Cisco Infrastructure :: Snmp For 2620 Load E1 For 2811?
Jun 20, 2012I use a cisco 2620 voice gateway with a module NM-HDV-2E1-60. Tell me how you look at snmp for Cisco 2620 load E1. For 2811, I found oid 1.3.6.1.4.1.9.10.19.1.1.4
View 4 Replies
ADVERTISEMENT
Cisco Infrastructure :: 2620 - Configuration Register Stuck At 0x3922
Sep 29, 2002I X modem an IOS file to my 2620 router and in the process set the console bps to 115200 which changed the register to 0x3922. Now when I try to connect from the console with any bps, I get garbage!
I can connect from the AUX port and get to the User Exec. mode but since no privileged password is set, I can't get any further to change the config register back to 0x2102.
Cisco :: Prime Infrastructure 1.2 Device Snmp Parameters
Jan 20, 2013I have problems with setting the snmp retry / timeout parameters for our devices. I managed to import our devices with bulk import , but after it I realized that for some devices the snmp retry / timeout values were different ( created the bulk file with 3 retries and 30 sec timeout , but in the system the appear with 2 retries and 1 sec timeout). I tried to change it manually , but after a while it goes back to the wrong values.
View 1 Replies View RelatedCisco :: NEXUS 5000 / Read CPU Load With SNMP?
Sep 18, 2011tried to read the NEXUS 5000 cpu load: cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1 but there is a timeout: Timeout: No Response from 10.100.224.16 Other MIB values readout, like the system value, is ok.We use snmpv3.
View 4 Replies View RelatedCisco :: SNMP-OID To Poll Values Of The CPU-load From VSS 6509E
Jul 4, 2012i am searching for the right SNMP-OID to poll the values of the CPU-load from a VSS (6509E)here a OID for VSS-Switch1 and a other OID for VSS-Switch2 values like cli-command "sh proc cpu" of the supervisor-module in slot 5.
View 1 Replies View RelatedCisco Infrastructure :: Temperature Status From 2960 Switch Using SNMP Not Working
Sep 18, 2012WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
Cisco Infrastructure :: Nexus 5000 SNMP - Limit Access To OIDs?
Dec 12, 2011What is the correct way to create an SNMP user on a Nexus 5k Switches and limit the read/write access to some OIDs?I have been searching for hours for configuration examples or guides, but i had no luck.I guess a role has to be created, containing rules for some feature, but the list of features doesn't contain anything about snmp.This is my configuration on catalyst switches and i'd like to achieve the same result on the Nexus 5k:
conf term
access-list 10 permit host x.x.x.x
access-list 10 deny any
snmp-server view myview ccCopyTable included
snmp-server group mygroup v3 priv read myview write myview access 10
snmp-server user myuser mygroup v3 auth md5 xxxxxx priv aes 256 xxxxxx
end
Cisco :: 7606 / 2811 - SNMP And Netflow Difference Displaying Different Data For Same Interfaces
Nov 29, 2012I've got an issue with SNMP and netflow tools. They are displaying different data for the same (sub)interfaces.I've got metroethernet link which connects root A (Cisco 7606, 12.2(18)SXF8) and root B (Cisco 2811, 12.3(11)TS). MPLS is configured on the link (behind root B there is no more MPLS). I'm attaching root configurations (I've ommited parts of config).Interfaces are:
Root A - gi2/6.2144
Root B - fa0/1
I've configured SNMP and netflow on both devices. I'm using two SNMP tools (CA Spectrum and eHealth) and two netflow tools (CA NetQoS Reporter Analyzer and Fluke Networks NetFlow Tracker) to collect the data. SNMP tools show the same info for defined (sub)interface.Netflow tools also show the same info for defined (sub)interface. I'm attaching reports from one SNMP tool and one netflow tool for the same time period.
1. Looking at SNMP tool, it can be seen quite amount of that data in both in and out direction.
2. Looking at netflow tool, it can be seen quite amount of that data in out direction, while in direction shows small amount of data.
I'm aware that Cisco has difficulties with SNMP counters on subinterfaces. I'm also aware that MPLS netflow has its own difficulties.Root B netflow configuration is quite simple as it has just 2 interfaces to configure netflow on (Fa0/0 and Fa0/1). So I would guess SNMP and netflow data should match, but they don't. When you look at SNMP tool reports for roots A and B, it can be seen that traffic volume is practically mirrored.
Cisco WAN :: 2811 DSL Load Balancing
Dec 9, 2010I have a Cisco 2811 router with two HWIC-ADSL cards configured for dsl connection. I have two lines from the same ISP and i am load balancing between them. I have created a couple of SLA's to check the state of the connections and add to the routing table the two default routes if both are up or any one of them is up.My problem is that when i try to download big files (especially antivirus updates) the download at some point stops (especially the antivirus exits with an error of unreachability). If i shut down one line everything works fine.Could i use something (configuration-wise) to prevent this problem from happening?????Is there any way i can combine the two lines? They are simple ADSL connctions with static ip's.
View 8 Replies View RelatedCisco WAN :: WAN Load Balancing On 2811
Apr 18, 2012i have a one 2811 router with 2 nos of HWIC-1FE card, and also i have two mpls connection [code] how can i configure it with mpls load balancing ?
View 10 Replies View RelatedCisco Infrastructure :: 2811 Terminal Server Configuration
Nov 30, 2011i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies View RelatedCisco Infrastructure :: Getting 2811 Router Latest Firmware?
Mar 22, 2013I need to get the latest firmware for a 2811 router but I am unable to download it. What is the best way to get hold of this can I just contact a local Cisco reseller n Monday or is it more complicated than that?
View 2 Replies View RelatedCisco Infrastructure :: 2811 Router Is Sitting Behind 3650 Switch?
Jul 9, 2012Seeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies View RelatedCisco Infrastructure :: 2811 - Router Config-register 0xC502
May 31, 2010I have Cisco 2811 Router and few days ago my router doesn't work correctly. I checked config and found config-register was changed (0xC502).
HUV_Murun#sh version
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
HUV_Murun uptime is 23 hours, 36 minutes
[code]...
Configuration register is 0xC502. What is the meaning of this config-register (0xC502) and how can be changed config ?
Cisco WAN :: 2811 - High CPU Load And Occasional Crash?
Apr 24, 20112811 router
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS_LI-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
CPU utilization for five seconds: 82%/73%; one minute: 74%; five minutes: 77% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 116 222084 57773 3844 1.83% 1.69% 1.66% 0 IP Input 183 85148 309479 275 1.03%
[Code].....
Cisco Infrastructure :: CE 1706 / PE 7206 - Multilink PPP Under Load
Apr 3, 2003Customer site connected to a PE using 2 x E1 circuits aggregated using Multilink PPP. The CE is a 1760, and the PE is a 7206. This is the customer HQ site.
Connected to the same PE are three other sites from the same customer. Each is connected with a single E1, again each CE is a 1760.
During some testing the customer did some large file transfers concurrently from each of the three remote sites into the HQ, so we had data coming into the PE via the three E1's (6Mbps) and then being routed onto the 4 Mbps Multilink PPP interface into the HQ, which is a potential bottleneck. This test failed miserably with packets being dropped on the output interface on the PE facing the HQ.
But then if Multilink PPP encap is removed, and we just connect the HQ using one E1 with HDLC encapsulation, the test works, even though we have half the bandwidth to the HQ, so an even greater potential bottleneck.
Cisco Infrastructure :: 2811 / 1841 / WIC-1AM-V2 - Setup POTS Dial Connection Between 2 Routers?
Jun 17, 2012I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
Cisco Infrastructure :: Load 2600 Router Image Which Can Fit 32 MB Flash
Oct 3, 2012I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies View RelatedCisco Switching/Routing :: 2811 With AIM-SSL2 Produces 100% CPU Load At Only 4 Mbit
Jan 15, 2012We are using a few Cisco2811's with the AIM-SSL2 hardware encryption module in a private WAN. This WAN is ethernet based and uses private address space.To add security, we are using cisco group-VPN with AES-128 encryption. The IOS version is advanced ip services.Routing is done with OSPF. According several sources on the cisco site this hardware combination should be able to handle a throughput of 30 -90 Mbit/s.In effect, we see that the CPU uses 60% at 2 Mbit/s load and almost flatlines at 100% on 4 Mbit/s load.With a 'show proc cpu' however the biggest individual process uses only 1,5%.The testscenario at which the 30 - 90 Mbit/s load get reached is a point-to-point Ipsec solution encrypted at 3DES.
View 15 Replies View RelatedCisco WAN :: How To Replace ROMmon On 2620
Jun 23, 2012I think that my rommon image has become corrupt as it will not take a new IOS image. I have tried several images that are within the recommended size and work with another 2620 with exactly the same specification also some commands that are available are not recognised when typed
View 7 Replies View RelatedCisco Switches :: 2620 DHCP Through VLAN
Jan 18, 2013I have a 2620 Cisco Router plugged into a 2924 Cisco switch by a trunk.The vlan configuration works, I subdivide my router interface with dot1q and have virtual machines on different vlans and everything works perfectly.The problem comes with a DHCP request.Let's say that I have my local lan on the native VLAN 1. I create a VLAN 25 in the switch and create a fa0/0.25 in the router.In the switch, I plug the cable modem from my ISP in a port on vlan 25In the router, I go to fa0/0.25 and issue "ip address dhcp".The DHCP request goes out, but never comes back. The problem seems to be in the switch because if I try the same thing with a virtual machine I have on a trunked VMWare ESXi server, I get the exact same results. I just don't get the IP address from the ISP.The next step would be to monitor the port on which the cable modem is connected and sniff the packets to see if the DHCP request actually gets back through.
View 2 Replies View RelatedCisco WAN :: How To Change 2620 Router To Higher Up
Jun 6, 2011We have 10M internet link and the router is 2620 we want to change it to a higher up......which one would be the best one?
View 1 Replies View RelatedCisco WAN :: 2620 - Unable To Ping DSL Modem
Nov 25, 2011I have 3 2620xm routers connected via dte/dce serial connections In a lab.One of the routers Is also connected to a 2950 switch.
The 2950 switch connects to an unmanaged tp-link switch that Is connected to a dsl modem/router.I have Internet access via the 2950 to my laptop.
I have ripv2 enabled on all the routers and It's working fine.The dsl modem, switch and connected router are on the same subnet.
When I ping the dsl modem via the 2950 or via the router connected to the 2950 , It works 100%.If I ping the 2950 from either of the other two routers , It also works 100%.I can't ping the dsl modem however from the other two routers.I've only been studying for the ICND1 so maybe there's something I'm missing here.
Cisco WAN :: 2620 - Encapsulation Dot1q Is Not Working?
Mar 26, 2012I am trying to config a 2620 Cisco router to perform subintreface (F0/0.1) for Vlan Trunk Protocol, however when I try to configure the encapsulation dot1q, I continue to receive error massage with ^ symbol below the 'c' See below, the platform version is a 12.3(26) which should be acceptable to perform an (encapsulation dot1q). The Ethernet is a fast-Ethernet 10/100 port. I also try the ISL, I receive the same massage.
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
[Code]....
Cisco :: Configuring 2620 To Cable Modem For Internet?
Aug 21, 2012configuring 2620 cisco to cable modem for internet.I'm setting up a lab to practice and am having trouble getting this to work.Made several configs that don't work and starting over form scratch.
View 3 Replies View RelatedCisco WAN :: No Link Between 2620 Router And 2950 Switch
Oct 26, 2011Can't get cisco router and switch to see each other? When I connect the 2620 router to a 2950 switch no link lights turn on. It's the same when I connect any router to either of the two 2950 switches I have. I can connect to both switch and router from a pc using telnet and the router can connect to a regular tp-link switch. I'm a newbie when It comes to Cisco. Here's the running config for the router and switch. There Is no connection when using any of the switch ports to connect to the fa0/0 of the router. [code]
View 17 Replies View RelatedCisco WAN :: 2620 Router / ASA 5505 And Qwest T1 With Ppp Encapsulation?
Mar 20, 2013I am trying to setup a cisco 2600 router that will be used to connect to a Qwest internet T1. I will have a Cisco ASA firewall behind the router so that I can build a site to site VPN tunnel. Qwest requires PPP encapsulation. The Lan side network is 10.2.0.0/16. Qwest gave me their serial IP address and my serial ip address which was I used to configure the route. The ethernet interface was configured for the local Lan side subnet and i natted both the inside and outside interface of the router. I am not sure if this is correct. How do I configure the router so that I can use one of the available public IP Addresses as the outside interface of the ASA?
Here is the config of the router:
version 12.2no parser cacheno service single-slot-reload-enableservice timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname cedar!logging rate-limit console 10 except errorsenable secret 5 xxxxxxxxxxenable password xxxxxx!ip subnet-zeroip audit notify logip audit po max-events 100no ip dhcp-client network-discoverycall rsvp-syncinterface FastEthernet0/0description Lan Interfaceip address 10.2.1.1 255.255.255.0ip nat insideno ip route-cacheno ip mroute-cachespeed autofull-duplexno mop enabled!interface Serial0/0ip address 65.121.x.x 255.255.255.252ip nat outsideencapsulation pppfair-queueservice-module t1 clock source internalservice-module t1 timeslots 1-24!ip nat inside source list 1 interface Serial0/0 overloadip classlessip route 0.0.0.0 0.0.0.0 65.121.x.x (qwest serial IP address)ip http serverip http authentication local!access-list 1 permit 0.0.0.0 255.255.0.0
Cisco WAN :: 2620 / 2950 - Serial To USB Adapter For Routers?
Jun 26, 2012I have some 2620 routers and 2950 switches that have Console Ports that are serial. However my HP PC w.Win 7 dosent have any serial ports. I am looking for a USB to Serial converter that will allow me to access the console ports so I can configure these devices. I've read many old posts and still havent found a solution. Is it true that none of these cables work? Anything that will work on XP? (also have XP PC's).How about a RJ45 to Serial?? How about a PCI Serial card? I cant believe Cisco hasnt developed a conversion cable to use with their Console Cables?
View 4 Replies View RelatedCisco Switching/Routing :: 2620 - Get New Home Lab / Configuration?
Feb 10, 2013I finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
2620 - 79xx Series VOIP Phones
Jun 10, 2012I have some 79xx series VOIP phones that are acting VERY strange ... if you are familiar with these series phones once plug them into the PoE switch they look for a TFTP server with the call manager files to acquire all the info they need to work .... i have them set up on a 2620xm router running IOS c2600-ipvoicek9-mz.124-15.T14 along with call manger 4.3. My router is my TFTP server and i have hooked up and fixed over 50 of the same series phones with out a problem.
Now here is my issue ... when you goto press the SETTINGS button on the phone you are allowed to go into the settings of the phone to change all the ROUTER,TFTP,ETC info to allow you to connect your phone to the CALL MANAGER or you can set up DHCP and it will acquire the info automatically. When i press the SETTINGS button nothing happens .... i can reset the phone to factory defaults by holding the # button then 12345678*0# then 2 not saving the info and i can hit the restart buttons which is * 6 SETTINGS buttons together and that will let me restart the phone but i cannot manually set up this phone to do anything .. it will not acquire info form my DHCP server and will not find my TFTP server at all =( the phone SETTINGS BUTTON does not respond at all ..only when restarting the phone.
Cisco Firewall :: PIX 506E With 2620 Which Type Of Cable Is Required
Sep 20, 2012I like to set up a pix and router for this network for a small buss, but I need to know what type of cable do I need to set this connection to work straight through or a cross over cable? also I need a subgestion if a nat would work better on the pix or leave it on the router?
View 4 Replies View RelatedCisco Switching/Routing :: 2650 / 2620 - Support For MPLS
Oct 29, 2011Does 2650 and 2620 support MPLS ? If yes what IOS version should i download?
View 10 Replies View RelatedCisco Switching/Routing :: 2620 NM-2FE2W Card Not Being Detected
Dec 28, 2011I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View Related
