Cisco Switching/Routing :: 2620 - Get New Home Lab / Configuration?
Feb 10, 2013
I finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
View 1 Replies
ADVERTISEMENT
Jan 7, 2012
I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies
View Related
Oct 29, 2011
Does 2650 and 2620 support MPLS ? If yes what IOS version should i download?
View 10 Replies
View Related
Dec 28, 2011
I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies
View Related
Nov 10, 2011
Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies
View Related
Jan 10, 2012
Which WIC or NM Ethernet card is compatible with a 2620, (non XM) router? I have seen conflicting information on compatibility. I am wanting to connect this router via an Ethernet Port with a non Cisco router that is connected to my ISP.
View 1 Replies
View Related
Aug 25, 2012
I am trying to create a backup of my 2620 router so I can use for GNS3.
I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection
I have made no other configurations on this router, everything else is default.
I can successfully PING from both ends
**PROBLEM: My problem is that when trying to 'copy flash' to my TFTP server, the response is**
".....
%Error opening tftp://192.168.1.3/c2600-advsecurityk9-mz.124-1a.bin (Timed out)
Router"
Is there another setting I should enable? Remember I have made no other configurations bar the ones above.
View 1 Replies
View Related
Jul 9, 2012
My configuration is the following
Router ISP >>> Switch 2940 >>> Router 2620 >>> Host (Tacking dhcp from my 2620)
I got servers and other switches 2950 working perfect from the 2940....but the 2620 or even a Switch 3550 (in router L3 port), has the same issue...do not share connection with Host's behind them, I got IP on the host, pinging the Fa0/1 (dhcp), pinging the Fa0/0, but cannot ping the GATEWAY and not surf the internet.
View 3 Replies
View Related
Jan 12, 2013
I am new to Cisco networking (I just passed my A+ test and am working on my Network + test with an end goal to finish with a CCNP) and I bought a Cisco 2620 XM and a 1605R to figure out how to setup and practice on. In my house we have Verizon Fios with the standard Verizon appliance feeding internet to the rest of the house. My question is that will my Cisco appliances be usable with an out connection from the Verizon appliance? I am concerned because the connection that comes into my room from the Verizon router would be considered a LAN connection, not a WAN? Also in order to configure the router, I believe it needs an RJ-45 to serial to plug into a computer for setting up. My computer doesn't have a serial port so will an RJ-45 to USB work (since that is serial as well)?
View 3 Replies
View Related
Jan 27, 2013
I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
View 2 Replies
View Related
Sep 29, 2002
I X modem an IOS file to my 2620 router and in the process set the console bps to 115200 which changed the register to 0x3922. Now when I try to connect from the console with any bps, I get garbage!
I can connect from the AUX port and get to the User Exec. mode but since no privileged password is set, I can't get any further to change the config register back to 0x2102.
View 6 Replies
View Related
Nov 25, 2011
I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
View 5 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Mar 4, 2012
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
View 7 Replies
View Related
Jan 18, 2013
Why does mine show this and NOT all 4 ports and 1 wan port?
Manases#sh verCisco Internetwork Operating System SoftwareIOS (tm) C831 Software (C831-K9O3SY6-M), Version 12.3(2)XA7 [code]...
How do I make it show all my ports? when I plug in something to port 1-4 it shows me on the log that I plug in to e0. I got port1-4 and 1 wan port.
View 8 Replies
View Related
Mar 8, 2012
I was recently given a PIX 501 router. I am very new to the world of Cisco, but want to learn. I got a few things setup on the router but, am not sure how to get it to use my DSL connection. My DSL modem IP is 192.168.2.1. Below is my router config. What more do I need to do? Also, is the outside IP not the IP of the DSL modem?
PIX Version 6.3(1)
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
[Code]...
View 1 Replies
View Related
Jan 31, 2013
Trying to configure an 891-W on my home network.
Basic TW cable modem ---> 891-W with DHCP I have done the following and are getting an IP address but no internet. I have FE8 set as DHCP and VLAN1 as 192.168.1.1 255.255.255.0
I originally thought that "WAN GE 0" would be connected via my modem but I had no luck there either so I set FE8 as WAN?
Building configuration...
Current configuration : 2907 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
View 28 Replies
View Related
Apr 6, 2012
i have a cisco router 887 which i am trying to configure. but however, do i really need to use the SDM utility or i can do it through CLI?i need to replace my current router in my small home office.
View 3 Replies
View Related
Mar 17, 2012
i have the asa5505. the configuration of asa 5505 is:
: Saved
Code...
i analyzed this traffic i see problem with the nat- Asymmetric NAT rules matched for forward and reverse flows. where i made error?
View 0 Replies
View Related
Mar 15, 2012
how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?
View 1 Replies
View Related
Mar 19, 2012
i have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies
View Related
Feb 13, 2013
I have been using a Cisco 877 to connect to BT broadband and it was working fantastically with no issues. For reasons outwith my control we have moved to 02 and I cannot get the cisco router to connect (the supplied router works fine). O2 support is limited as they say they will not assist in the config of third party routers but they have supplied the below (the line has a static IP). I have also included my current config which was working fine with BT. I have attempted to write in the updated info but have been unable to get the line to connect. [code]
View 6 Replies
View Related
Jan 12, 2013
i have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
View 5 Replies
View Related
Nov 28, 2012
I have a network behind an 861 and users are unable to access e-mail from the local exchange server from their iPads using the 802.11wireless network. The wilrelss network is working fine and the iPad users connect fine.I was told that that i need to configure "hairpin DNS".
View 2 Replies
View Related
May 2, 2012
Any configuration example to build a vpc b/w 5ks and 7ks? i have total 4 links between them . If not, I am assuming to have the following config for the port-channels:- (Provided the vpc domain is configured).
N5k1 and 2:
int eth1/10-11
channel-group 10 mode active
switchport mode trunk
int po10
switchport mode trunk
switchport trunk allowed vlan a-d
[code]....
So, its basically vpc 10 that has 4 physical links b/w the vpc domain of 7ks and vpc domain of 5ks.
View 3 Replies
View Related
Dec 27, 2012
I'm currently trying to get up to speed on a 1941W ISR. I belive i have most of the configuration correct based on reading the documents on this site. However, i'm noticing that my lan to lan network performance is very slow. Peaking out about 3mbs. I was reading some documentation that suggested MGF (MultiGigabit Fabric) might resolve this problem.
I have a basic setup in my test environment trying to emulate a branch deployment. 1941W connected to a access switch (3400).
- I'm getting slow perfomance (thoughput) between the vlans 66,30,10. Will MGF fix this problem? How do i configure it?
Building configuration...
Current configuration : 7474 bytes
!
! Last configuration change at 09:26:04 PCTime Fri Dec 28 2012 by xxx
! NVRAM config last updated at 09:26:05 PCTime Fri Dec 28 2012 by xxx
[Code]......
View 4 Replies
View Related
Feb 21, 2012
We recently switched a faulty N5548UP with a replacement and everything went fine, with the exception of one minor thing.
We're currently unable to authenticate using tacacs+.
When trying to enter the command 'aaa authentication login default group [groupname]', the following msg appears: too big pss key or value size could not update aaa configuration
We're running 5.0(3)N2(2b).
View 3 Replies
View Related
Jul 17, 2012
I currently work in the IT field part-time as a end-user support technician while I am finishing my Bachelor's Degree in Network Administration. I'm not completely new to networking at this point, but I am by no means a master of it either. The basics of small networks (less than 10 PCs) and the lower-end of small business grade Cisco equipment are not unfamiliar to me. Up until this point however, I have had very little experience with any higher-end Cisco networking equipment.
Now on to the questions, which may seem like the answers should be obvious, but let's face it, I do not have the resources to own much equipment myself at this time for experimentation purposes, nor does the school I am attending have a lot of financial resources to provide us with recent hardware to learn on. What I want to know are a few things about PoE as implemented on Cisco devices, specifically the SG200-50P small business series switch. According to the technical documentation, the switch supports PoE on 24 of its 48 ports, specifically 1 - 12 and 24 - 36; simple enough. The switch is currently installed in an office that has less than 24 connected devices, but that is currently expanding. None of the PoE ports are utilized as of yet, but going forward, there will be more than 24 connected devices. Will another switch need to be installed if the additional connected devices (PCs and printers) are not using PoE, or is the PoE an auto-sensing feature that will simply remain disabled if a device that does not require power over the network cable is connected? Is there some setting that needs to be changed through the management interface to keep devices that should not be drawing power from doing so?
There will likely be some additional questions generated by my inquiry, and I fully understand if these are completely novice questions, but I admittedly do not know the answer. When I Googled it, I was greeted by a few hundred thousand results, the first dozen or so pages of results all being for places to purchase this particular type of switch, so I thought I would try my luck on the forums of the place that made it.
View 1 Replies
View Related
Jan 9, 2013
On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
View 3 Replies
View Related
Sep 28, 2012
I am trying to configure a 891 W to basically provide DNS from my ISP to my internal clients on the 891 W. Currently when I am on a PC I can see that I receive my IP information along with the correct ISP DNS IPs. However when I try to connect or resolve a URL it fails. Nor can I perform an ns lookup from the cli of the 891 W. I seem to be having a translation issue with DNS.
View 2 Replies
View Related
Jan 18, 2012
I have asked to test an VPN phone for home Users. I have a BT adsl broadband at home which is going into a cisco 2900 switch. Port One is connect to the computer port 3 is connected to the Avaya VPN phone this work's. The quality is not very good, so the question is could I have qos on Port 3 which is connected to the phone?
View 4 Replies
View Related
Jun 25, 2012
I'm trying to install a Gateway in Red Hat Linux to Cisco Smart Call Home Service, and reading about this in google, i find this info:Smart Call Home on the ASA This is much more simply to configure and operate.I want to know what solution is more recomended and why.
View 1 Replies
View Related
