We have open a division in the UK and are using DSL as a back up to a T1-E1, so I was going to use a standard DSL Modem but thought the WiC-1ADSL-I-DG would be better. However I can seem to get the card up and running. Here is the interface config and sh int atm.
interface ATM0/1/0
ip address dhcp
ip access-group 102 in
ip inspect SDM_LOW out
[code]....
That's part of the sh int amt.
What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedI have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
I have a Cisco 2811 running Advance Enterprise v 15.1-2. I've just configured it using ccp for internet access (on 2 lines) and a firewall. The configuration is pretty much all default and I used the ccp wizard to create a 'medium-secure' firewall. I have 2 blocks of public IP addresses for my internal network and for the DMZ. The 2800 is configured as follows:
- 2 x default routes. one to each dialer.
- 6 zone pairs as follows:
- ccp-zp-self-out (seems to mostly work... I can ping any IP address from a console but not a hostname)
- ccp-zp-in-out (works fine, both interfaces seem to be in use)
- ccp-zp-in-dmz
- which by default set to ccp-permit-dmzservice
- which inspects ccp-dmz-traffic
- which matches group dmz_traffic and has a class map dmz-traffic
- cnc-zp-dmz-out which is set to ccp-inspect. (my own zone pair to allow systems in the DMZ zone to see the internet. This works fine.)
- ccp-zp-out-dmz (works fine. I can see my web server from any system outside my own network)
- ccp-zp-out-self (which, I guess allows anything permitted to get to the 2811)
Internet works from within the DMZ and in-zone. The outside can access my dmz servers. The inside can access most things on the outside using the firewall rules.
1) Although I have the zones set up to allow the same access from in->dmz as I do from out->dmz and out->dmz seems to work, I cannot seem to access anything in the dmz from the inside.
2) When setting up the firewall I ticked the box for 'allow PPTP clients to make connections from the inside' (or something like that). I cannot seem to make a PPTP connection from my workstation.
I have scoured the internet for guides, looked through these forums & the cisco configuration guides and experimented all day but still cannot figure this out.Do I need a special route between the inside and dmz? I have seem references to static routes on ASA firewalls but the command 'static (inside,dmz)...' does not work on a 2800 series router.
We have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
I have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies View RelatedI have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
I had a question regarding the Cisco 2811. I tried fitting an NM 2FE-2W card and the fast Ethernet interfaces of the module never get recognized. Is there a special command to enable it or isn't the module supported at all by the router. If not , is there a way to have the router possess more than the 2 Fast Ethernet interfaces it already has? Let me know if any more info is needed from my end.
Another question I have out of curiosity. Is it possible to make the controller T1 port of a VWIC 1MFT-T1 or a VWIC 2MFT-T1 act as a fast Ethernet.
what routed ethernet card (WAN) can be inserted in Cisco 2811? I wan to replace 2Mbps Framerelay to 10 Mbps
View 5 Replies View RelatedSo I just finished installing ClearOS and configuring my network, but I can't figure out how to get it to boot without the video card. It's currently running with a 4870, but I want to take it out for the power savings.My motherboard is an ASUS P5Q-E and I haven't really found any information on how to do this or if it is even possible
View 12 Replies View Relatedhave remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
I am facing the problem as my CISCO router is detecting the RS 530 DCE cable as DTE 530idb. I am using this cable for X25 link connectivity. The same cable has worked for more than 1 hour with detecting the cable type as 530 DCE, but suddenly it stops the X25 data transfer. After that the cable type it is showing as DTE 530idb.
Below troubleshooting already carried out.
1. Changed the slot, but same output.
2. Removed the cable & reconnected, but same output.
3. Without connecting to the DTE device also, the cable type is showing as DTE 530idb
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies View Relatedi am soon to be purchasing and installing a wireless card in my workshop pc and wondered if you could give me some pointers on which type to get etc , and any istallation tricks or problems i may come across , the sytem i have is a m621 acer running on xp pro ! i am currently running on a dongle at the moment , would a internal be benfical ? would it improve performance etc
View 2 Replies View RelatedI have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
Here is my current config build for a Cisco 2620 using a Wic-1ADSL to connect to a Qwest ADSL ISP:
interface FastEthernet0/0
ip address 172.16.0.1 255.255.0.0
ip nat inside
no ip mroute-cache
[code]...
For some reason, it won't connect at all. I've changed the callin requirement on the ppp authentication between "callin" to "callout" - even removed the line completely for a no-authentication scenario.The only responses that come back on a repetative nature when doing a debug are:
Vi2 PPP: Authorization NOT required
and
Vi2 PPP: No remote authorization for call-out
I’m testing a 1841 with 2 WIC-1ADSL cards, but the connections are dropping every 30-50mins. If I swap the cars out for HWIC-1ADSL’s then the lines are stable. I’ve had the profiles on the lines dropped the 4mb down and 512k up but I’m still getting the same issue.
I’ve tried a few 1841’s with various IOS’s and different WIC’s but still get the same result.
I have a Cisco ASA5505 with Frontier ADSL. I broke into their crappy little modem and obtained the settings needed to replace their modem with a 2621 router with a WIC-1ADSL module. I have a static IP from Frontier which is on my ASA5505 and the Dialer interface on the 2621 gets its address from Frontier via DHCP. There are devices behind the ASA which I need access while in the field, IP Cameras, Seed Treater, etc., so I have Anyconnect running on the ASA and can access everything from my laptop, iPhone and iPad from whereever. The issue arises when my laptop is in house and communicating with my parent company and I try to make a cell phone call off the network extender. The call is choppy since there is no QoS and the data is strangling the voice. Since I have control over the 2621, I added another network and NAT it into Frontier without them knowing. I have since placed the network extender on this network as well as a WAP200 that is wide open for my customers when they are in the office. Doesn't fix the problem but...
I have now added Evertek Wireless internet with a static IP also but they use a reservation based on the MAC Address of my interface of the ASA. This plugs directly intot the ASA via ethernet (I would assume their antenna is just a wireless bridge). I set route tracking on the Evertek side and use the Frontier as a backup and all devices on my NAT network still funcion on Frontier DSL and all my nornal data traffic is out Evertek. The issue is that the Evertek Wireless is not very fast or reliable (today in during a snow storm, it could barely keep an internet connection). And I had a problem with Anyconnect using either connection. I got that working. But think that the "ip address x.x.x.x y.y.y.y dhcp setroute" on the Evertek side messed things up from a routing standpoint when I would connect from the outside on the Frontier side. For testing, I switched the tracking around and now the connection on the Frontier side does not work but that is besides the point.
Frontier is going to try out an ADSL/2 connection next week which brings up another issue; all Frontier connections come into my buidling on a single 4-pair wire so if they go down, all my internet except the Evertek goes down. I have a Raven Slingshot coming for installation shortly that cannot go down; it will provide RTK (sub-inch accuracy GPS) to my customers that have auto-steer and auto-shutoff capabilities in their tractors via cellular data modem. So, while they are planting their crops in the field, if my connection goes down, their tractor will not function.
I also had a Cisco UC320W but it died a few days after it went off warranty so I replaced it with a Dell Server running 3CX IP PBX that supports Cisco SPA525G2 and SPA501G IP Phones. There is a 3CX iPhone app that allows me to receive calls while in the field, it uses a proprietary tunnel that I have open on the ASA. With 4-pair coming into my building, I will be left with a single 1-pair for phones so I am considering a SIP provider instead.
Can/should I move the Evertek ethernet to the third ethernet interface on the 2621 and track the Frontier DSL against the Evertek (backup) on the 2621 side and use the ASA to track the ADSL/2 against the 2621? Should I acquire an 1841 (or some other device that suppports the HWIC) with a ADSL/2 card and use HSRP between the 2621 and 1841? Is that even possible?
I just recently (and very expensively) purchased a HWIC-1ADSL for my 1841 router.
Unfortunately, it doesn't display in the configuration - nor any lights appear on it for power/link.
My first guess is I need to upgrade my IOS. The current version on my 1841 is 12.4(17). Which appears to be pretty current.
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View RelatedI need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies View RelatedI think I am having problem with my network card I am running windows 7 with Dell wireless 1390 WLAN Mini-Card lots of times the signal is low and I get the error message no internet connectivity or some other error message that I am not being able to connect to the network provided by my wimax modem, Is there any program that I can download to test if there are any errors related to the network card or any way to fix this?
View 3 Replies View RelatedMy setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies View RelatedI need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
I want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies View Relatedi have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies View RelatedI have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies View RelatedI want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I have a 2811 that I can remotely VPN to using Cisco VPN client however I cannot see the internal admin network (10.35.5.0).
Current configuration : 4845 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.