signal at all. This is from a line of sight location that is only 60 yards (180 feet or 54.9 metres) away. There are no objects between the Antenna and the computer.
View 3 Replies
ADVERTISEMENT
Nov 7, 2011
Because of a connection problem, I would like to know where I can see the clients associated to a WAP200E AP and the signal level of each client.
View 1 Replies
View Related
Jun 21, 2012
I'm using 4 wap200 cisco AP, 1 wap200e linksys AP and 1 cisco sf300-24p switch. Every AP has 2 SSIDs,one is for clients and one for mobile devices.I have updated the equipment to the latest firmware but I still encounter the same issue. The mobile devices go through APs and once every 2 days, my wap200e blocks its lan interface. I suspected a stp issue, because the switch was seeing MAC addresses coming from different ports.So I disabled STP on the switch and on the AP. The annoying thing thing is that none of my other antennas get cut off.I tried replacing it with a cisco wap200e,same issue.
View 1 Replies
View Related
Nov 25, 2012
I am running the e3000 as an access point.. My iphone and ipad connect to it seamlessly. After a few hours to days, they are no longer recognized by the router. Nothing I reset on the phone or ipad makes any difference. The only solution I have found is to re-boot the router. They then re-connect on their own.
View 4 Replies
View Related
Apr 16, 2007
What is the maximum number concurrent wireless connections that a WAP54g v3 can have?
View 9 Replies
View Related
Mar 3, 2013
I am having an issue with the mentioned AP, it does not accept new user connections, however new user can connect after the AP is restarted.I would like to know if there is a limit on the number of wifi users for linksys x2000?
View 1 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
May 26, 2011
I have a 2wire 2701hg-b wireless router/DSL modem. Every once in awhile, my wireless devices all lose their connection to the router at the same time. I believe the problem is internal to the router/modem as all my wireless devices' connections are dropped at the same time AND I can only get them connected once I disable and then re-enable the wireless on the router. The problem seems to only affect wireless devices as all my wired devices remain connected and my Internet connection remains intact as well.
View 1 Replies
View Related
Feb 27, 2013
How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies
View Related
Aug 26, 2012
I recently bought a refurbished E1000 wireless router from Amazon, and from the first day I've had recurring connection issues with it. Every half hour or so it will lose all of its connections (wireless and ethernet) and requires a hard reset. After resetting, all connections are good for a little while but then the problem occurs again. When plugged directly into my modem (Motorola SB6121), my internet access is completely fine.
The router has the latest firmware as far as I know (2.1.02 build 5 May 6, 2011), and I've tried to change several settings (MTU to 1400, Fragmentation Threshold to 2306, etc) but to no avail.
View 4 Replies
View Related
Sep 5, 2011
My E4200 seems to be dropping connections throughout the day. For wireless it'll still show full signal and connection, but there will be no internet activity for about a minute. Then after a minute things will work just fine again. For wired I notice it in my XBox mainly when I get dropped from games as constant as the wireless drops.I believe my modem isn't the problem since the old router never dropped connections on the hard wired devices. Occasionally my old D-Link router would drop wireless, but never this frequent,I am running 1.0.02. I've rebooted the router/modem several times. I even reinstalled the entire setup with the current version of Cisco Connect as the tech person suggested, but still no luck. The first week or so using this router was flawless, but ever since then it's been dropping connections several times throughout the day to any device connected (wireless or wired). The problem seems that the router just hiccups the connection very quickly, so quickly that Windows doesn't even recognize the connection has been lost, but long enough to drop a multiplayer game on XBox or to have me mashing refresh on my internet browsers.
View 2 Replies
View Related
Apr 20, 2012
I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies
View Related
Jun 5, 2012
I have a E3200 and upgraded the firmware last weekend to 1.0.0.4 and now I get dropped connections every few minutes. I was working form home and VPN into a west coast client and was getting dosconnected every few minutes so I thought it was possibly their VPN but when I checked my outloook it was also disconnected and is not associated with their VPN. I called Comcast and they said the modem has been online for 19 days so now everything points to the router.
View 5 Replies
View Related
Jun 29, 2012
Router is connected to my ISP with the option Keep alive and redial value of 20 seconds (the lowest i can set). There are two distinct problems: Router drops connections at random intervals. It can happen once a day or several times a day. It always happens overnight (so every morning it isn't connected). This doesn't seem to be related to ISP as direct connection to computer is stable.The Keep alive option isn't working. When it drops connection it isn't trying to re-eastablish it for at least 2 minutes (the longest i have waited so far, 6 times the redial value configured). Producing external traffic (e.g. constant pinging of some host by IP address, refreshing some web page) doesn't work. When i log on to admin console (browser based) simply clicking connect button brings connection back online. I've even been looking at status page constantly refreshing to see if it ever made a single attempt and it appears it didn't.I did my "homework" before posting (upgraded FW to 2.0.02 build 3, finetuned MTU).
View 2 Replies
View Related
Sep 2, 2011
The router works fine until I plug the 4th wire in the back, which goes to a 2nd desktop computer, then it is only a matter of time until the router drops all internet connections including the direct wire to desktop #1, wireless, and the other two wires.This is my 2nd e2000 router since Amazon replaced the first one after about 4 months as it was having the same problem.
View 5 Replies
View Related
Mar 31, 2013
Region : Argentina
Model : TL-WR741ND
Hardware Version : V4
Firmware Version : 3.16.4 Build 130205 Rel.63090n
ISP : Fibertel
My TL-WR741ND is about 1 year and a half old, it was working fine until about 2 weeks ago. I need to reset it, times between resets is not consistent, meaning, it can take 30 minutes, or 8 hours, but it needs to be reset. Right now, there are 2 wired connections (PS3 and Desktop PC) and 7 wireless (4 cell phones, 2 notebooks and 1 netbook). 1 of the notebooks has static IP, and it also has a VM running, with another static IP. Also some port forwarding simply stopped working (ports 80 and 1180), the rest of the ports work flawlessly, but trying to forward the port 80 and 1180 (to the 2 static ips) won't work. I already upgraded the firmware, and the problem persists, also changed the channel (from 6 to 1, and then from 1 to 11).
Installing dd-wrt/openwrt/gargoyle or anything like that, is not an option. The only reason why I bough t this router, was because I could use dd-wrt, I installed it 1 year and a half ago, and it simply sucked, the wireless bandwidth was non existent, and it was a headache. I installed it again last week, to see if it could be a solution, and I was not even able to save changes in the control panel. I need a real solution, and installing a firmware that works only on chrome is not an option (specially when I use Firefox, and I needed to install chromium just to erase dd-wrt)
View 2 Replies
View Related
Dec 12, 2012
My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit. My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. Will this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit.
View 1 Replies
View Related
Mar 6, 2013
I have a WRT54GL that I bought about 2 months ago, and I've had nothing but problems with the wi-fi since I started using it. It works as normal about 90% of the time, but usually 50+ times per day, I won't be able to connect to the router wirelessly (with ANY device, no matter how close I am to the router) for 1 to 2 minutes. The fact that I can't connect to the router with ANY devices during these times leads me to believe that the problem lies with the router itself. Another thing to note is that the wired connection to the router works just fine during these wireless outages.
I've tried changing channels and upgrading the firmware, but nothing has changed. Did I just get a bad router?
View 7 Replies
View Related
Apr 18, 2011
I just recently purchased a Cisco ASA 5505 ASA ver 8.2. I run a teamspeak server/ssh/dns and domain on the same server on the network. Before I switched to the asa, I have a regular DGL-4100 that ran with no issues. I have noticed that the connections are very unstable and disconnect frequently and when they do they take 1 to 5 minutes to be able to reconnect. I have done some cisco IOS but am fairly new to this. [code]
View 4 Replies
View Related
Nov 1, 2012
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Jun 6, 2011
how to power a WAP200E. In the datasheet it mentions it supports POE, however the customer does not have a POE switch and for one WAP220E is not willing to purchase.
What other options do we have? Is there a power supply for this AP?
View 4 Replies
View Related
Jan 15, 2013
directional antenna for the WAP200e.
I've been googling but can't seem to find a product. I have found omni-directional but no directional antennae
View 2 Replies
View Related
Sep 9, 2012
I want to know what is the maximum range of WAP200E. I found in an overview of the family of access points "CISCO SMB" that could reach up 4kms. Is that true?
View 3 Replies
View Related
Sep 17, 2010
I'm trying to bridge two buildings with two WAP200E. The connectivity is fine, but I'm only able to get one VLAN through the bridge. That is the default VLAN 1 wich is untagged. I have two additional VLANs wich is tagged. I can not get these two through the bridge. I have set up a single SSID, and enabled VLAN. I have also tried to set up more than one SSID, mapping each VLAN to separate SSID's, but bridging several SSID's between two AP's make the AP's loose connectivity periodically. What would be the propper way of bridging several VLANs between two WAP200E ?
View 1 Replies
View Related
Mar 1, 2009
I am having trouble with an pair of WAP200E's. The bridge between them stalls, found that one of the AP wireless LED don't show any activity. After powercycle the stalled AP, the bridge works again for a day or two. Have tried to replace the AP's still the same issue
Firmware is 1.20a
View 15 Replies
View Related
Jan 9, 2012
My 655 router (RevB, Firmware 2.03) is connected from one side to a DSL modem and on the side to two wired PC's and via wi-fi to several other wireless clients (two smart phones and two notebooks). All is well until I try to connect a specific notebook. Connection is estabished for about 30sec and then the router drops ALL connections (including internet and local network!) and I must re-start him by un-plugging from power. This phenomena is specific to a specific notebook since with the other one
View 7 Replies
View Related
Jul 9, 2006
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies
View Related
Jan 17, 2013
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies
View Related
Dec 14, 2011
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies
View Related
Jul 3, 2012
I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
Apr 19, 2012
Just setup two WAP200E's, the bridge is "Connected" as I look Status > System Performance in both WAP's. However, I cannot get to the LAN from one network to the next. Cannot even ping the WAP's from either side.
I already have two WAP200E's on this network, that have been working well for month (164 day uptime), and they are configured with a wireless bridge between them, both networks on the same LAN (same 192.168.2.x network on either side). The bridge names are different, different from the main WiFi in the building, too (if it makes a difference), and the static IPs the WAPs have don't appear to have any conflicts on the network.
This is actually three buildings, one is the main one with a Cisco SR520 for a router, and a Cisco SF 200-24P switch. So two WAP200E's go into this switch now, and I see them both fine when going into the management interface. Then each of the other buildings has one WAP200E, and a small Netgear 8 port PoE gigabit switch at each building to power the WAP.
The Netgear switches aren't managed, and I've made sure any features like STP, VLANs, etc. are turned off. And the Cisco SF 200 switch is set at auto and all the defaults mostly, particularly for the ports. I tried doing a SmartPort for this latest WAP200E and that didn't change anything, tried disabling STP for it too, and no change. The PoE port for the working WAP200E is identical in config to the PoE port for the new WAP200E, and both show forwarding, all VLANs admitted (none are enabled, no VLAN tagging, etc.).
So now I am wondering if I can have two WAP200E's into one switch? Or two bridges on the same LAN subnet? Or is there something else I am missing or should configure?
View 1 Replies
View Related
