I purchased 3 of these Wireless-G access points and none of them are plug and play. I am here because I have spent the last three hours trying to go through every step they suggest in the Quick Start Guide.
I tried entering in a web browser the default IP address and wait for a login that does not appear.
I have a wap200 with a static ipaddress e.g. 192.168.249.205/24 (it is for management and is in vlan 1). Firmware of the wap is 2.0.4.0. No gw and no dns. (they are not necessary) I export the config . I have a second wap200 and import the config.bin to the new wap. ThenI like to change the static address and the name of the new wap, but - and this is the problem - it asks me to fill out the dns (the address for primary dns cannot be 0 and 255), but I absolutely don't want that because there is no dns or gw (management only). And if I fill it out I cannot go the the internet with the wap.
So I also have some other wap200 where I could import the config.bin and change the static ip without giving a dns (firmware 2.0.1.0). can I go back to a previous firmware (Europe) and where can I find it. Looked for it, but seeing only the last one 2.0.4.0 etsi.Or is there another method to skip the dns with a static ipaddress?
I do have problems with remote management of a Wireless Accespoint WAP200.The WAP200 is connected to a router RVS4000 and works well..There are several nodes in the LAN, all static IP, all forwarded in the RVS4000..All nodes can be managed in the LAN as well as from outside..Exept the WAP200, from inside in LAN no problem, but from outside gives a 404 return.I build other similar LAN's, but the same, no connection.
View 8 Replies View RelatedI have a Cisco WAP200 Wireless-G Access Point - PoE/Rangebooster with the latest firmware 2.0.2.4-ETSI?I’m trying to set it up as a repeater, repeating the wireless signal from a Cisco 877W.I have configured the WAP200 with the same SSID, WPA key, and channel as the 877W.
I have changed the WAP200’s AP Mode setting to Repeater, and picked up the 877W’s MAC Address.The WAP200 is broadcasting and I can connect to the wireless network, but I don’t get DHCP. It’s almost like it’s still in Access Point mode.
I'm trying to setup a WAP200 as a wireless repeater and I am having some problems. The SSID I am trying to bridge is coming from a WRV210.
I on both devices I have the SSID, security, and channel set the same. The WAP200 is set to Repeater mode and I did a site survey to find the WRV210. The WRV210 is set to to allow the WAP200 repeat its signa using auto select, manual with site survey and manual actually entering the MAC address by hand.
Nothing seems to work. I can see the wireless next work but when i connect to the repeater I never get an IP address.
Network set up; wireless router (D-link DIR825) to Cisco switch (SD208p) and have Wap200 hooked to cisco switch to extend range up one floor. Can see it as wireless network, but cannot configure it with web browser. Address 192.168.1.245 just times out via pings as well. Have done all resets, power on reset, etc nothing.
View 3 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.
Should I be adding the additional MACs there?Does the WAP200 even support multiple VLAN/SSID?
Network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
is any way to get information about clients connected to an AP WAP200?
View 2 Replies View RelatedWhich AP's Wap200 can bridge with this ?
View 1 Replies View RelatedI have 3 WAP200 wireless-G access points. I have one set up as an AP the other two are set up as repeaters to the main AP.
My question is Do I need a lan connection to each repeater ?
also, do I need to create SSIDs for all three? & if so, do they need to be the same?
I have a Linksys WAP200 Wireless-G Access Point problem. It is SW version 2.0.4.0. I have it configured for a small network and the problem seems to be that it is not forwarding DHCP requests onto my DHCP server. I know that it is not a SSID or Key issue as when I give my devices static IP addresses, they communicate fine within my system. The only issue seems to be when the devices make DHCP client requests. I also know that the problem is not my DHCP server as it has the device's IP / mac addresses in its configuration file and other wired devices are able to communicate with it to get their IP address through DHCP.
I have seen that there was talk in some blogs about WAP200 no forwarding DHCP requests and I was hoping that updating the device to the latest release would have resolved the problems.
I was brought a WAP200 that was giving a client some issues. I've been told the first thing to try is to update/reinstall the firmware. I have the newest firmware file downloaded and saved, and I have the WAP200 plugged in and sitting on my desk.
I reset the access point and connected it directly to my computer with a patch cable, then entered the default IP address (192.168.1.245) to attempt to access the device. No go. Is that supposed to work and something is wrong with it? All I want to do is update the firmware, because if the device has been reset and the firmware reinstalled and it's still not working, then we'll just deem it defective and have it replaced.
i have Accesspoint WAP200 Model.iam trying to make repeater mode from other routers ( not linksys or cisco) but not works for me.when try to connect to the network which repeated with WAP200 its trying to take ip then failed ( its like DHCP not works in repeater mode)
View 2 Replies View RelatedI'm looking at a stack of WAP200 and WAP4410N APs. I'd like to use Cacti to track number of associations on each AP.What's the OID I should be querying? Are there multiple OIDs that would correspond to the multiple SSIDs? I'm running 2 SSIDs on all of them, and it would be extra nice to be able to track number of stations on each SSID, though the total number would also be acceptable as well.
View 4 Replies View RelatedFor a customer of mine I've installed 8 WAP 200 access points with an SF302 switch. The Access point are powered with POE. All seems to function properly: the clients are simple Android device and the connection appears solid.. We've a good roaming between access points (not seamless of course but is ok) and no particalur problems, also because the network is used to drive very LOW data (no internet): the clients opens a tcp connection to the server and sends only a keep alive packets over this connection.. Then sometime the server send a very small amount of data (some byte) to activate the display of the device and show a question.. the clients reply with some other byte of data and so on.. During an event of 3/4 hour we can do this 12/14 times, so the network load is nearly 0....
Last night the system suddenly stopped working: ALL clients (300) lost connection from their access points at the same time! How this can happens? The only reason that I can imagine is a power loss on the switch...
i have a problem with the AP WAP200, i can't make access to web setup. It gives to me the error "Unauthorised" without asks to me user or pass.
I tried to reset the AP and i tried to access with others pc and smatphones but the problem persists.
I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 1 Replies View Relatedi have issues with my 3 Cisco WAP200, they are rebooting after uptime from 9 to 20 days, i've tried to use latest firmware available 2.0.4.0 but it makes no differance to 2.0.2.4. I can't see logs to point out the problem (by SNMP i found only something like "out of swap space", and nothing by web interface).
View 3 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedAny issues with the WAP200 and web connectivity? The internet stays up, but after awhile, any browser I use cannot hit the web. Email, chat, and any other internet reliant apps are fine.Just web.
View 1 Replies View RelatedI'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies View RelatedWe've got a network consisting out of Cisco 3750 and 2960 units on which STP is enabled. We are trying to get a WAP200 working in this environment. Problem is that the WAP200 is sending out STP data every 2 seconds (checked with Wireshark) wich is causing mayhem on the network. The situation will not settle down to a stable situation.Question:Is there any way in which the STP traffic generated by the WAP200 can be disabled ?
View 2 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.Should I be adding the additional MACs there?
Simple network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
Is there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedI'm trying to set up my DIR-655 so I can use VPN to access my work PC. How can I set this up?
View 2 Replies View RelatedI have a DIR-655 B1 router. The firmware is 2.00 NA. Just to clarify, the DSi itself does work with WPA, but the games only work with WEP. I made a guest account and set it to WEP and it still does not work. I have tried making the main connection WEP as well, but when I go on the game and try it, it says it is WPA and not WEP. My friend has a DIR-655 as well, but the hardware and firmware version are different. Her games work flawlessly.
View 10 Replies View RelatedDoes aps work with Wcs ?? .
View 4 Replies View RelatedI've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
View 1 Replies View RelatedHave a Fujitsu Siemens Esprimo P2430 PC and am trying to connect it to my Virgin Media super Hub via a Netgear WN1111 USB 2.0 AdapterWireless-N. Software is loaded perfectly fine and signal is excellent but it refuses to load any web pages unless I refresh a zillion times. Internet works excellently on my laptop so am stumped. No connection malfunction is diagnosed
View 8 Replies View RelatedI want to get wifi for my laptop and ipod at work, i cannot add a router to the system lol not a option. Is there a thing i can plug into the dekstop here so i can get the internet off of it? There has to be somthing out there that can do this. Because these computers are wired.
View 7 Replies View RelatedI bought cisco AP (air-ap1142-e-k9) and we know this ap works with 802.11a/g/n same the description note on the package cartoon but my problem is when i configure that ap its work only with 802.11a/g i tries to make it works with 802.11n but fail .
View 3 Replies View RelatedI currently have a UC540 system with 12x aironet 1130 APs. Seamless roaming does not seem to work, and the recommendation seems to be to introduce a WLAN controller.
View 4 Replies View Related