i have issues with my 3 Cisco WAP200, they are rebooting after uptime from 9 to 20 days, i've tried to use latest firmware available 2.0.4.0 but it makes no differance to 2.0.2.4. I can't see logs to point out the problem (by SNMP i found only something like "out of swap space", and nothing by web interface).
View 3 RepliesI purchased 3 of these Wireless-G access points and none of them are plug and play. I am here because I have spent the last three hours trying to go through every step they suggest in the Quick Start Guide.
I tried entering in a web browser the default IP address and wait for a login that does not appear.
I have a wap200 with a static ipaddress e.g. 192.168.249.205/24 (it is for management and is in vlan 1). Firmware of the wap is 2.0.4.0. No gw and no dns. (they are not necessary) I export the config . I have a second wap200 and import the config.bin to the new wap. ThenI like to change the static address and the name of the new wap, but - and this is the problem - it asks me to fill out the dns (the address for primary dns cannot be 0 and 255), but I absolutely don't want that because there is no dns or gw (management only). And if I fill it out I cannot go the the internet with the wap.
So I also have some other wap200 where I could import the config.bin and change the static ip without giving a dns (firmware 2.0.1.0). can I go back to a previous firmware (Europe) and where can I find it. Looked for it, but seeing only the last one 2.0.4.0 etsi.Or is there another method to skip the dns with a static ipaddress?
I do have problems with remote management of a Wireless Accespoint WAP200.The WAP200 is connected to a router RVS4000 and works well..There are several nodes in the LAN, all static IP, all forwarded in the RVS4000..All nodes can be managed in the LAN as well as from outside..Exept the WAP200, from inside in LAN no problem, but from outside gives a 404 return.I build other similar LAN's, but the same, no connection.
View 8 Replies View RelatedI have a Cisco WAP200 Wireless-G Access Point - PoE/Rangebooster with the latest firmware 2.0.2.4-ETSI?I’m trying to set it up as a repeater, repeating the wireless signal from a Cisco 877W.I have configured the WAP200 with the same SSID, WPA key, and channel as the 877W.
I have changed the WAP200’s AP Mode setting to Repeater, and picked up the 877W’s MAC Address.The WAP200 is broadcasting and I can connect to the wireless network, but I don’t get DHCP. It’s almost like it’s still in Access Point mode.
I'm trying to setup a WAP200 as a wireless repeater and I am having some problems. The SSID I am trying to bridge is coming from a WRV210.
I on both devices I have the SSID, security, and channel set the same. The WAP200 is set to Repeater mode and I did a site survey to find the WRV210. The WRV210 is set to to allow the WAP200 repeat its signa using auto select, manual with site survey and manual actually entering the MAC address by hand.
Nothing seems to work. I can see the wireless next work but when i connect to the repeater I never get an IP address.
Network set up; wireless router (D-link DIR825) to Cisco switch (SD208p) and have Wap200 hooked to cisco switch to extend range up one floor. Can see it as wireless network, but cannot configure it with web browser. Address 192.168.1.245 just times out via pings as well. Have done all resets, power on reset, etc nothing.
View 3 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.
Should I be adding the additional MACs there?Does the WAP200 even support multiple VLAN/SSID?
Network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
is any way to get information about clients connected to an AP WAP200?
View 2 Replies View RelatedWhich AP's Wap200 can bridge with this ?
View 1 Replies View RelatedI have 3 WAP200 wireless-G access points. I have one set up as an AP the other two are set up as repeaters to the main AP.
My question is Do I need a lan connection to each repeater ?
also, do I need to create SSIDs for all three? & if so, do they need to be the same?
I have a Linksys WAP200 Wireless-G Access Point problem. It is SW version 2.0.4.0. I have it configured for a small network and the problem seems to be that it is not forwarding DHCP requests onto my DHCP server. I know that it is not a SSID or Key issue as when I give my devices static IP addresses, they communicate fine within my system. The only issue seems to be when the devices make DHCP client requests. I also know that the problem is not my DHCP server as it has the device's IP / mac addresses in its configuration file and other wired devices are able to communicate with it to get their IP address through DHCP.
I have seen that there was talk in some blogs about WAP200 no forwarding DHCP requests and I was hoping that updating the device to the latest release would have resolved the problems.
I was brought a WAP200 that was giving a client some issues. I've been told the first thing to try is to update/reinstall the firmware. I have the newest firmware file downloaded and saved, and I have the WAP200 plugged in and sitting on my desk.
I reset the access point and connected it directly to my computer with a patch cable, then entered the default IP address (192.168.1.245) to attempt to access the device. No go. Is that supposed to work and something is wrong with it? All I want to do is update the firmware, because if the device has been reset and the firmware reinstalled and it's still not working, then we'll just deem it defective and have it replaced.
i have Accesspoint WAP200 Model.iam trying to make repeater mode from other routers ( not linksys or cisco) but not works for me.when try to connect to the network which repeated with WAP200 its trying to take ip then failed ( its like DHCP not works in repeater mode)
View 2 Replies View RelatedI'm looking at a stack of WAP200 and WAP4410N APs. I'd like to use Cacti to track number of associations on each AP.What's the OID I should be querying? Are there multiple OIDs that would correspond to the multiple SSIDs? I'm running 2 SSIDs on all of them, and it would be extra nice to be able to track number of stations on each SSID, though the total number would also be acceptable as well.
View 4 Replies View RelatedFor a customer of mine I've installed 8 WAP 200 access points with an SF302 switch. The Access point are powered with POE. All seems to function properly: the clients are simple Android device and the connection appears solid.. We've a good roaming between access points (not seamless of course but is ok) and no particalur problems, also because the network is used to drive very LOW data (no internet): the clients opens a tcp connection to the server and sends only a keep alive packets over this connection.. Then sometime the server send a very small amount of data (some byte) to activate the display of the device and show a question.. the clients reply with some other byte of data and so on.. During an event of 3/4 hour we can do this 12/14 times, so the network load is nearly 0....
Last night the system suddenly stopped working: ALL clients (300) lost connection from their access points at the same time! How this can happens? The only reason that I can imagine is a power loss on the switch...
i have a problem with the AP WAP200, i can't make access to web setup. It gives to me the error "Unauthorised" without asks to me user or pass.
I tried to reset the AP and i tried to access with others pc and smatphones but the problem persists.
I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 1 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedI have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.
Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none
are found.
Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.
Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?
<script id="overlay_tmpl" type="text/html">// <div id="<%= overlayId %>" class="_mp3rocket_overlay_style" style="left: <%= overlayLeft %>; top: <%= overlayTop %>; width: <%= overlayWidth %>; height: <%= overlayHeight %>"></div> // </script>
I have an AIR-LAP1141-A-K9 it keeps rebooting itself. It seems to boot up and loads the flash and then shortly afterwards and before I get to console login it reboots.in reviewing what I've captured from the boot process is a message "Unexpected exception to CPUvector 200, PC = 1020" Below it is the following "Traceback - 0x1020 0x51351c 0x51351c 0x513c00 0x4FB1A8 0x4FB5B0 0x4F7FB8 0x191214 0x1912c8 0x57090 0x57398 0x1A5E50" I tried a couple google searches but didn't have any luck finding anything that matched what I have occuring.
View 5 Replies View RelatedI have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies View RelatedI have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
WAP200E access point that causes it to reboot after anything from 15 to 20 mins .I have run it off an injector and a POE switch, updated the f/w to WAP200E-ETSI-FW-2.0.3.0 and it still reboots itself .I have even been sent a new one from the supplier and it does the same thing.
View 5 Replies View RelatedI got my new comcast connection and using CISCO DPC3008 cable modem and EA6500 Wifi Smart Router. Internet works fine and then suddently the internet goes away. Further investigation shows EA6500 Wifi router just reboots every few hours and then wifi devices don't reconnect like it used to do with previous routers.
View 6 Replies View RelatedCheck to see if there is a firmware upgrade and there is. Well I updated it with the newest and only one out there. I did the upgrade, said sucessful and now it will just random reboot or something........ every few minutes the power light starts flashing....... then all the light go out, then power flashes again and it comes back up. I have tried many times to reflash it with that new firmware but no avail. I wish I had the old firmware back because it was working fine till I did this upgrade.
View 5 Replies View RelatedI have an issue when I use Airplay through my iPhone4S, my router reboots after 30 secs or so. I have a WRT54G2 v1.5 and the receiver is a Pioneer VSX-1021-K.
However, when I used Airplay through itunes from my laptop, it works just fine. In addition, when I borrowed my neighbors router's(BELKIN) it was working fine also. So this lead me to believe that it's my router that is causing the issue.
I have a E2500 router that until recently has been working fine, the router currently will reboot at random occasions. I have tried resetting the router to factory defaults to test if the firmware was an issue but both the factory default and the most recent firmware build(1.0.05 build 2) offered on the download support page. I have tried 2 different AC adapters to test power and two different Cat5 cables so hard ware wise everything is looking good. I am concerned that it may be an issue still with firmware or with the cooling fan and the unit may be overheating.
View 1 Replies View RelatedSo I have a WRT160N firmware v3.0 wired connection to my PC, and at least once a day my connection speed drops from 2mbs down to almost dial up speeds at 60kps. Just unplugging the router then plugging it back in seems to fix it every time. I've contacted my service provider and they say there's no issue on their end, and since I don't get this problem when I plug the modem directly to the PC I agree with them. I've done a factory reset and that didn't work. I've gone through the FAQ and can't find anything useful in there.
View 7 Replies View RelatedNew E4200v2 router, latest 2.0.26 firmware. Reboots on its own <or> locks up and requires power recycle 3-4 times a day. More frequent if I attach a USB drive to USB port. Reset to factory, only using as a router (no USB drive, no printer sharing, no TimeMachine backups, etc.)Still locks up or reboots 3-4 times a day. I need a reliable router that does not reboot so often.
View 5 Replies View Relatedi have router WRT45G ver 7 it work but when i want to access in web base utility the router reboot
info:
led power is on stable
led lan is on
led wlan on and the access point work
1.http:\192.168.1.1
2.enter user name and password (admin,admin)
3.hir the page begin to get after a few second the router reboot Page cannot be displayed completelty
i try :
- simple reset
-(30/30/30) reset and i enter in managment mode firmware upgrade
i don't try hardware reset
I upgraded my E3000 to a new E4200 several months ago. I use an SSL VPN to connect to work which worked fine on 1.0.01 and 1.0.02 but I upgraded to 1.0.03 to fix an issue where the router constantly reboots when I stream Netflix or Hulu and now the router reboots with Netflix, Hulu AND the SSL VPN tunnel initiation.
View 6 Replies View Related