I have a 2wire 2701hg-b wireless router/DSL modem. Every once in awhile, my wireless devices all lose their connection to the router at the same time. I believe the problem is internal to the router/modem as all my wireless devices' connections are dropped at the same time AND I can only get them connected once I disable and then re-enable the wireless on the router. The problem seems to only affect wireless devices as all my wired devices remain connected and my Internet connection remains intact as well.
My linksys wireless router bit the dust, trying to resurrect this old modem for use as a wireless router only. I've got the 2wire 2701hg-d connected to my isp's cable modem and to my laptop via two of the LAN ports. the lac connection gives me internet access (obviously...here i am...) but the wireless connection gives me no internet access...i can log in to the 2wire's firmware via the wireless connection...but i' m not sure what settings (if needed) i have to change.
I am switching from Qwest to another ISP that has provided me with a modem that is not set up with an internal wireless router. I've been told that I can configure the 2wire 270hg-d to use it as a wireless router that can then be connected to the ISP modem. Need proper configuration settings on the 2wire..
I'm using a 2wire 2701HG-B wireless router/dsl modem combo. My computer is a Win 7 Ultimate 64bit. The router/modem has been reliable for the last 2 years.. hardly ever needing a reset, reboot, or anything. Then all of a sudden my wifi network didn't show up anymore. I did a reboot, nothing. Kind of weird so I got on the phone with AT&T and they walked me through some simple stuff and they determined it's either the router or my computer. Well I know it's not the computer, I can use the mobile hotspot on my android phone and it gets on just fine.All of the lights on the router are green, AT&T showed that all the tests show the internet connection is working. Since the router is not sending out a wifi signal anymore, I had to plug the ethernet cable in. The system recognizes a connection but says it isn't connected because it is a "public" connection. Additionally, if I go to network connections with the cable plugged in, I can see my DirecTV DVR is showing on the network (because it is connected to the router via ethernet too). So it isn't broadcasting wifi, I can see my DVR over the network in windows, but I can't get the IP renewed.
When I try to do an ipconfig /renew, it says this:Windows IP Configuration An error occurred while renewing interface Local Area Connection : The operation was canceled by the user.An error occurred while releasing interface Loopback Pseudo-Interface 1 : The system cannot find the file specified.The AT&T rep said I may need a new modem and router. It seems weird because it worked fine one night, then the next night all of a sudden it didn't work.
A 2 Wire 2701HG-B DSL MODEM/Router Upstairs Wired into 2 PCs upstairs WiFi to a PC Downstairs.
I killed the DSL service and got U-verse, but that added a new Modem/WiFi downstairs. I still have the 2Wire upstairs, but it has no phone connection.Can I use the 2Wire to "Receive" and "distribute" the WiFi signal from downstairs?
I don't see how to turn off the DSL MODEM. If I put in the ID and Password for the WiFi router downstairs into the 2Wire upstairs, will it "Login" or will it conflict? Are there special settings for the PCs to access the U-Verse router through the 2Wire?Basically, I want to know if the upstairs 2Wire can receive the U-verse signal and convert it to wired signal for the 2 upstairs PCs.
I can't connect wirelessly or hardwired. My internet provider is AT&T DSL. My router is a 2Wire 2701HG-B and my antivirus and firewall is McAfee. Attached are the ipconfig/all and Xirrus Wifi.
I purchaseda trendnet 692 GR router because I understood that I would be able to stream from let's say my computer to my TV that is up the stairs. Here is the problem. I did get the router to use my existing 2Wire 2701HG modem.Yes I can connect my Samsung 6100 to the wireless 2Wire but I thought the trendnet setup would work the best.I and Trendnet support set up my router and media bridge and the two do work but my tv won't work through the MB. I have connected to the network but the next part of the connection (the internet) won't connect. I have tried different IP settings that I thought would connect but nothing so far has worked.Also I have taken a 50' ethernet cablefrom the trendnet router to the tv and I do get a connection.I have also taken a laptop through the media bridge and connected to the trendnet router.The customer service at trendnet can't take this to the next level(which is a$40 one session professional service)
Everyone's 2wire works in bridge mode of they follow these steps url...but when i try i get no internet connection nor does it pick up any internet activity. I even input my account and dsl password in the netgear router gateway still no luck.I'm trying to use the netgear router because in my room i only get 2 signals bars and if i switch to the netgear wireless N router the signal strength would be alot better.
I recently bought a refurbished E1000 wireless router from Amazon, and from the first day I've had recurring connection issues with it. Every half hour or so it will lose all of its connections (wireless and ethernet) and requires a hard reset. After resetting, all connections are good for a little while but then the problem occurs again. When plugged directly into my modem (Motorola SB6121), my internet access is completely fine.
The router has the latest firmware as far as I know (2.1.02 build 5 May 6, 2011), and I've tried to change several settings (MTU to 1400, Fragmentation Threshold to 2306, etc) but to no avail.
My E4200 seems to be dropping connections throughout the day. For wireless it'll still show full signal and connection, but there will be no internet activity for about a minute. Then after a minute things will work just fine again. For wired I notice it in my XBox mainly when I get dropped from games as constant as the wireless drops.I believe my modem isn't the problem since the old router never dropped connections on the hard wired devices. Occasionally my old D-Link router would drop wireless, but never this frequent,I am running 1.0.02. I've rebooted the router/modem several times. I even reinstalled the entire setup with the current version of Cisco Connect as the tech person suggested, but still no luck. The first week or so using this router was flawless, but ever since then it's been dropping connections several times throughout the day to any device connected (wireless or wired). The problem seems that the router just hiccups the connection very quickly, so quickly that Windows doesn't even recognize the connection has been lost, but long enough to drop a multiplayer game on XBox or to have me mashing refresh on my internet browsers.
I purchased a Linksys WAP200E Wireless-G Exterior Access Point – PoE and a HGA9N (9dBi) High Gain Omni-Directional Antenna through CDW Canada about three (3) years ago in April/2009. The first year it worked great and gave complete coverage throughout the Campground. The second year it started to become increasing less coverage and now in the third year, it has very poor coverage. I have purchased and installed a new Microcom HG2415U-PRO (15dBi) HyperGain Outdoor Omni Directional Antenna. This has NOT made any improvement so I am now thinking that the WAP200E Access Point is the faulty equipment. I have changed the channel to number 11 and still no improvement. The Signal Strength is only Good and then dropping to Fair and sometimes no signal at all. This is from a line of sight location that is only 60 yards (180 feet or 54.9 metres) away. There are no objects between the Antenna and the computer.
I have a E3200 and upgraded the firmware last weekend to 1.0.0.4 and now I get dropped connections every few minutes. I was working form home and VPN into a west coast client and was getting dosconnected every few minutes so I thought it was possibly their VPN but when I checked my outloook it was also disconnected and is not associated with their VPN. I called Comcast and they said the modem has been online for 19 days so now everything points to the router.
Router is connected to my ISP with the option Keep alive and redial value of 20 seconds (the lowest i can set). There are two distinct problems: Router drops connections at random intervals. It can happen once a day or several times a day. It always happens overnight (so every morning it isn't connected). This doesn't seem to be related to ISP as direct connection to computer is stable.The Keep alive option isn't working. When it drops connection it isn't trying to re-eastablish it for at least 2 minutes (the longest i have waited so far, 6 times the redial value configured). Producing external traffic (e.g. constant pinging of some host by IP address, refreshing some web page) doesn't work. When i log on to admin console (browser based) simply clicking connect button brings connection back online. I've even been looking at status page constantly refreshing to see if it ever made a single attempt and it appears it didn't.I did my "homework" before posting (upgraded FW to 2.0.02 build 3, finetuned MTU).
The router works fine until I plug the 4th wire in the back, which goes to a 2nd desktop computer, then it is only a matter of time until the router drops all internet connections including the direct wire to desktop #1, wireless, and the other two wires.This is my 2nd e2000 router since Amazon replaced the first one after about 4 months as it was having the same problem.
Region : Argentina Model : TL-WR741ND Hardware Version : V4 Firmware Version : 3.16.4 Build 130205 Rel.63090n ISP : Fibertel
My TL-WR741ND is about 1 year and a half old, it was working fine until about 2 weeks ago. I need to reset it, times between resets is not consistent, meaning, it can take 30 minutes, or 8 hours, but it needs to be reset. Right now, there are 2 wired connections (PS3 and Desktop PC) and 7 wireless (4 cell phones, 2 notebooks and 1 netbook). 1 of the notebooks has static IP, and it also has a VM running, with another static IP. Also some port forwarding simply stopped working (ports 80 and 1180), the rest of the ports work flawlessly, but trying to forward the port 80 and 1180 (to the 2 static ips) won't work. I already upgraded the firmware, and the problem persists, also changed the channel (from 6 to 1, and then from 1 to 11).
Installing dd-wrt/openwrt/gargoyle or anything like that, is not an option. The only reason why I bough t this router, was because I could use dd-wrt, I installed it 1 year and a half ago, and it simply sucked, the wireless bandwidth was non existent, and it was a headache. I installed it again last week, to see if it could be a solution, and I was not even able to save changes in the control panel. I need a real solution, and installing a firmware that works only on chrome is not an option (specially when I use Firefox, and I needed to install chromium just to erase dd-wrt)
I have a WRT54GL that I bought about 2 months ago, and I've had nothing but problems with the wi-fi since I started using it. It works as normal about 90% of the time, but usually 50+ times per day, I won't be able to connect to the router wirelessly (with ANY device, no matter how close I am to the router) for 1 to 2 minutes. The fact that I can't connect to the router with ANY devices during these times leads me to believe that the problem lies with the router itself. Another thing to note is that the wired connection to the router works just fine during these wireless outages.
I've tried changing channels and upgrading the firmware, but nothing has changed. Did I just get a bad router?
My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit. My sd2008 switch keeps dropping the connection. If I replace the sd2008 with another switch it works without an issue. Will this switch has a limited lifetime warrenty. If true, can I return this switch for a replacement? The switch has firmware version 2.1 and the serial number is really hard to make out on the bottom of the unit.
I have a 2Wire 2701HG-B modem/router provided to me by AT&T for my DSL service. I have one issue and a seperate question sort of related to it.The issue I'm having is that whenever a laptop gets online with wireless internet the modem will randomly reset connection.Some times it will do it every 30 seconds, some times it will be once an hour or even more.It works perfectly fine on any laptop when plugged in with Ethernet cable but only with wireless it will glitch out. It does this whether it is the only computer online on the network, and also when there are a few others online so it's just the simple fact of the wireless resetting it somehow.I've done lots of google searching and some people say changing the line pair settings fixed it for them. Some say changing from b/g mode to just g mode fixed it. I've tried every thing that I've come across and nothing has worked so far. Apparently this is a very common problem for this model I just can not find the right solution that has worked for other people, to work for me as well.
if I were to want to make this modem/router just a modem and hook up my own router for N wireless would this be possible? I know I've read ways about putting combos in DMZ mode or something but I don't really know what I'm looking for because everything is worded different in this modem's settings.Can any one provide any insight as to if this is possible, and if it's even worth it to do so? Mainly worried about the first thing I mentioned though, this is just a side note.
I just recently purchased a Cisco ASA 5505 ASA ver 8.2. I run a teamspeak server/ssh/dns and domain on the same server on the network. Before I switched to the asa, I have a regular DGL-4100 that ran with no issues. I have noticed that the connections are very unstable and disconnect frequently and when they do they take 1 to 5 minutes to be able to reconnect. I have done some cisco IOS but am fairly new to this. [code]
Just got a never used AT+T Wireless Router (2701HG-B Gateway) from a friend to use with my laptop and comcast broadband connection. I have windows vista, and use IE as my main browser. Can I used, or is it set up to only work with an AT+T connection? I do have all the software discs that came with the unit, but haven't run them as they seem mainly for setting up DSL connection with AT+T.
My 655 router (RevB, Firmware 2.03) is connected from one side to a DSL modem and on the side to two wired PC's and via wi-fi to several other wireless clients (two smart phones and two notebooks). All is well until I try to connect a specific notebook. Connection is estabished for about 30sec and then the router drops ALL connections (including internet and local network!) and I must re-start him by un-plugging from power. This phenomena is specific to a specific notebook since with the other one
I can connect wired but not wirelessly. I get limited or no connectivity. When I try to repair I get the message "cannot connect to dhcp server. request has timed out"
I want a ipad 2 and I have 2wire 2700HGB. It needs a phone jack, yet it is suppose to be wirless. What do need to do. We have our home protection system in the kitchen in it's phone jack.I am so confused! Can I have a wireless connection and a home phone line together?
I have a dell desktop with win xp i need to activate but cant get online to do so. The dsl and internet lights are on and my nic light is on via the ethernet cable.I went into safe mode to do a ipconfig and i got a internal error request not supported message. I wanted to try configuring the network connection settings but when i clicked on that in control panel when i was in safe mode nothing came up.
I have a network that starts with a Linksys wireless router (DSL connected here) then it goes to a Netgear switch (computers connected here) and then a Netgear wireless router for an iMAC to connect to. I can't see the last router or the iMAC on my Win 7 machine? when I map network I get an error message about an incompatible device.
I have AT&T 2wire wireless modem. I am working on a friend's computer and his computer detects the modem but won't connect. I have entered the 10 digit number on the router into his laptop and then I tried the homegroup password and still it won't connect.
I have at&t DSL.I NEEDED to upgrade my wireless gateway from the 2wire wireless-G gate way that I had.I also have a Netgear WNDR-4000 750N Wireless Dual Band Router.
I know I needed an at&t modem to run my DSL, so I purchased (before reading reviews) a Netgear 7550 Wireless Gateway from at&t (they did not have any "N" single user modems (if there is such a thing).I have read through other posts that it is possible to connect the two and I would not need the 7550 for anything else but a modem (disabling broadcast).
The question is ... do I REALY need to do all this or can I just get away with the 7550?Or will the Netgear WNDR-4000 750N Wireless Dual Band Router, if installed and used, fix some of the issues that other 7550 users have said in other posts?
Wireless ... I have 3 gaming systems, two PC's, a tablet and 4 smartphones.I will be using 3 wired ports ... 1 gaming system, PC, and a blue-ray.
And yes, my 2wire wireless-g gateway ran all these ... not efficiently or reliably, but they all did run.
I have not received the Netgear 7550 yet, just trying to get some opinions on which setup would be better.
I currently have Comcast as my ISP.However there are only 4 wired ports on the router and I need an additional 2 ports for my needs. I have a 2wire 38000HGV-B Uverse Wireless gateway. I wanted to know if I could use one of the output ports from the Comcast wireless gateway and feed the 2wire Gateway to achieve the additional ports that I need. Also the wireless router from comcast is so difficult to setup that I don't even use the wireless. The 2wire gateway is much easier to setup and use and I could have wireless available where I don't have it right now.
I've got a Gateway 2wire 3800 HGV-B router which works fine wirelessly, but when using an ethernet cable to connect to the internet, it doesn't even recognize the computer. My laptop runs wirelessly all the time, and I recently picked up a desktop PC for home here, and it's the first wired connection I'm using, but for some reason the wired connection isn't connecting to my network, but instead it's own Unidentified Network.
I have a 2wire Modem connected to a Cisco Wireless N Router, that is connected to another Cisco Wireless N Router. All was working well. In my absence sbc (AT&T) changed the pass word of the 2wire Modem. The 2wire has stoped communication with the Cisco Wireless N Routers. I connected am Ethernet wire to one of the ports of the 2wire, and connected it to the 2nd Cisco Wireless N Router. The signal gets to the 2nd Cisco Router. However, when I attempt to access the Internet on the CPU connected to the 2 Cisco Router, I get an error Message saying that there is a problem with the Modem and/or Router. On the available Networks selection screen I can see the connections that I want. The selection info shows connected. But when I try to connect, the I can't.
I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
