Cisco Infrastructure :: 2811 - Router Config-register 0xC502
May 31, 2010
I have Cisco 2811 Router and few days ago my router doesn't work correctly. I checked config and found config-register was changed (0xC502).
HUV_Murun#sh version
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
HUV_Murun uptime is 23 hours, 36 minutes
[code]...
Configuration register is 0xC502. What is the meaning of this config-register (0xC502) and how can be changed config ?
View 3 Replies
ADVERTISEMENT
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
Feb 6, 2007
I have tried the config-register command and it is not available. Here is part of the show ver command. I want to change the config-reg from 0xF to 0x2102.I have run into this before but don't remember how to correct it.....I think I have to use the boot command but not sure. Here it the output show ver Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on?System image file is "flash:c2960-lanbase-mz.122-25.FX/c2960-lanbase-mz.122-25.FX.bin"cisco WS-C2960-24TT-L (PowerPC405) processor (revision A0) with 61440K/4088K bytes of memory.last reset from power-on
4 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.64K bytes of flash-simulated non-volatile configuration memory.
Model number : WS-C2960-24TT-L
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)FX C2960-LANBASE-M
Configuration register is 0xF
View 6 Replies
View Related
Jun 5, 2012
Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies
View Related
May 13, 2013
I get stuck in one case. One of my customer has two FTTH lines. I have to config PPPoE in routers. In one line I config succesfully, but one line never up. I call to ISP they ask me to config extactly VLAN id 10 in the physical subinterface. But in subinterface there is no command "pppoe-client dial-pool-number". I check the old modem FTTH, they also config VLAN 10 in Wan interface. I tell ISP why we have the same two FTTHs, but two differrent config ways. ISP says because the two line run in two different infrastructure, two different devices. I don't know how to do now? stay in customer side or ISP side. Here is my PPPoE config:
interface FastEthernet0/0
no ip address
duplex auto
[Code].....
View 4 Replies
View Related
Jul 11, 2011
We have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
View 3 Replies
View Related
Sep 13, 2012
Facing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
View 4 Replies
View Related
Sep 29, 2002
I X modem an IOS file to my 2620 router and in the process set the console bps to 115200 which changed the register to 0x3922. Now when I try to connect from the console with any bps, I get garbage!
I can connect from the AUX port and get to the User Exec. mode but since no privileged password is set, I can't get any further to change the config register back to 0x2102.
View 6 Replies
View Related
Mar 22, 2013
I need to get the latest firmware for a 2811 router but I am unable to download it. What is the best way to get hold of this can I just contact a local Cisco reseller n Monday or is it more complicated than that?
View 2 Replies
View Related
Jul 9, 2012
Seeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies
View Related
May 24, 2012
I have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
View 1 Replies
View Related
Jun 20, 2012
I use a cisco 2620 voice gateway with a module NM-HDV-2E1-60. Tell me how you look at snmp for Cisco 2620 load E1. For 2811, I found oid 1.3.6.1.4.1.9.10.19.1.1.4
View 4 Replies
View Related
Nov 30, 2011
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies
View Related
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 22, 2008
Why can I not register a WAG160N router with Linksys? Is this because these devices are not sold in the US?
View 4 Replies
View Related
Jul 15, 2011
Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies
View Related
Dec 24, 2010
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies
View Related
Oct 10, 2008
I am having problems with my RV042.I have a Intervoip(url...) account for VOIP.
When I try to register the intervoip account to the internet I don't get any kind of reply. My VOIP server just keeps requesting to register the SIP account, but gets no reply.
When I connect an other router to my ISP modem, the register just goes fine. However the RV042 blocks something I don't really know what the cause could be.I installed wireshark to monitor my network traffic.
When I monitor registering with intervoip with the RV042, I see requests but no replies from intervoip, the VOIP server keeps requesting, but doesn't get any reply.
When I monitor registering with intervoip with an other router, I see requests from the VOIP server, and replies from intervoip initiating my intervoip account and everything goes well and registers. The following I tried:
- Forwarding port 5060 to private ip
- Putting private ip in DMZ
- Disabled the firewall
All without result. (Also tried them all at once)
View 8 Replies
View Related
Jun 17, 2012
I have a task for a config I have not done before. I'm replacing an older 831 and PIX with a Cisco 881 router with Firewall feature set. The router receives its public IP address dynamically and there is a static public IP range also assigned with a couple of NAT statements on the PIX for a few public IP's.I'm ok with the core router config but the range is where I'm a little stuck. Current setup is as follows
Internet ---------- Router( Public intf Dynamic IP----internal intf Range IP)Router-------------PIX (outside intf Range IP---------Inside intf private net)Pix-------
As per the aboive the PIX had a public IP address from the range on the outside interface with a default route to the Router inside interface which uses a public range addres.
With my proposed config I've setup the outside interface as dynamic and just created my nat statements for the Range IP's. I believe I'm correct that I do not need to actually have a Range IP address configured on the router?
View 2 Replies
View Related
Jan 23, 2011
Had no problem getting into IOS via Terminal and changing the host name, username and password. Then I loaded the Cisco CP Express onto a system and got into the web config. Problem is....the default IP is 10.10.10.1 / 255.255.255.248 and I wanted to change it to 192.168.1.1 / 255.255.255.0 I did it in the web interface and it applied to the router, but after that I could never bring up the web interface again on 192.168.1.1. Checking IOS showed that the new 192.168.1.1 did indeed "take". I even added an access list for the 192.168.1.0 network.
View 8 Replies
View Related
Jun 7, 2011
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies
View Related
Dec 22, 2010
I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]
View 2 Replies
View Related
Mar 7, 2011
I need to run a windows hyper terminal program between my POS register which has a serial RJ11 port to my PC db9 male port
View 2 Replies
View Related
Feb 4, 2013
Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect
Things that I have already tried:
- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.
- Tried with different browsers.
- Tried with seperate computer with different OS's (Mac and PC)
- Unable to flush dns because I get this error: CMD prompt error message .
- Have factory reset router a few times now.
- Unplugged, left off for 20mins-2hours.
View 16 Replies
View Related
Mar 30, 2011
I'm having troubles with a cisco 877 router, it keeps changing itself to either 0x2101 which is good, or to 0x3100 which is bad because it messes up my bautrate to 1200 instead of 9600.it doesn't seem to matter if I change it, it will still tell me that it will change at next reload. [code]
I have never seen this before.the command in conf t : configuration-register 0x2101 is not working, played with wr mem or copy start run neither of one useful.
View 5 Replies
View Related
Aug 22, 2012
I have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies
View Related
Jan 10, 2011
i have Router 2800 series we are using leased line Connection 8 Pubilc IP.One IP Config in Router FE0/0 IP 101.102.148.91 and FE0/1 192.168.0.0 Local IP.I have 6 Web Server. How to Config other 7 IP address on Web server in the router 2800 series.
View 6 Replies
View Related
Jul 23, 2012
I have recently made a WAN change from T1 to fiber and my Cisco 2600 series router no longer needs to connect over the Serial T1 card. The Serial connection also provided a few voice channels for the old phone system that are no longer needed. I need to keep Main Cisco 2600 router in place because I have many network devices that use it as the gateway instead of my firewall. I will not require the second subnet for Offsite Cisco 2600 anymore either. commands that will be required to remove all instances of the Serial connection and Offsite Cisco 2600. I have included the config of the Main Cisco 2600 below. [code]
View 1 Replies
View Related
Feb 21, 2011
Whenever I go to sites like godaddy.com or mydomain.com to register a personal domain, they only offer me sites like url...What can I do? Computers have lots of memory but no imagination..
View 1 Replies
View Related
Jan 31, 2012
I posted before about my problem in forwarding certain ports in a LAN-to-WAN cascaded router setup, and I finally gave up looking for a solution, and went for a LAN-to-LAN. On the internet there is many articles to be found on how to accomplish the setup, but none of them is complete, and as such, I think I really screwed up someplace. My setup: ISP modem/router (192.168.1.1 / 255.255.255.0) DHCP enabled, and DHCP address range 3-100 NAT configured Static IP address for a Synology NAS connected to the E4200 SSID id_1
Then the E4200 Internet connection type: I set to Static IP IP 192.168.1.2 Subnet mask 255.255.255.0 Default gateway: 0.0.0.0 (to disable the WAN)
Then, the network setup: Router IP: 192.168.1.2 gave me the error that WAN and LAN IPs were identical. I played around quite some time but always got an “illegal value” error. Then finally I put the IP to 192.168.0.1 (IP I had in LAN-to-WAN) and this was accepted. And subnet mask: 255.255.255.0 The SSID I left unchanged from what it was, id_2 (also gives me the advantage that I know to which router I am connected)
I rebooted the E4200, and I was connected. But … I am unable to connect to the E4200 configuration page, and even Cisco Connect cannot establish the connection.
View 9 Replies
View Related
Mar 9, 2013
Region : France
Model : TL-MR3220
Hardware Version : V2
Firmware Version :
ISP : orange
i have installed TL-MR3220 after my livebox (orange french box), my MR3220 is configurer on the DMZ zone in the livebox, internet is ok on the pc but when adsl signal is down on the livebox, the MR3220 don't switch to 3G connexion. The wan led is alway on in the router. But if i unplug the wn cable, the router switch on the 3G connexion. If i plug the wan cable the router kill 3G and use wan connexion.
How can i config my WAN config on the router for automatic switch by the router. Actually, the WAN config is fixed address (DMZ address in the livebox) Whis PPPOE id, the router can't connect. The livebox modem can't work on briddge.
View 1 Replies
View Related