Cisco Switching/Routing :: 2620 XM / 1605 R - Compatibility With Verizon Appliance
Jan 12, 2013
I am new to Cisco networking (I just passed my A+ test and am working on my Network + test with an end goal to finish with a CCNP) and I bought a Cisco 2620 XM and a 1605R to figure out how to setup and practice on. In my house we have Verizon Fios with the standard Verizon appliance feeding internet to the rest of the house. My question is that will my Cisco appliances be usable with an out connection from the Verizon appliance? I am concerned because the connection that comes into my room from the Verizon router would be considered a LAN connection, not a WAN? Also in order to configure the router, I believe it needs an RJ-45 to serial to plug into a computer for setting up. My computer doesn't have a serial port so will an RJ-45 to USB work (since that is serial as well)?
View 3 Replies
ADVERTISEMENT
Jan 7, 2012
I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies
View Related
Feb 10, 2013
I finally decided to get my own home lab so that I can configure to my hearts' content and not have to wait for access at the school to do it. I have three 2620 routers inter-connected with wic2t cards, and five 2950 switches. I have already set the config reg. on the routers to 0x2102 so that I can save my configs when I power down. When I pulled up the config regs on the switches, they all had 0xf as the reg number. Is this a good config reg number to have if I want to save the config before I power down?
Also, what would be a good ios version to have running on the switches and also the routers? I have access to other cisco IOS' but I want to double check. With this setup I would practice bgp, ppp, frame relay, rip2, ospf,eigrp, stp, pvst,pvst+, Rapid pvst+, rstp, and mstp.
View 1 Replies
View Related
Oct 29, 2011
Does 2650 and 2620 support MPLS ? If yes what IOS version should i download?
View 10 Replies
View Related
Dec 28, 2011
I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies
View Related
Nov 10, 2011
Need to know if i can add 1 FE card to 2650XM or 2620 Routers.i know we can add Ethernet card but it is only 10MB .
View 2 Replies
View Related
Jan 10, 2012
Which WIC or NM Ethernet card is compatible with a 2620, (non XM) router? I have seen conflicting information on compatibility. I am wanting to connect this router via an Ethernet Port with a non Cisco router that is connected to my ISP.
View 1 Replies
View Related
Aug 25, 2012
I am trying to create a backup of my 2620 router so I can use for GNS3.
I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection
I have made no other configurations on this router, everything else is default.
I can successfully PING from both ends
**PROBLEM: My problem is that when trying to 'copy flash' to my TFTP server, the response is**
".....
%Error opening tftp://192.168.1.3/c2600-advsecurityk9-mz.124-1a.bin (Timed out)
Router"
Is there another setting I should enable? Remember I have made no other configurations bar the ones above.
View 1 Replies
View Related
Jul 9, 2012
My configuration is the following
Router ISP >>> Switch 2940 >>> Router 2620 >>> Host (Tacking dhcp from my 2620)
I got servers and other switches 2950 working perfect from the 2940....but the 2620 or even a Switch 3550 (in router L3 port), has the same issue...do not share connection with Host's behind them, I got IP on the host, pinging the Fa0/1 (dhcp), pinging the Fa0/0, but cannot ping the GATEWAY and not surf the internet.
View 3 Replies
View Related
Jan 27, 2013
I have a lab setup to take my CCNA and CCNP and I'm having issues trying to get WAN connectivity back to a switch at the end of my network. My lab environment consists of 1 - 2950 switch, 1 - 2620 and 1 - 2621XM. I have 1 Ethernet connection from each router to the switch and 1 serial connection from the 2620 to the 2621XM. I have the serial interfaces in a shutdown state right now so there is no loop since I do not have Spanning tree setup on the ports on the switch yet.
Right now using the fast ethernet ports on the routers and I have no issues its when I shut down those Ethernet ports and try using the serial interfaces when I start having issues. So my network layout is Ethernet from switch port f0/4 to port f0/0 on 2620 and serial from s0/1 on the 2620 to s0/2 on the 2621XM. My 2621XM f0/1 is whats connected to the WAN and I have no issues getting to the WAN from my 2621Xm or my 2620 but when I try pinging any website or even my WAN default gateway from my switch I get nothing!
Ive also noticed that when I do a IP NAT translation (after accessing the WAN from my 2620) on my 2621XM the source IP is of my serial connection not the ip of my 2620 router? I have my default gateway on the 2620 as the the IP of my serial interface on the 2621XM and vice versa because my LAN network is 172.16.1.0 and my WAN is 172.16.9.0. I have a /31 setup between my serial connections 172.16.11.0 (s0/1) is on the 2620 and 172.16.11.1(s0/2) is on the 2621XM. I used the SDM (ver 2.5) to setup NAT to have f0/1 with Nat outside and s0/2 as Nat inside. Encapsulation is HDLC between the serial links. Ive attached the running configs of the switch and routers.
View 2 Replies
View Related
Nov 25, 2011
I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
View 5 Replies
View Related
Jun 13, 2012
Are 887VAM-W-E-K9 and 800-IL-PM2 compatible? We have got both of them but it seems that router has a 30W power source and module has a 80W power source.
View 1 Replies
View Related
May 13, 2013
I have a WS-X6748-GE-TX with the WS-F6700-CFC daughter card. Is it possible to replace the WS-F6700-CFC daughter card with a WS-F6K-DFC4-AXL to make this compatible with the SUP-2T? Or, are there differences between the CFC and DFC base modules?
View 11 Replies
View Related
Sep 1, 2012
We have connected a single F5 box with dual links to 2 different Cisco Catalyst switches using 802.1Q trunks. F5 is configured with RSTP mode and on Cisco Switch RPVST+ is configured.STP root bridge is hardcoded on the Cisco side. Loop Guard is globally enabled.On F5 STP link type is Auto, STP Edge port is disabled since that port is connected to the cisco switch.When we are failing over the F5 primary link to the secondary link we see 'Loop Inconsistent' on the cisco switch and things dont work after the failover.We have tried configuring the F5 as STP passthrough but that doesn't fix out the issue.I have checked out the forums and found out following recommendations
1. Configuring MSTP bw F5 and Cisco for better compatibility (Not possible from Cisco side because of a major change in large production setup)
2. Configuring VSS in Cisco switches (not possible due to hardware limitation)
3. Connecting F5 using single links to each switch (redundancy compromised)
I am wondering that on which default vlan does the F5 STP instance0 sends the STP BPDUs ? the term used on Cisco side is native vlan and others use PVIDs; that F5 default vlan should match the native vlan on cisco trunk side.
View 2 Replies
View Related
May 31, 2012
we have to upgrade to nxos 5.2(4) but i cannot find same image for epld , i only see a downlable image with version 5.2(3). Do you see any problem if we upgrade kick and system image to 5.2(4) with epld 5.2(3)?
View 3 Replies
View Related
May 27, 2012
The below nexus 5020 nx-os version and type/revision of my GLC-T is compatible with each other? I noticed also the "Transceiver calibration is invalid" when i do show int e1/8 transceiver details , what does it mean?
View 8 Replies
View Related
Oct 22, 2012
I've inherited a network. It looks to have been setup as 10/100 originally, using Netgear FSM726S switches with fibre connecting the switches. The fibre to copper conversion is mainly achieved with 10/100 media convertors rather than GBICs - not sure why - though there are some GBICs in use. Some of the "key" switches have been upgraded to Cisco Catalyst 2960G switches, but nothing else has been touched, so most of the network still runs at 100MB.
View 1 Replies
View Related
Feb 7, 2012
We are upgrading two standalone 6509E chassis to a VSS system with new VS-S720-10G-3C cards. The 6509's have WS-X6748-GE-TX card with DFC3B daughter cards (see below). The compatablity matrix (see below) states that 67xx cards are supported but it goes on to state DFC3C or DFC3CXL cards are needed. So does this mean that the existing WS-X6748-GE-TX cards have to be upgraded or will they be supported?
Core #1Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP SAL 2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAD 5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL 6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL 7 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL 8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL
[code]....
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Dec 18, 2011
Can a WS-C3750X-12S coexist in an existing stack made up of a WS-C3750G-12S and a WS-C3750G-24TS?
View 7 Replies
View Related
Feb 4, 2012
I have a Cisco 3825 router with a sfp module .(multi mode Cisco sfp ) connected to a Alcatel switch with fiberxon sfp. On a Cisco router the sfp card is been recognized and is seen when i used " show ip int brief " or show inventory commands. However the line protocol is down.
is their any compatibility issue with one side Cisco sfp and other side fiberxon sfp ? we have tested Cisco sfp -------Cisco sfp works fiberxon ----------------fiberxon works .
View 3 Replies
View Related
May 7, 2012
Currently i've a cisco ws-c4506-e edge swith loaded with cat4500e-ipbasek9-mz.122-53.SG4.bin image file. Can i use this image file on a ws-c4503-e as well?
View 1 Replies
View Related
Mar 25, 2012
I would like to confirm if Cisco 3750 and 3750v2 can work in a stack? My Cisco 3750 is working on 12.2(37)se while 3750v2 is working on 12.2(50r)se.
I tried to configure the above on a same stack but seem to have compatibility issue and fail to work.
View 3 Replies
View Related
Mar 13, 2011
We have existing stack of 3 units of WS-C3750-48TS-S ( 100 mbps ports with Gigabot uplinks). with IOS as follows, Can we add WS-C3750G-48PS-S in this same stack (this is 48 Gigabit ports)?
View 2 Replies
View Related
Mar 5, 2012
Is the C3KX-PWR-1100WAC= compatible with the WS-C3750X-24P-S?
View 1 Replies
View Related
Jan 31, 2012
I am looking to see if Nexus 5596UP & Nexus 2248TP GE compatible with SFP-10G-SR? The reason is because a consultant was hired on to "design" the network layout and has decided to purchase Cisco SFP+ Copper Twinax Cables which have a 10M limit. A small handful of the Data Center racks are 10-15M away... just out of reach of the Twinax. I would prefer NOT to move the LAN row so that it is more centered in the room. Can I use the SFP-10G-SR to connect the 2 switches (5596 & 2248) together? This SFP has a 26M reach on standard 10gig fiber, the small cost increase per connection is of no concern.
View 2 Replies
View Related
Jun 4, 2012
I am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies
View Related
Jan 9, 2012
Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
View 5 Replies
View Related
Mar 28, 2012
Will a WS-X6748-GE-TX work with a Sup 32 in a 6506/6509?
View 2 Replies
View Related
Jun 12, 2012
My old switch software version is c3750-ipbase-mz.122-35.SE5 and model number is WS-C3750-48TS-S and my new switch Software version is c3750-ipservicesk9-mz.122-50.SE5.bin and model number is WS-C3750V2 . I want a compatible (prefer same) version of IOS which works on both the switches as both the switch will be in a stack..
View 4 Replies
View Related
May 22, 2013
I have Cisco Access point AIR-CAP1602I-N-K9 ,My doubt is,is this AP support on WLC AIR-WLC2112-K9
View 1 Replies
View Related
Apr 14, 2013
I wanted to know that in nexus 7009, can i use mix of F2/M1/M2 series line cards ? will they work with each other ? Lets say i have F2 line card and M2 line card, will servers attached to them will communicate with each other ?
View 4 Replies
View Related
Sep 12, 2012
I have a Cisco 3560 connected via fiber to a Nortel 1612G. The connection is up/up, the V LAN's on the switch work as needed, but I can not ping the switch from the Nortel, and as a result I can not remote into the Cisco for management. I see in the configuration for the trunk that it is configured for a native v LAN, but I don't see it defined which v LAN's are allowed, could this be the issue? I will provide some of the config information for the Cisco side, I understand the issue may be on the Nortel end but if the Cisco part looks OK?
Port config for the trunk:
interface GigabitEthernet0/49
description port_6_1612G
switch port trunk encapsulation dot1q
switch port trunk native v LAN 120
switch port mode trunk
Native v LAN config:
interface Vlan120ip address 172.16.120.11 255.255.255.128
View 3 Replies
View Related
