Any issues with the WAP200 and web connectivity? The internet stays up, but after awhile, any browser I use cannot hit the web. Email, chat, and any other internet reliant apps are fine.Just web.
View 1 Replies
I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies View RelatedWe've got a network consisting out of Cisco 3750 and 2960 units on which STP is enabled. We are trying to get a WAP200 working in this environment. Problem is that the WAP200 is sending out STP data every 2 seconds (checked with Wireshark) wich is causing mayhem on the network. The situation will not settle down to a stable situation.Question:Is there any way in which the STP traffic generated by the WAP200 can be disabled ?
View 2 Replies View RelatedI have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.Should I be adding the additional MACs there?
Simple network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000
Bought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 4 Replies View RelatedWhich AP's Wap200 can bridge with this ?
View 1 Replies View RelatedI have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedSetting up my wifi network with an old BEFSR41 Router and WAP11 wireless access point. Have laptop with XP Pro that connects just fine without encryption but as soon as I try to use WEP I get the "Limited or no connectivity" error. When prompted, I type in the same passphrase as the one I used for the WEP 128bit encryption while setting up the WAP11 for my network.
View 4 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View Relatedi have a problem with the AP WAP200, i can't make access to web setup. It gives to me the error "Unauthorised" without asks to me user or pass.
I tried to reset the AP and i tried to access with others pc and smatphones but the problem persists.
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCannot access configuration page for WAP11 Access
View 9 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedHow do I change the channel on my WAP45. I can't connect I get a message unidentied-no access
View 1 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedI am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.
View 3 Replies View RelatedMy network is such that I want to extend the signal of the GUEST account. I have a WAP54G set up for that purpose and am getting a very strong signal. I can access the main network, but not the Guest, I cannot even see the GUEST access. Any setting change that needs to be made that will allow me to access the GUEST account from the Access Point?
View 2 Replies View RelatedI just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedBought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?
View 1 Replies View RelatedI am not able to access my wireless access point anymore. I tried to access the web configuration in my browser as I have in the past 192.168.1.245, but I have no luck there. I tried to reset it by holding the reset button for 10-30 seconds, and I have no luck with that. What I have noticed on the AP is that the ethernet light keeps going out. The only light that is lit on my AP is the power and sometimes the ethernet light. My AP is connected to my router which I am able to gain access to the internet from any devices connected to the router except the AP. I have a router (E2000), a WAP4400N, and switch. I want to keep my wireless access separate from my business network. I cannot get my WAP4400N to work anymore.
View 1 Replies View RelatedI would like to ask if its possible to remotely access a WAP54G?
View 3 Replies View Relatedmy wap54g is not working even i hold reset butoon for 60 second it not woring even my linksys wap54g reset button is not work for reset it, It not do any thing and still i cant accest is web interference
View 9 Replies View Related
