I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 RepliesI'm receiving this error on a WAVE-574 appliance. The primary interface is configured and I can ping between the wave and the central manager.
View 1 Replies View RelatedI do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
I am developing CAP1602I & 2500 Controller.The CAP1602I-E-K9 can't register with the 2500 controller. [code] logging appears: capwap can't process uncryped data..I even didn't configure capwap on CAP1602.May I know if CAP1602 doesn't support LWAPP? Why LWAPP doesn't work?According to the logging, I also tried to configure the "Data Encryption" on 2500 controller ( according to 7.0.116.0 guide)
"Cisco 2500, WiSM2, WLC2—By default, these platforms do not contain DTLS. To turn on data DTLS, you must install a license. These platforms have a single image with data DTLS turned off. To use data DTLS you will need to have a license."Note If your controller does not have a data DTLS license and if the access point associated with the controller has DTLS enabled, the data path will be unencrypted. I should purchase a license? or, if I can configure the CAP1602I to don't encrypt data?
Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies View RelatedWe have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies View RelatedI have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
We have a 5508 controller that manages AP's at approximately 20 branches - each branch has their own subnet. We have a single branch (subnet) with new 2602 AP's that will not register with the controller. All communications to this subnet appear normal and there are no ACL's in place between the AP's and the controller. The AP's are able to resolve the controller IP address via DNS and begin the registration process but then timeout. We have successfully installed 2602 AP's at other branch locations and they register with no problems - this is only a problem at a single branch. I've attached some debug messages below for a single AP (this is a production environment so I parsed un-necessary info) and also included the console messages from a different AP (the console messages on the AP's are the same). There are currently 9 AP's at this location and none of them will register.
Debug Capwap Events:
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Discovery Request from 10.29.9.190:44306
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 300, joined Aps =272
[Code]......
We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies View RelatedJust tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies View RelatedI am trying to configure the Wism running on a 6500 switch.... I have configured the DHCP scope for the AP on the controller itself with the same subnet as of the management for the controller. The AP gets the IP but once it restarts it doesn't register to the controller, this is the log i get on the AP when consoled into it. [code]
View 6 Replies View RelatedI have this version Ap "c1200-rcvk9w8-tar.124-21a.JA2" and a WLC 5500. When i connect the ap to the network i can ping from ap to wlc and the wlc to ap, but the proccess of lwapp messages give errors on the Ap when the Ap try to download the image from wlc and could not join the wlc. why this could be? this is the info of the wireless lan controller.
View 6 Replies View RelatedRegion : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : 0.6.0 1.0 v0001.0 Build 130108 Rel.54595n
ISP : TPG
RE: Voice SIP Account Phone Number Not Accepting 2 Characters My ISP TPG VoIP SIP account phone number is my TPG username rather than an actual normal telephone number. When I enter my 2 characters TPG username 'xx' as my TPG VoIP SIP account phone number as the 'Phone Number' field in the 'Voice - SIP Account' modem router management page on the LAN IP 192.168.1.1, then I press the 'Save' button, I encounter the error message "The length of 'Phone Number' is out of range[3,32]."I believe this error is due to my TPG SIP account Phone Number’ is not within the TD-VG3631 ‘Phone Number’ character length range from 3 to 32 inclusive.My old modem can register to my TPG VoIP account successfully with my TPG username 'xx' as the VoIP SIP account phone number.
I have contacted my ISP TPG and tried to get an actual VoIP SIP phone number. However, TPG does not provide an actual VoIP SIP phone number to their customers. TPG states I should use my TPG username as my VoIP SIP account phone number. They ask me to contact TP-Link to resolve the aforementioned error.Is there a way I can enter only 2 character TPG username as my VoIP SIP account phone number in the browser management page of the modem router? i.e. workaround, request TP-Link for a new firmware fix or else?
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedRegion : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version :
ISP : Engin
i purchased this new modem TD-VG3631 to replace my old one, Finished the internet configuration, it's ok, i can go to internet smoothly. however when i configured the voip function, i encountered a big problem, even i have entered all info which provided by Engin into your modem, it doesn't work. the status always down..Very sure it is not my account problem, because if i enter these info into my old modem , it works very well.
[code]...
I need to run a windows hyper terminal program between my POS register which has a serial RJ11 port to my PC db9 male port
View 2 Replies View RelatedI have tried the config-register command and it is not available. Here is part of the show ver command. I want to change the config-reg from 0xF to 0x2102.I have run into this before but don't remember how to correct it.....I think I have to use the boot command but not sure. Here it the output show ver Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on?System image file is "flash:c2960-lanbase-mz.122-25.FX/c2960-lanbase-mz.122-25.FX.bin"cisco WS-C2960-24TT-L (PowerPC405) processor (revision A0) with 61440K/4088K bytes of memory.last reset from power-on
4 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.64K bytes of flash-simulated non-volatile configuration memory.
Model number : WS-C2960-24TT-L
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)FX C2960-LANBASE-M
Configuration register is 0xF
I'm having troubles with a cisco 877 router, it keeps changing itself to either 0x2101 which is good, or to 0x3100 which is bad because it messes up my bautrate to 1200 instead of 9600.it doesn't seem to matter if I change it, it will still tell me that it will change at next reload. [code]
I have never seen this before.the command in conf t : configuration-register 0x2101 is not working, played with wr mem or copy start run neither of one useful.
Whenever I go to sites like godaddy.com or mydomain.com to register a personal domain, they only offer me sites like url...What can I do? Computers have lots of memory but no imagination..
View 1 Replies View RelatedWe have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
I am trying to implement a small VoIP LAN (you can see the lan in attachments)for a personal project. I am using:
- 2 x XP (on which i installed Cisco IP Communicator 7.0.3.0)
- 1 x Ubuntu (running GNS3 with a c3600 Router)
The problem is that the phone which is not in the same LAN with the tftp server cannot register.
1) Can a phone register to a tftp server from another LAN ?
2) If the answer for 1) is yes, what am i doing wrong (you can see the details in the attachments)? I mention that the ping works well anywhere in the LAN.
I am having two 6509E working in VSS and both are working fine. But the configuration register of command "remote command switch show boot" is 0x8000 which is different from that of RP (0x2102) .Now i want to change the value of configuration regsiter of SP to 0x2102.
View 1 Replies View RelatedI have just upgraded one of our 4400 to 7.0.98.0. Most of the AP re-registered with out issues. I have two AIR-LAP1142N-E-K9 on a remote site that will not re-register.I have pointed them to another 2125 WLC (7.0.98.0) and they register fine. Point them to yet another 4400 (7.0.98.0) I get the same issue.I am getting this error when the register on the 4400s.*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'abzewwlc'(index 1).*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller *Jan 11 07:05:55.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 144.46.211.5 peer_port: 5246*Jan 11 07:06:55.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 144.46.211.5:5246 I suspect it may be as they both have In the client config.Then again maybe not.Configured Switch 1 Addr 158.139.177.203Configured Switch 2 Addr 144.46.214.25
Question 1 if I do a "clear config except static IP" will I still be able to telnet tp them or will they default to no telnet no ssh ?
Question 2 any idea how to get past this DTLS error ?
Facing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
I am implementing Cisco Network Access Control with Wireless Controller 5508 (WLC5508 below) . Could you tell me how to register WLC5508 as SNMP Agent for Cisco Access Manager (CAM below) ?
[System Information]
IOS version of WLC5508: 7.0.98.218
Version of CAM: 4.8.0
[Code]....
I succeeded to register WLC5508 by using IP address of Service Port on the CAM Web Console. But WLC5508 has only one Service Port, which has no redundant port. I want to register it by usin Management Interface, which has backup port. It is also desirable to implement redundancy of Service Port if possible.
I am using PC to mobile dialer. It was working fine but now I am unable to login to my wowcall account due to error - Unable to register to SIP server.
View 1 Replies View RelatedI have just purchased SLM2016T-UK (SG200-18) and trying to register the warranty online (was told by the reseller to do so) but I can't find any link direct me to the correct site.
View 4 Replies View Related I have installed 2 ACS 5.2 appliances, the two appear as Primary. When I try to register one of them with the other one using "System Administrator -> Local Operation -> Deployment Operations" I get the following message:
This System Failure occurred: Unable to authenticate with node.. Your changes have not been saved.Click OK to return to the list page.
I have tried with both "ACSAdmin" and "admin" users with their respective passwords.
Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies View Related