Linksys Access Point :: WAP200 Is Sending Out STP Data Every 2 Seconds

Apr 18, 2008

We've got a network consisting out of Cisco 3750 and 2960 units on which STP is enabled. We are trying to get a WAP200 working in this environment. Problem is that the WAP200 is sending out STP data every 2 seconds (checked with Wireshark) wich is causing mayhem on the network. The situation will not settle down to a stable situation.Question:Is there any way in which the STP traffic generated by the WAP200 can be disabled ?

View 2 Replies


ADVERTISEMENT

Linksys Access Point :: WAP200 Cannot Hit Web Connectivity

May 31, 2011

Any issues with the WAP200 and web connectivity?  The internet stays up, but after awhile, any browser I use cannot hit the web.  Email, chat, and any other internet reliant apps are fine.Just web.

View 1 Replies View Related

Linksys Access Point :: Unable To Configure WAP200

Sep 17, 2008

I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.

View 3 Replies View Related

Linksys Access Point :: WAP200 Multiple SSID With Trunk

Aug 10, 2011

I have two WAP200's code level version 2.0.4.0 connected to two SFE2000 24port, one switch per building. I have 3 vlans that I want to bridge between those two switches. I know the trunks on the switch are setup correctly because I can connect them directly and test all vlans.
 
I am able to get the untagged Vlan 1 to work fine with the bridge, but I have issues with the tagged Vlans 2 and 3. I have checked that I have the correct SSID tied to the correct Vlan number. I cause the whole network to lock up when I try to add the other SSID MAC addresses to the AP Mode -> AP Mode -> Wireless Bridge -> "Remote Wireless Bridge's MAC Addresses:" section. The wireless lights and ethernet lights go solid.Should I be adding the additional MACs there?
 
Simple network diagram: SFE2000 --trunk-- WAP200 --(((((3xSSIDs)))))--WAP200--trunk--SFE2000

View 1 Replies View Related

Linksys Access Point :: X3000 And WAP200 - Can't Adjust Wireless Repeater Mode

Feb 7, 2013

Bought wap200. I can't adjust the wireless repeater mode. Linksys x3000 supports wap200? What settings need to be made?

View 4 Replies View Related

Cisco Wireless :: WAP200 Access Point Bridging

Aug 6, 2012

Which AP's Wap200 can bridge with this ?

View 1 Replies View Related

Cisco Wireless :: Wap200 Access Point Configuration / Port Disabled

Mar 27, 2012

I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.

View 1 Replies View Related

Cisco :: WAP 200 Wireless G Access Point Keep Sending Empty Alarm Email

Nov 5, 2012

We have a WAP 200 wireless G access point.  It worked perfect before.  About two weeks agao,  we didn't change anything, it began to send empty alarm email every 10 minutes.  We upgraded the software to newest version,restarted it several times. But till now, it still keep sending empaty alarm email. 

View 1 Replies View Related

Sending 5 100-byte ICMP Echos To 1.1.1.2 Timeout Is 2 Seconds?

Jul 7, 2011

Sending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:Success rate is 100 percent (5/5), round-trip min/avg/max = 16/20/28 msround-trip min/avg/max = 16/20/28 ms

View 12 Replies View Related

Security / Firewalls :: Something Keeps Sending Data Over The Connection

May 7, 2011

having recently downloaded a bandwidth monitor widget, i notice that something is sending 1.625kb of data, OVER AND OVER. i am experiencing zero issues with my pc functionality, but am concerned about what is sending data out from my pc.in desperation, i tried a 3rd party firewall, zonealarm. even after installing it, the data continues to be sent. i have looked through my running processes, ending several auto-updaters, closed my browser and anything else i can think of that might use my internet.

View 3 Replies View Related

Cisco Wireless :: 2602 -Access Point Getting Power But Not Data

Apr 21, 2013

I have a problem, where we are installing a Cisco 2602 access piont, the AP is getting power as the lights are on (changing colors Green, White, Red). In the switch side the LED for the interface is blinking green only when I chosse PoE. Also I cannot see the AP in CDP neighbours.
 
It seems to be a physical problem but the cable is tested and showing connected for all pairs and parallal (straight) connection.
 
Access Point was connected directly to the same interface (I mean with a patch cable to the switch) and working

View 4 Replies View Related

Cisco 2100 - Data Not Sending Or Receiving From Modem?

Oct 26, 2012

I'm using Cisco 2100 cable modem. It worked fine until some time later where the Data Send & Receive LED's stopped blinking. A man came to check if the cable was the problem by replacing it, but it wasn't. He claims it might be related to the laptop. I have tried several times restarting it. (I'm using mobile broadband) I would really like fast rather than slow internet ( I was limited so now it's slow but free)

View 14 Replies View Related

Cisco :: 3845 Traffic Logs Set To Refresh Every 1 Second But Data Comes In 5 Seconds

Jun 28, 2011

when using SNMP on our cisco 3845 the traffic logs are set to refresh every 1 second but the data seems to come in 5 sec burst.so does not some a real time status of the interface throughput.

View 2 Replies View Related

Linksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?

Nov 1, 2012

How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.

View 1 Replies View Related

Linksys Access Point :: WRT54G - Unable To Find Access Point In Home Network

Aug 29, 2009

I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1.  My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
 
I found directions in the forum for a setup using the LG BD390  but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold  from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
 
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi. 

View 3 Replies View Related

Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines

Jan 18, 2012

We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.

View 3 Replies View Related

Linksys Access Point :: WAP54G Access Point Setup After A Reset?

Jul 9, 2006

I had to reset my access point but the login screen fails to appear to lock the router.  I don't have the setup wizard disk.

View 9 Replies View Related

Linksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point

Jan 17, 2013

I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?

View 1 Replies View Related

Linksys Access Point :: WRT320N Access Point Vs Range Extender

Dec 14, 2011

Have a WRT320N router at one end of the house in the basement.  Would like to boost signal to other end of the house.  Which product should i use, an access point or a range extender?  My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.

View 1 Replies View Related

Linksys Access Point :: WAP4410n MIBs Or OIDs For Access Point

Jul 3, 2012

I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?

View 1 Replies View Related

Linksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?

Apr 25, 2011

I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
 
 The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
 
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
 
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.

View 3 Replies View Related

Linksys Access Point :: Repeat WAP54G Access Point?

Aug 25, 2011

What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G. 

View 4 Replies View Related

Linksys Access Point :: WRT120N - Cannot Connect To An Access Point

May 10, 2013

I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
 
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.

View 1 Replies View Related

Linksys Access Point :: Configure WRT120n As An Access Point?

May 1, 2012

Is it possible to configure WRT120n as an access point?

View 1 Replies View Related

Linksys Access Point :: E3000 Configuration As Access Point?

Apr 6, 2011

I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.

View 1 Replies View Related

Linksys Access Point :: Way To Find Mib For WAP54G Access Point?

Feb 10, 2012

I have tried to find mib for my Linksys WAP54G acces point  without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?

View 1 Replies View Related

Cisco Wireless :: WAP200 Unauthorised Cannot Make Access To Web Setup

Feb 20, 2013

i have a problem with the AP WAP200, i can't make access to web setup. It gives to me the error "Unauthorised" without asks to me user or pass.
I tried to reset the AP and i tried to access with others pc and smatphones but the problem persists.

View 5 Replies View Related

Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?

Apr 16, 2013

I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?

View 6 Replies View Related

Linksys Access Point :: Cannot Access Configuration Page For WAP11 Access

Jun 12, 2007

Cannot access configuration page for WAP11 Access

View 9 Replies View Related

Cisco Wireless :: Point To Point Access Point 1262 Bridging

Feb 27, 2013

How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.

View 12 Replies View Related

Linksys Access Point :: Cannot Change Channel On WAP45 - Unidentified / No Access?

Jul 5, 2012

How do I change the channel on my WAP45. I can't connect I get a message unidentied-no access

View 1 Replies View Related

Cisco Wireless :: Upgrading 1042 Access Point To Lightweight Access Point

Apr 20, 2012

I had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.

View 4 Replies View Related

Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?

Nov 24, 2011

I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved