Cisco Switching/Routing :: 3560 / Nortel 1612G - Compatibility Between Two Switches
Sep 12, 2012
I have a Cisco 3560 connected via fiber to a Nortel 1612G. The connection is up/up, the V LAN's on the switch work as needed, but I can not ping the switch from the Nortel, and as a result I can not remote into the Cisco for management. I see in the configuration for the trunk that it is configured for a native v LAN, but I don't see it defined which v LAN's are allowed, could this be the issue? I will provide some of the config information for the Cisco side, I understand the issue may be on the Nortel end but if the Cisco part looks OK?
Port config for the trunk:
interface GigabitEthernet0/49
description port_6_1612G
switch port trunk encapsulation dot1q
switch port trunk native v LAN 120
switch port mode trunk
Native v LAN config:
interface Vlan120ip address 172.16.120.11 255.255.255.128
View 3 Replies
ADVERTISEMENT
Nov 2, 2011
Connecting a legacy Nortel switch (425/450/470/BPS) to a Nexus 7000 via gigabit fiber? I have a customer trying to do it and they say that the connection never comes up. The support on the Nortel stuff is long since expired, so Avaya is not being particularly useful. Apparently Cisco says the issue is "fast link pulse to the BayStack to determine the capabilities of the uplink and the BayStack is returning all zeros." I have not verified this and actually have not yet gotten my hands on the Nexus side of things
View 2 Replies
View Related
Dec 6, 2011
Is it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
View 2 Replies
View Related
Jul 22, 2012
Was building a small network in Cisco Packet Tracer and ran in to an issue. I have 4 routers running OSPF, and off one of the routers I have 5 3560 Multilayer switches. The router that the switches hang off of, I have a sub-interface with dot1q encapsulation, set for vlan 10 and an IP Address. 10.14.16.1/24. The switches have interface vlan 10 configures, and have IPs in the same subnet. From that router, I can ping/telnet to all the switches without issue. My problem arises when I try and reach those switches from any other router. OSPF is set to redistribute static and connected subnets.The routing table is populated correctly on all the routers. When I ping and trace the packet, it looks like it makes it all the way to the respective switch, but the packet never makes it back. I've played with the default route on the switches to no avail. Am I trying to implement this incorrectly, or am I just missing something?
View 4 Replies
View Related
Sep 5, 2012
whether VSS technology support on 3560 switches.I'm planning to intergrate new Cisco 2x6509 with VSS and all the access swtiches 3560's uplink to core 6509..if not support, what will be the solution or any bug fixing or new IOS releasing
View 1 Replies
View Related
Sep 9, 2012
In cisco documentation for the 3560 it is mentioned that blocking appletalk will not work .It shows up in command line but it is not working due to hardware limitation.Is there any other way to block appletalk on 3560 swiitches.
View 3 Replies
View Related
Apr 24, 2012
I have a question about RSPAN, is this feature only supported on 6500 and 4500 switchs?
we have 2 3560 switches and want to use RSPAN to monitor different source ports.I checked thorugh the cisco feature navigator and the IOS we have on 3560 has the RSPAN fature listed in them.
View 2 Replies
View Related
Jul 16, 2012
OSPF normally only comes with IPservices image and not IP Base image. The 3560-C series data sheet says that it only suport IP Base image, yet it mentions that support for OSPF in included. Are there any restictions in the OSPF support?.
View 7 Replies
View Related
Sep 3, 2012
I have a 5K with 5 downstream 3560's. I now have a new 5k that I would like to add to the existing 5K as a HA peer. What is the best way to accomplish this with the least amount of downtime for the downstream switches.On the 3560's, i plan setting up port-channels once HA is setup on the 5k's.
View 1 Replies
View Related
Sep 21, 2012
We have 7 3560's in 7 different locations connected to our providor for wan access. Our provider has given us a copper cable at each point and we have connected it directly to our 3560 switch at each location. Each port is configured the same way at each location. Each switch is running eigrp.All of the switch ports on each switch are configured as a trunk and vlan 299 had the ip address for the eigrp connection: [code] This setup is working as each switch see's all of the other switches as an eigrp neighbor. We have also made sure that the switch at our head office has spanning tree priority for vlan 299.
So the problem is, if there is a change in the topology at one of the locations it usually causes one or more of the other connections to go down for some reason. We just cannot pinpoint what is causing this change. There are no log's or anything other than an eigrp hold time expired message.?
View 9 Replies
View Related
Feb 19, 2013
We have a couple of Cisco switches and connected a (Windows 7) laptop to one of them and it gets its IP address from a DHCP server.I can now ping the IP from all of the switches, no problem, also not when I log on to the core switch in the same VLAN as both notebooks. But from my (Windows 7) laptop, which is in the same VLAN as the target laptop, I cannot ping it.
I checked, default gateway is good on both sides, as are DNS servers.
Target notebook ---- Catalyst 3560 V2 switch === Core Catalyst 3750 switch (stack) === Catalyst 3560G switch --- My notebook
View 4 Replies
View Related
Jul 9, 2012
For some special arrangement, I would like to connect 2 access ports from a 3550 switch to 3560 switch.1 port for vlan 200, another port for vlan 201.Will this introduce bad thing to the switches?
View 4 Replies
View Related
Apr 25, 2012
I have a connection between switches, There are a 3560 (Gi0/37) and a 2960 (Gi0/1), the problem is in the port Gi0/37 of the 3560 switch and this is the log. [code]
I dont understand what is the problem, actually i have added the command power inline never on the port and the problem is solved, but we haven´t changed configuration.
View 3 Replies
View Related
Jun 3, 2012
We have two Cisco switches with one 3560 and one 3750 we have created a new Vlan 4 with IP 10.1.3.x 255.255.255.0 - no shut then assigne to gi 2/0/46 on the 3560 Vlan 4 ip address 10.1.3.x 255.255.255.0 no shut then assign to FA0/45. All interfaces are up up along with the Vlan up up, we can ping the local IP address bu not able to pint the other switch.
View 2 Replies
View Related
Jan 16, 2013
We are in the process of rolling out iPads to our offices. As part of this implementation, we need to print from the iPads to our network printers. Our network printers are mostly HP and Xerox and do not have native Apple AirPrint capabilities. As such, we have been using the FingerPrint software to share out the network printers as Apple AirPrint printers. We have a mixture of switches at our offices. Most offices utilize a 3550 PoE switch. In these offices the AirPrint traffic is being transferred successfully and everything works great. In the offices which are using 3560 PoE switches, the traffic is never seen at the iPads. We are using EnGenius EAP300 access points connected into the Cisco switches to provide wireless access to the iPads. Both 3550 and 3560 switches are running iOS 12.2(25). What might be stopping/blocking the AirPrint traffic on the 3560 switches?
View 3 Replies
View Related
Nov 7, 2012
I have a couple of 3560 switches running c3560-advipservicesk9-mz.122-44 and they are randomly experiencing the following:
- The switch locks up with no preceding error message in the log (I am forwarding syslog to Splunk).
- Upon reboot, the switch goes through the normal startup sequence with no error messages, then for some reason reloads the flash and starts all over again. (refer to doc)
This could happen after days or weeks. Sometimes they will go through two of these reloads on boot and be fine for awhile, and other times they will be stuck in the loop infinitely. I am using this same image with all of our 3560s, but am only having this issue with two of them.
View 2 Replies
View Related
Jul 15, 2012
I have 3 3560 switches which are configured with trunks between them. They run vlan 10, 11 & 12. I have a 'core' switch (switch 1) of these 3 to which an MPLS router is connected on vlan12. I in addition have another switch hanging off the 'core' switch via a routed link (switch 4). I have EIGRP configured as a stub and as such the IP address on the routed link at the core switch end is of a /24 from v lan 1 on the other switch. This makes the route directly connected and therefore distributed via EIGRP stubs. Switch 1 is then exchanging routes with the MPLS router (via EIGRP).
The problem I have is that from any sub net on any switch (switch 1, 2 or 3) I can ping 192.168.13.1 (switch 4). When I try and ping switch 4 from over the MPLS I am unable to. If I trace to the switch I see it reaches the outside of the MPLS router, but is then unresponsive. The same applies if I try to ping switch 1 on 192.168.13.2. Any of the other IP addresses of switch 1 respond.
The MPLS network is a managed solution to which I have no access. I'm told that the MPLS provider is able to ping switch 1 & switch 4 on the 192.168.13.x addresses from a remote router (192.168.32.2). I have tried from a switch on the same L2 sub net (192.168.32.1) and I don't get a response.
From switch 4 I am able to ping the switch on 1 of it's interfaces (192.168.19.1), but not the interface I mentioned above 192.168.32.1. There are no access lists in place on the switches and no firewalls between the sites.
View 22 Replies
View Related
Feb 5, 2013
I have 3560's in my current environment, operating in the core/distro/access layers. The switches are in a star configuration, performs only layer 2 switching, and utilizes copper (no plans on moving to fiber).
With a fairly limited budget, I've been contemplating on upgrading the central node to a stacked 3750X to eliminate that single point of failure, and trunk the rest of the 3560's to the stacked switch. I wanted to be sure that the 3750X switches will be right for my environment (90-100 hosts), and if what I explained above is a good solution.
I'm also looking like to upgrade 6-7 of my servers (and SAN) with 10GB network cards. Do the ports on the 3750X have port densities capable of 10GB? If not, what switches provide that capability?
View 10 Replies
View Related
Feb 20, 2013
I need to support a bunch of security cameras mounted on poles in our parking lot and an IP intercom system mounted on some gates. Because of environmental factors the switches at the poles need to be hardened and the spec from the vendor installing the gear is for GarretCom Industrial unmanaged switches which would make sense.
However when Information Security got wind of this scheme they (probably correctly) are requiring me to secure the ports that these unmanaged switches connect to. I have 2 choices: port security w/ MAC filtering or 802.1x. Because all the devices at the poles and gates support 802.1x and because I may need to go out there to troubleshoot stuff (and will invariably forget to add the MAC of whatever device I am using) I would prefer 802.1X multi-auth mode.
Problem:
When I ran a quick test on a test 3560 running some 15.0.1 code I could get a laptop to connect via 802.1x EAP-TLS successfully if it was directly connected but when I connected the same laptop via a dumb Netgear switch I confiscated from a luser it would not connect. The 3560 error said that the laptop never responded.
Question:
Before I spend a whole lot of time on this, is this something that should work? I don't see any practical use for the feature if it won't however the documentation I am using specifically mentions downstream hubs but I am not sure if they mean real hubs (which I don't think are even made anymore) or if they mean unmanaged switches.
I plan to try a couple of different unmanaged switches tomorrow and digg a little but I would like to know if I am wasting my time on something that will never work or if there is a little gotcha somewhere.
View 2 Replies
View Related
May 10, 2012
Does a portable RPS device either from Cisco or another manufacturer exists, that would allow you to move primary power for a switch without causing an outage? I realize that for the Catalyst 3560 for example, you can get an RPS 2300 or 675, but my understanding is that these are made for a more permanent installation, not to mention rather costly.
It looks like the RPS 675 is rather inexpensive after all, especially in the secondary market, but still rather large for toting around.
View 1 Replies
View Related
May 24, 2012
If the ports on a 5508 can only perform etherchannel(no LACP or PAGP), only on mode, how does a 5508 create a bundle with a nortel switch?
View 1 Replies
View Related
Mar 26, 2013
We have 2 x Nortel 8600s (now Avaya) that are 6-7 years old. They have 96 1GB ports on each and we only use about 30 and the CPU average is around 2% and memory is 40% (256mb). Going into 8600s we have 8 x Nortel 5520 48port gig switches.
We want to replace the 8600s at some point and I wondered roughly what Cisco device would possible suit us. We are not after the best high end switches that we will never utilise, but ones that will aid us grow for the next 5 years.
View 16 Replies
View Related
Dec 12, 2011
Is there a chart to show what modules will fit what swithches for fiber applications ex 2950 and 3560 switches
View 1 Replies
View Related
Jan 18, 2012
We have 3 Nortel RG 9150 remote PBXs installed at a branch location, and they have been functioning well for years plugged into 3Com 4500 10/100 switches. These switches have a very basic configuration; nothing special. We are transitioning over to Cisco 2960 switches with very basic configurations. The problem is that when we plug the 9150 into the 2960 switch, the RX light flashes like it should, but the TX light only flickers intermittently. We cannot ping it from the switch or local router. Everything in this building is in VLAN 1. I've tried turning on full duplex on the 9150 and/or hard-setting the speed/duplex on the 2960 switch. The company that maintains our 9150 sent a guy out who was completely puzzled by this too. In some ways this seems too basic to be a problem, but it is. The twist on this problem is that the 3Com switch, which the 9150s are plugged into, is connected directly into the Cisco 2960 that I can't make them work on. Plug them into the 3Com, they work; move them upstream to the Cisco, and they stop, even after I reboot them.
Here are the port configs of the 3Com and Cisco switches.
Cisco
interface FastEthernet0/15
switchport mode access
[Code].....
View 15 Replies
View Related
Aug 19, 2012
I have a customer that wants to change their Nortel 5520 switches to a Cisco solution, and I wanted to ask what would be a good solution for this customer. presently they have 4 48 port PoE and 2 24 port PoE stackable 5520, and they are interested in redundant power supplies for the switches. I was thinking that the 3750 is good for this site.
View 4 Replies
View Related
Jun 6, 2012
I've just completed a port security project at a site on numerous Cisco switches and all works well, however they have 2 Nortel 5520 switches (which I left until the end) which they would like to lock down. I have logged a message on the Nortel forums and I have heard nothing for days. I just need to lock 2 ports down to the Mac address of 2 computers stopping any other computer being plugged in.
View 2 Replies
View Related
Jan 10, 2013
I've been fighting what seems to be an increased number of outqueue drops on our core stack and edge switches for the last 3 or 4 weeks.(The core consists of a stack of 5 3750s in 32-gig stack mode. The wkgrp switches are 3560s. all are at 12.2.52) The wkgrp switches are directly connected to users. We use Nortel IP phones with the phone inline with the user PC. auto-neg to 100/full. [code] However I have tried turning off QOS on a couple of workgroup switches (no mls qos, but left individual port configurations the same) but am still seeing drops.Since I have disabled qos on the switches in question (no mls qos) (not the core tho) I am presuming these commands have no affect on the switch operation and therefore cannot be related to the problem. With QOS turned off one would presume that it is general congestion - especially at the user edge where busy PC issues might contribute. So I wanted to see if I could see any instances of packets in the output queues building up.
I wrote some scripts and macros that essentially did a snapshot of 'show int' every 20 seconds or so, and looked for instances of 'Queue: x/' where x was greater than zero.What I found after several days of watching the core stack, and a few of the workgroup switches that are most often displaying the behavior, was that I NEVER saw ANY packets in output queues. I often saw packets in Input queues for VLAN1, once in a great while I would see packets on input queues for fa or Gi interfaces, but NEVER on output queues. [ code] Additionally, when I look (via snmp) at interface utilization on interfaces showing queue drops (both core and wkgroup), they are occurring at ridiculously low utilization levels (as low as 4 to 8%). I've tried to look for microbursts between the core and a wkgroup switch where the core interface was experiencing drops, but haven't seen any (using observer suite). [code] While the queue-drop counts aren't critically high at this point, they are happening more frequently than in the past and I would like to understand what is going on... In most cases, no error counters are incrementing for these interfaces. Is there some mechanism besides congestion that could cause output queue drops?
View 4 Replies
View Related
Oct 7, 2012
I just trying to setup a dhcp server in my catalyst 3560 switch for a nortel ip phones. I show you mmy configuration:
VOICE VLAN: 3
DATA VLAN: 1
S1:10.2.110.200
port:4100
Nortel IP Phones: IP 2002 (Firmware Version 0604D9H) & IP 1110 (Firmware Version 0623C7)
Switch Configuration:
aaa new-model!aaa session-id commonip subnet-zeroip routing!ip dhcp pool datos network 10.2.100.0 255.255.255.0 default-router 10.2.100.1 lease 0 2!ip dhcp pool voice network 10.2.110.0 255.255.255.0 default-router 10.2.110.200 option 191 ascii "VLAN-A:3" option 128 ascii "Nortel-i2004-A,10.2.100.200:4100,1,5." lease 0 2!!!!no file verify autospanning-tree mode pvstspanning-tree extend system-id!vlan internal allocation policy
[Code]...
View 2 Replies
View Related
Jun 11, 2012
I currently have 4 3560 switches connected in a Mesh topology. These are all set to use Jumbo Frames and so are all the Servers that are connected to these.I now need to connect a 2950 switch to 2 of the 3560's which will have only desktop computers connected to it but i do not want to configure Jumbo Frames on this and any of the desktops.
View 3 Replies
View Related
Aug 21, 2012
Currently using Cisco ISE 1.1 to authentication both dot1x and mab from Cisco switches. Both features are authenticating properly.When we use a Nortel/Avaya switch for the authenticator, we are unable to authenticate using mac bypass (non-eap (or neap) in Avaya talk..). The correct authentication policy is found in the ISE, but the mac address is not found in the database. We know it is there because the same mac is authenticating with the Cisco switch. Dot1x authenticates properly from both the Cisco and Avaya authenticators. Could this be an issues with the username/password format in the Radius packet from the Cisco?
View 5 Replies
View Related
Nov 23, 2011
We are having one HP core switch and VLAN is configured on it. Four Nortel BES1010(24port) switches will be connected to this HP switch. We need to configure the VLAN tagging in the Nortel switches in order to make deices connected to nortel switches can communicate with devices in the VLAN.
View 3 Replies
View Related
Oct 17, 2012
I have been looking at deploying a small core switch design for an important branch office that would consist of 2 cores with an etherchannel link and then 4 POE access switches linked to both cores utilising STP. I will also want static IP routing on the cores and will set up HSRP for gateway failover.
The initial switch I looked at for the core was WS-C3560E-24TD-S however after finding that there is no stock around of this at the moment I have seen the WS-C3560X-24T-S which looks like it will do everything I need including IP routing, HSRP and QoS for VOIP. The thing that concerns me is this is about £1000 cheaper so i'm slightly worried im missing someting.
View 6 Replies
View Related
Jun 13, 2012
Are 887VAM-W-E-K9 and 800-IL-PM2 compatible? We have got both of them but it seems that router has a 30W power source and module has a 80W power source.
View 1 Replies
View Related
