We did an upgrade from NX-OS 5.1.5 to 5.2.4 and found all M1 line card interfaces were stuck in initializing state for long time.'show module' status says ok. And we cannot execute shut/no shut command under the interface. N7K-M108X2-12L & N7K-M148GT-11 are the two M series cards. Only option was to downgrade back for the time being.
N7K01# sh int e1/1 | in down
Ethernet1/1 is down (initializing)
I have a couple of 3560 switches running c3560-advipservicesk9-mz.122-44 and they are randomly experiencing the following:
- The switch locks up with no preceding error message in the log (I am forwarding syslog to Splunk).
- Upon reboot, the switch goes through the normal startup sequence with no error messages, then for some reason reloads the flash and starts all over again. (refer to doc)
This could happen after days or weeks. Sometimes they will go through two of these reloads on boot and be fine for awhile, and other times they will be stuck in the loop infinitely. I am using this same image with all of our 3560s, but am only having this issue with two of them.
I have 5 to 6 878 routers and in all these routers the ATM interface is stuck up with initializing mode. This is the IOS running on it c870- advipservicesk9-mz. 124-15.T9.bin
View 1 Replies View RelatedWhy this same kind of bug/error/software fault exist in LMS 4.2 as it was in LMS 3.2 ? Why after a while after discovery of devices (state is "Known") DFM drops the state of devices to "Learning" and it stucks forever. Restarting of daemon manager works for a short time. It looks like the processing of faults stops a while after discovery is complete.
LMS 4.2 is running on Solaris 10, connected to other LMS in DCR Slave configuration.
I have this one device that is stuck in DFM Questioned state. The device is correctly discovered in CS and I have collected its configuration through ConfigMgmt (RME).I run Device Troubleshooting against it:
View 1 Replies View RelatedI have newly purchased Cisco 887 Router. I am trying to replace this router with the exisiting ISP provided modem I am facing an issue to bring the ATM0 port up.
Here is my router config
hostname Internet Router
!
boot-start-marker
boot-end-marker
!
!
no logging buffered
[code]....
Cisco Prime 4.2. My device is stuck in Questioned state in Fault Management. The device though can be pinged from the server. Actually, I can already manage the device and have archived its configuration. Problem is, on Fault Monitoring Device Administration, its on Questioned state even though I already tried to rediscover the device several times.Do I need to configure something on the server like put in the IP address and hostname of the device in the host file of Windows Server 2008?
View 1 Replies View RelatedI am working on LMS 3.2 . Tried to stop the daemon service with " net stop crmdmgtd ". It stuck on stopping state since few hours now. I can still open the application. How to terminate the previous command and restart the daemon service.
View 1 Replies View RelatedUser is connecting to 5508, running 7.0.116.0. Previously worked on another AP. TV (client) is set to use dhcp. As other posts have mentioned, "DHCP Addr. Assignment" checkbox is not checked for this wlan, but I also switched it to Required for this wlan but it did not make any difference. Seems to be a problem with just this client as many other clients are on this AP with no problems.
Users have to register their MAC to get on our wireless system, but there is no encyption or security enabled once the device has been registered.
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
I would like to request assistance from all the gurus here for an issue i have with a Cisco 7513MX PSU. There probably arent many people who are aware of 7500 chassis as they are quite old.Isse: PSU 1 failed in chassis and we tried to replace it. Once replaced, we are getting the following output for it:
1#sh env all
Arbiter type 2, backplane type 7513MX (id 2)
Power supply #1 is TBD (id 0), Power supply #2 is 1200W AC (id 1)
We have been researching on the internet for answers but unfortunately due to the age of this model, there is very limited information available. We did find information which suggested to have BOTH PSU 1 & 2 with same revision. Right now the chassis is running only on PS2, we dont want to take down the chassis just to confirm the revision number on the PSU and there is no way to see that on the CLI. What we can do is get another pair of same revision PSUs, insert PSU1 first THEN take out PSU2 and then insert the same revision as PS1 in PSU2 slot but the moment we insert PSU1 in we get that TBD state which is not normal status and raises our doubts about putting the same revision PSUs with the method above, there is a chance that after we insert PSU1 in, the moment we take out PSU2, the chassis might not run on PSU1 due to its abnormal state.
I have two Cisco 6500 switches connected via fiber, this is my small network. One end goes to a provider, and the other end goes to a server. My IT department wants some sort of link state propagation since the provider keeps going down, but the IT team is unaware until they contact me.
We provide a Layer2 point-to-point circuit, access ports at the ends. We use V LAN's to transport the traffic. Please let me know if there is anything I could do to support link state propagation.
indicate why my ethernet ports are in suspended state for some reason, i need an indication why this may be and what i can do to fix this issue. configuration below. I have a 7010 which i'm using to connect to two 5510's. I have one vPC connecting the two 5510's to the 7010. I have a vPC domain configured between the 5510's. and no issues at all. My Nexus 7010 port channel members are suspended for some reason.
Nexus 7010
vpc domain 100
role priority 100
peer-keepalive destination 192.168.1.2 source 192.168.1.1 vrf vpc-keepalive
!
interface Ethernet 3/1
[code]....
I am testing 2960 24 S with storm-control and Errdisable Port timer interval 60s , connected HUB on fa0/17 to make traffic / loop.After Strom Control detection the interface goes down thats ok after 60s they will try to recover the interface and going up although the loop is still there.For my understanding if the interface detect still a loop on that interface they will disable the port again for 60s and will check again. [code]
View 7 Replies View RelatedWe have a number of 3750 stacks used as access layer switches connecting Siemens VOIP phones and then a PC that connects to the phone.
For example if I plug PC A to the phone that connects to port 13 I pick up an IP addressand all works as predicted now if I plug in PC A to any other VOIP phone that connect to another port on the same switch it goes in error disable state ITs like the switch is holding my PC mac address and locks it down with the port which in my case is Gi2/0/13.
interface GigabitEthernet2/0/13
switchport access vlan 726
switchport mode access
[Code].....
I am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies View RelatedWe inserted a new module with 48 rj45 ports in a 4500 with just one supervisor module. We have two 4500, and we tried the new model in the other 4500 and it´s working properly and giving a OK status. Furthermore, the module´s LED status is green. We saw that there are 8 ports (from 17 to 24) that are in faulty state, so probably this is the cause for the faulty state for the module.
We tried already a Hw reset, replace/insert again the module...
We are almost sure that it can be a Hw failure. We are getting the following results different commands:
show module :
Mod Ports Card Type Model Serial No.
7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAXXXXXXXH
M MAC addresses Hw Fw Sw Status
[Code].....
After a power problem at our data centre we find Module 11 of our Cisco 6513 Core Switch in PWR Down state.Show Module 11 returns: Status: PWRDownShow Power Status Module 11 returns: OperStatus Off (Module Reset due to an exception or user request).The command:
Power enable Module 11 was issued and returned the following: %PM_SCP-SP-1-LCP_FW_ERR: System resetting module 11 to recover from error: Linecard received system exception. Errcode = 2509000001.%OIR-SP-3-PWRCYCLE: Card in module 11 is being powercycled Öff (Module reset due to exception or user request%C6KPWR-SP-4-DISABLED: Power to module in slot 11 set off (Module Reset due to exception or user request),We have restarted the switch twice. The module is currently not passing traffic causing downtime to services.
We have a pair of 6500 switches, each having a trunk going to each access switch. We set the spanning tree priority on Core1 so it is the root bridge for all VLANs. We have two different types of access switches:
-3550 setup as VTP client and ISL
-2960 setup as VTP transparent and dot1q.
Pruning is disabled but we use "switchport trunk allowed vlan" to restrict which VLANs go through each trunk. When we need to permit a VLAN through a trunk, we simply run "switchport trunk allowed vlan add <VLANID>" on the access switch and both core switches. If it is a 2960 in VTP transparent mode, we must set the VLAN to active. Once this is done, a "show int trunk" will reflect the new VLAN in "Vlans in spanning tree forwarding state and not pruned" for Core1.
I recently went through this process to add VLAN 250 on a 3550 access switch, but the VLAN is not listed in STP forwarding state and not pruned. I tried removing the VLAN from the trunks and redoing it, but there is was no change. I tried adding VLAN 257, but the same behavior happened. I then tried trunking the same VLANs to a few other access switches. Three other 3550s experienced the same behavior, but I was able to trunk the VLAN to a few 2960 switches. At this point, I figured it might be related to some kind of limitation of VTP or the 3550 switches. I provisioned a new 3550 with the same IOS and settings (VTP client, ISL). To my surprise, all VLANs configured were in STP forwarding state and not pruned.
Running show spanning-tree on the core and access switch shows VLAN 250 as designated FWD. I confirmed we are not hitting the limits in "show spanning tree summary totals" on the Core or Access switches. I also confirmed we are not hitting the virtual port limit by running "show vlan virtual-port slot x."My next action might be to shut/no shut the uplink to Core1 from the access switch, but I'm not sure if that will fix it and even if it does, I have no clue what caused the issue.
I have a Catalyst 2950G when I activate the switchport port-security, but I want to empty the black list of mac address because every time I connect a device, the port is automatically désacative, here is the port configuration:
!
interface FastEthernet0 / 2
switchport access vlan 17
switchport mode access
switchport voice vlan 51
[code]....
I tried the following commands to clear the blacklist mac address of that port, but the problem is still relevant:
# Clear mac-address-table dynamic int fa0 / 2
# clear port-security all int fastethernet 0/2
# clear errdisable interface fa0 / 2 vlan
I have catalyst 6500s with two VS-S720-10Gs, one is in Active and one is in Hot state. Both Sup cards have two 10G uplink ports. How does the traffic forwarding works in this case on the uplink ports? Do these uplink ports actively forward traffic or it is only the uplinks ports on Active that forward traffic? I see CDP neighbors on both Active and Hot SUPs uplinks ports - it indicates that packets are flowing on both cards.
I want all uplink ports on both SUPs to actively forward traffic. Does it work? What is the config for this?
Recently on two switches, both being same cisco WS-C3750E-24PD, running with same IOS c3750e-universalk9-mz.122-58.SE2.bin got noticed that the license state of one switch is showing incorrectly as shown below [code] I will not be able to execute any changes/modifications on switch as of now.
View 9 Replies View RelatedI have configured a SVI in my 4500 ( Sup 7-E 10GE,,,,,,and,,,,,cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin) switch and it is showing Down Down, because there were no active switch port in the vlan, I added one switch port to this vlan but this port also in the down state, so i added the SWITCH PORT AUTO STATE EXCLUDE command under this port, even after this also the SVI never came up, So i added one systen to the port so both the switch port and the SVI came up...So why SWITCH PORT AUTO STATE EXCLUDE command have no effect in this model of the switch..
View 4 Replies View RelatedI have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP. [code]
View 5 Replies View RelatedI have just received a new Cisco 3750G Switch from my parent company. When attempting to install the switch, I discovered that it will not boot to CLI, only to the bootloader. After using the command boot, the switch attempts to boot the most current IOS version, but fails, stating "error loading XXXXXXXXXX.bin".
Obviously, I just need to get a functional version of the IOS onto the switch to boot, but the problem is exactly how can I do that? All (or most) the commands with which I am familiar are unavailable in the bootloader, so all methods known to me fail. Is there a simple way (maybe using the copy command?) to put the .tar or .bin file onto the flash?
Stuck at Initial stage CISCO pix 515e
View 2 Replies View RelatedI have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies View RelatedMy Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
After a power outage our standby VSS switch has not recovered. The switch keeps cycling through its initialization and then powers off all modules.
The Dead peer detection is working and VSL links are up.
I have a Catalyst 3560-X PoE that suddenly stopped working. I plugged in via console and below is the output I received. It scrolls constantly and I am unable to enter ROMMON mode or stop it from scrolling. I've read of a possible problem with the IOS version but I'm unable to verify due to not being able to stop the scrolling.
Switch uptime is 4 minutes, 4 seconds
cisco WS-C3560X-24P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1522R2AY
[Code].....
I have configured my new 3850 using the command line and all works well. I logged into the web interface expecting to see device manager with a pretty image of the switch etc.
However I am presented with the Express Setup page and even if i fill in all of the details again and click submit then nothing happens and this is all I can get.
I have version 03.02.01SE software.
I have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
We have a couple of 7911 that get stuck in Registering, each monday. During the week, no user reports the problem. But after the weekend, we get ready to hear complaints from our collegues. The same phones often experience this issue, although the other phones report no problems. The problem is temporarily solved when we issue "shut/no shut" on switch ports.
phone firmware version: SCCP11.8-5-2S
Interface configuration:
interface FastEthernet1/0/27
[Code].....