Cisco Switching/Routing :: 3560 Switches Stuck In Initializing Flash Loop
Nov 7, 2012
I have a couple of 3560 switches running c3560-advipservicesk9-mz.122-44 and they are randomly experiencing the following:
- The switch locks up with no preceding error message in the log (I am forwarding syslog to Splunk).
- Upon reboot, the switch goes through the normal startup sequence with no error messages, then for some reason reloads the flash and starts all over again. (refer to doc)
This could happen after days or weeks. Sometimes they will go through two of these reloads on boot and be fine for awhile, and other times they will be stuck in the loop infinitely. I am using this same image with all of our 3560s, but am only having this issue with two of them.
View 2 Replies
ADVERTISEMENT
Feb 17, 2013
I have a Catalyst 3560-X PoE that suddenly stopped working. I plugged in via console and below is the output I received. It scrolls constantly and I am unable to enter ROMMON mode or stop it from scrolling. I've read of a possible problem with the IOS version but I'm unable to verify due to not being able to stop the scrolling.
Switch uptime is 4 minutes, 4 seconds
cisco WS-C3560X-24P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1522R2AY
[Code].....
View 5 Replies
View Related
Jul 12, 2012
We did an upgrade from NX-OS 5.1.5 to 5.2.4 and found all M1 line card interfaces were stuck in initializing state for long time.'show module' status says ok. And we cannot execute shut/no shut command under the interface. N7K-M108X2-12L & N7K-M148GT-11 are the two M series cards. Only option was to downgrade back for the time being.
N7K01# sh int e1/1 | in down
Ethernet1/1 is down (initializing)
View 3 Replies
View Related
Oct 25, 2011
I am having an issue with this device after setting the ip address and rebooting. I have tried renaming the config.text file without success. I have also tried the steps mentioned here: [URL]
View 1 Replies
View Related
May 9, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop :I know that the solution would be to download a new valid image from tftp via the rommon prompt but what i dont undertand is why i cant access the rommon prompt. It justs boots with the message above in a loop
View 0 Replies
View Related
Mar 24, 2013
I have a strange issue where spanning-tree is blocking vlans through a mesh network.Here is my set up.
2-Cisco 3560's that have two trunk ports set with do1q and a native vlan of 2. I'm allowing a client vlan (2) and a voice vlan (103) to come over the trunk. They have a native vlan of 2 so the mesh APs can get an address through DHCP. Spanning-tree loop guard is also enabled.
When connected to the mesh network, the voice vlan is being blocked by spanning-tree. I get the following erros:
000129: *Feb 28 19:24:58.289 EST: %SPANTREE-2-LOOPGUARD_BLOCK: Loop guard blocking port FastEthernet0/1 on VLAN0103.000130: *Feb 28 19:24:58.448 EST: %SPANTREE-2-LOOPGUARD_UNBLOCK: Loop guard unblocking port FastEthernet0/1 on VLAN0103.
Eventually the loop is cleared and the port is set back to a forwarding state from a blocking state. I don't want to disabled spanning-tree loopguard since I don't want to create a loop. The mesh network is supposed to act as a P2P connection between two switches. As a test I disconnected the APs from their trunk ports. I then used a cross over cable to connect the switches and no spanning tree loops occured. The mesh doesn't have STP enabled on it and should just be acting as an over-the-air connection from one switch to another.
View 1 Replies
View Related
May 2, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies
View Related
Mar 4, 2012
I have 5 to 6 878 routers and in all these routers the ATM interface is stuck up with initializing mode. This is the IOS running on it c870- advipservicesk9-mz. 124-15.T9.bin
View 1 Replies
View Related
Nov 24, 2012
We have a couple of cisco SGE switches connected to a single DELL, between the cisco switches we have a trunk interface. I'm not sure which setting should be configured on the switches to get it working because a loop is occuring.
View 1 Replies
View Related
Jun 7, 2012
I have a bunch of 3750x switches that each have a 10 gig routed link back to a central 4507 (loopback = 172.30.255.255).We carved up a /24 (of course, the /24 doesn't really exist except in our address tracking spreadsheet) into a bunch of /30's for routed WAN links and /32's for loopback addresses.We started on the low end for /30 subnets (ie 172.30.255.0/30, 172.30.255.4/30, etc.).We started at the high end for the /32 loopbacks (ie 172.30.255.255/32, 172.30.255.254/32, etc.)
Well, when I try pinging 172.30.255.255 from the access layer 3750x switches, the 3750x seems to be treating it as a broadcast ping where it lists each member that responds instead of the regular !!!!! response (this makes think something is odd with the 3750x). Of course, only one member responds (the core). But even the core seems to respond with the other end of the /30 instead of the actual /32 loopback (which makes me think something is odd in the core). I could have sworn that I've setup similar topologies without problems (ie, using 10.0.0.0/32, 10.255.255.255/32, etc as loopbacks) and as long as the mask is a /32, it should work.Also, I can ping/ssh to that loopback if my laptop is on a directly connected subnet. But I can't do it from any of the 3750x switches (which are also directly connected).I've double checked for overlapping subnets, but nope. I don't see any. Routing looks fine. The actual /32 is being propagated everywhere properly.
View 3 Replies
View Related
Feb 5, 2013
We have a Cisco 3750G Core switch which has physical connections, each configured as trunks to two HP Access switches. The client who uses these access switches would like to put a link between the two, but this would create a loop.
------- Core Switch -------
| |
| |
[Code]....
View 12 Replies
View Related
Jan 17, 2013
I have newly purchased Cisco 887 Router. I am trying to replace this router with the exisiting ISP provided modem I am facing an issue to bring the ATM0 port up.
Here is my router config
hostname Internet Router
!
boot-start-marker
boot-end-marker
!
!
no logging buffered
[code]....
View 5 Replies
View Related
Nov 13, 2012
I just recently upgraded my 3845 to 15.0.1M9 and everything was going fine until I turned it back on later today. It is now stuck in a loop and wont even allow me to access ROMMON. I took out all additional hardware and it is still stuck at this screen. [code]
View 2 Replies
View Related
Feb 5, 2012
I've got several 3502i's that refuse to join to the controller, and just get stuck in a cycling blinking colors on the LED. Other AP's off the same port, controller, work fine. Logs are as follows...
*Feb 6 19:40:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.160.4.7 peer_port: 5246
*Feb 6 19:40:37.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code]......
View 12 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Jan 19, 2012
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
View 3 Replies
View Related
Dec 6, 2011
Is it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
View 2 Replies
View Related
Jul 22, 2012
Was building a small network in Cisco Packet Tracer and ran in to an issue. I have 4 routers running OSPF, and off one of the routers I have 5 3560 Multilayer switches. The router that the switches hang off of, I have a sub-interface with dot1q encapsulation, set for vlan 10 and an IP Address. 10.14.16.1/24. The switches have interface vlan 10 configures, and have IPs in the same subnet. From that router, I can ping/telnet to all the switches without issue. My problem arises when I try and reach those switches from any other router. OSPF is set to redistribute static and connected subnets.The routing table is populated correctly on all the routers. When I ping and trace the packet, it looks like it makes it all the way to the respective switch, but the packet never makes it back. I've played with the default route on the switches to no avail. Am I trying to implement this incorrectly, or am I just missing something?
View 4 Replies
View Related
Sep 5, 2012
whether VSS technology support on 3560 switches.I'm planning to intergrate new Cisco 2x6509 with VSS and all the access swtiches 3560's uplink to core 6509..if not support, what will be the solution or any bug fixing or new IOS releasing
View 1 Replies
View Related
Sep 9, 2012
In cisco documentation for the 3560 it is mentioned that blocking appletalk will not work .It shows up in command line but it is not working due to hardware limitation.Is there any other way to block appletalk on 3560 swiitches.
View 3 Replies
View Related
Apr 24, 2012
I have a question about RSPAN, is this feature only supported on 6500 and 4500 switchs?
we have 2 3560 switches and want to use RSPAN to monitor different source ports.I checked thorugh the cisco feature navigator and the IOS we have on 3560 has the RSPAN fature listed in them.
View 2 Replies
View Related
Jul 16, 2012
OSPF normally only comes with IPservices image and not IP Base image. The 3560-C series data sheet says that it only suport IP Base image, yet it mentions that support for OSPF in included. Are there any restictions in the OSPF support?.
View 7 Replies
View Related
Sep 3, 2012
I have a 5K with 5 downstream 3560's. I now have a new 5k that I would like to add to the existing 5K as a HA peer. What is the best way to accomplish this with the least amount of downtime for the downstream switches.On the 3560's, i plan setting up port-channels once HA is setup on the 5k's.
View 1 Replies
View Related
Sep 21, 2012
We have 7 3560's in 7 different locations connected to our providor for wan access. Our provider has given us a copper cable at each point and we have connected it directly to our 3560 switch at each location. Each port is configured the same way at each location. Each switch is running eigrp.All of the switch ports on each switch are configured as a trunk and vlan 299 had the ip address for the eigrp connection: [code] This setup is working as each switch see's all of the other switches as an eigrp neighbor. We have also made sure that the switch at our head office has spanning tree priority for vlan 299.
So the problem is, if there is a change in the topology at one of the locations it usually causes one or more of the other connections to go down for some reason. We just cannot pinpoint what is causing this change. There are no log's or anything other than an eigrp hold time expired message.?
View 9 Replies
View Related
Feb 19, 2013
We have a couple of Cisco switches and connected a (Windows 7) laptop to one of them and it gets its IP address from a DHCP server.I can now ping the IP from all of the switches, no problem, also not when I log on to the core switch in the same VLAN as both notebooks. But from my (Windows 7) laptop, which is in the same VLAN as the target laptop, I cannot ping it.
I checked, default gateway is good on both sides, as are DNS servers.
Target notebook ---- Catalyst 3560 V2 switch === Core Catalyst 3750 switch (stack) === Catalyst 3560G switch --- My notebook
View 4 Replies
View Related
Jul 9, 2012
For some special arrangement, I would like to connect 2 access ports from a 3550 switch to 3560 switch.1 port for vlan 200, another port for vlan 201.Will this introduce bad thing to the switches?
View 4 Replies
View Related
Sep 12, 2012
I have a Cisco 3560 connected via fiber to a Nortel 1612G. The connection is up/up, the V LAN's on the switch work as needed, but I can not ping the switch from the Nortel, and as a result I can not remote into the Cisco for management. I see in the configuration for the trunk that it is configured for a native v LAN, but I don't see it defined which v LAN's are allowed, could this be the issue? I will provide some of the config information for the Cisco side, I understand the issue may be on the Nortel end but if the Cisco part looks OK?
Port config for the trunk:
interface GigabitEthernet0/49
description port_6_1612G
switch port trunk encapsulation dot1q
switch port trunk native v LAN 120
switch port mode trunk
Native v LAN config:
interface Vlan120ip address 172.16.120.11 255.255.255.128
View 3 Replies
View Related
Apr 25, 2012
I have a connection between switches, There are a 3560 (Gi0/37) and a 2960 (Gi0/1), the problem is in the port Gi0/37 of the 3560 switch and this is the log. [code]
I dont understand what is the problem, actually i have added the command power inline never on the port and the problem is solved, but we haven´t changed configuration.
View 3 Replies
View Related
Jun 3, 2012
We have two Cisco switches with one 3560 and one 3750 we have created a new Vlan 4 with IP 10.1.3.x 255.255.255.0 - no shut then assigne to gi 2/0/46 on the 3560 Vlan 4 ip address 10.1.3.x 255.255.255.0 no shut then assign to FA0/45. All interfaces are up up along with the Vlan up up, we can ping the local IP address bu not able to pint the other switch.
View 2 Replies
View Related
Jan 16, 2013
We are in the process of rolling out iPads to our offices. As part of this implementation, we need to print from the iPads to our network printers. Our network printers are mostly HP and Xerox and do not have native Apple AirPrint capabilities. As such, we have been using the FingerPrint software to share out the network printers as Apple AirPrint printers. We have a mixture of switches at our offices. Most offices utilize a 3550 PoE switch. In these offices the AirPrint traffic is being transferred successfully and everything works great. In the offices which are using 3560 PoE switches, the traffic is never seen at the iPads. We are using EnGenius EAP300 access points connected into the Cisco switches to provide wireless access to the iPads. Both 3550 and 3560 switches are running iOS 12.2(25). What might be stopping/blocking the AirPrint traffic on the 3560 switches?
View 3 Replies
View Related
Jul 15, 2012
I have 3 3560 switches which are configured with trunks between them. They run vlan 10, 11 & 12. I have a 'core' switch (switch 1) of these 3 to which an MPLS router is connected on vlan12. I in addition have another switch hanging off the 'core' switch via a routed link (switch 4). I have EIGRP configured as a stub and as such the IP address on the routed link at the core switch end is of a /24 from v lan 1 on the other switch. This makes the route directly connected and therefore distributed via EIGRP stubs. Switch 1 is then exchanging routes with the MPLS router (via EIGRP).
The problem I have is that from any sub net on any switch (switch 1, 2 or 3) I can ping 192.168.13.1 (switch 4). When I try and ping switch 4 from over the MPLS I am unable to. If I trace to the switch I see it reaches the outside of the MPLS router, but is then unresponsive. The same applies if I try to ping switch 1 on 192.168.13.2. Any of the other IP addresses of switch 1 respond.
The MPLS network is a managed solution to which I have no access. I'm told that the MPLS provider is able to ping switch 1 & switch 4 on the 192.168.13.x addresses from a remote router (192.168.32.2). I have tried from a switch on the same L2 sub net (192.168.32.1) and I don't get a response.
From switch 4 I am able to ping the switch on 1 of it's interfaces (192.168.19.1), but not the interface I mentioned above 192.168.32.1. There are no access lists in place on the switches and no firewalls between the sites.
View 22 Replies
View Related
Feb 5, 2013
I have 3560's in my current environment, operating in the core/distro/access layers. The switches are in a star configuration, performs only layer 2 switching, and utilizes copper (no plans on moving to fiber).
With a fairly limited budget, I've been contemplating on upgrading the central node to a stacked 3750X to eliminate that single point of failure, and trunk the rest of the 3560's to the stacked switch. I wanted to be sure that the 3750X switches will be right for my environment (90-100 hosts), and if what I explained above is a good solution.
I'm also looking like to upgrade 6-7 of my servers (and SAN) with 10GB network cards. Do the ports on the 3750X have port densities capable of 10GB? If not, what switches provide that capability?
View 10 Replies
View Related
Feb 20, 2013
I need to support a bunch of security cameras mounted on poles in our parking lot and an IP intercom system mounted on some gates. Because of environmental factors the switches at the poles need to be hardened and the spec from the vendor installing the gear is for GarretCom Industrial unmanaged switches which would make sense.
However when Information Security got wind of this scheme they (probably correctly) are requiring me to secure the ports that these unmanaged switches connect to. I have 2 choices: port security w/ MAC filtering or 802.1x. Because all the devices at the poles and gates support 802.1x and because I may need to go out there to troubleshoot stuff (and will invariably forget to add the MAC of whatever device I am using) I would prefer 802.1X multi-auth mode.
Problem:
When I ran a quick test on a test 3560 running some 15.0.1 code I could get a laptop to connect via 802.1x EAP-TLS successfully if it was directly connected but when I connected the same laptop via a dumb Netgear switch I confiscated from a luser it would not connect. The 3560 error said that the laptop never responded.
Question:
Before I spend a whole lot of time on this, is this something that should work? I don't see any practical use for the feature if it won't however the documentation I am using specifically mentions downstream hubs but I am not sure if they mean real hubs (which I don't think are even made anymore) or if they mean unmanaged switches.
I plan to try a couple of different unmanaged switches tomorrow and digg a little but I would like to know if I am wasting my time on something that will never work or if there is a little gotcha somewhere.
View 2 Replies
View Related
