I have configured my new 3850 using the command line and all works well. I logged into the web interface expecting to see device manager with a pretty image of the switch etc.
However I am presented with the Express Setup page and even if i fill in all of the details again and click submit then nothing happens and this is all I can get.
I have version 03.02.01SE software.
i've got a stack of 3750's configured, everything is working fine, but the web interface for the stack will only present the web based express configuration page. I can't get it to go away. what needs to be done to clear whatever flag or register that causes this behavior. the cli is fine, it's not trying to force epxress setup there, only in the web interface. will reloading the software image fix this?
View 16 Replies View RelatedI just received three WS-C2960S-24TS-Land three WS-C3560E-48TD-S switches that i entered the Express Setup on as usual. On two of each type of switch i found the default network that is used to facilitate the Express Setup was 10.0.1.1 and the others used an IP range of 10.0.2.1, i realized this is a small negligible at best difference though i need to provide management with an answer as to why there is a difference between the two and can’t find anything online as to why there is a difference or something that proves there should be a difference. All the documentation I find sounding Express Setup notes that the IP range will be 10.0.1.1 not 10.0.2.1
View 3 Replies View RelatedCan the new Cat 3850 run MPLS ?
View 4 Replies View RelatedCisco has put up the data sheet for the new 3850 switches. What do you all think about this new unified wired/wireless concept?
View 11 Replies View RelatedI just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 7 Replies View RelatedI just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
View 2 Replies View RelatedWhat is the preferred access switch for new deployment. Choosing between 3850 and 3750x. I have to say that the 3850 wireless features will not be used in this deployment and 4 switch for stack is enough... Looked and read everything that I found in the press, I can not make an informed choice. I bow to 3850, but I was apprehensive following circumstances:1) not too positive reviews2) to long list of open caveats3) to long list of features are not supported in Cisco IOS XE Release 3.2.0SE4) IOS XE : (With regard to the first three points - yes, I understand that the product is new and it has not gone further stage of "childhood diseases" ...Regarding the fourth point - I understand correctly that this is the direction to be moving Cisco Systems and soon all products migrate from classical IOS to IOS XE and so on?
View 8 Replies View RelatedWith my brand new Cisco 3850 Switch, I got it configured with a LAN IP. Then, on my PC I opened up Cisco Network Assistant (version 5.8.5.1 which supports the 3850). I went to add the 3850 to the community by discovering the device, and was prompted with the user/pass box. The password I set was not allowing me to connect, and I realized it's because a username was required and I had not set up a username on the switch. So, I then configured an admin user with level 15 privileges on the switch. However, now when in CNA I try to add the 3850 to the community, it doesn't even prompt me for user/pass, it just says "unable to connect".
What do I need to do to add this 3850 to my community?
We have a new stack of two Catalyst 3850-48T's running IOS XE 3.02.00 (we are upgrading to 3.02.01 this weekend.)We noticed the CPU usage is around 30% even when there is almost no traffic going through the switch. We haven't seen any indication that it is causing a problem, but is this considered a normal baseline?I attached my config (with passwords sanitized,) show ver, show controllers utilization, and show process cpu history.
I noticed this behavior is normal on 2900XL/3500XL switches, but I didn't find anything relating it to 3850 switches. Does the same thing apply to the 3850 switches? [code] url...
I just completed installation of a stacked pair of 3850s in my datacenter. While I was installing them, I noticed that the lights on ports 1-8 on one of the switches were on solid even though there were no cables connected to that switch. I don't see anything in the logs or anywhere else in the CLI that indicate a problem, however the lights remain on. This only happens on switch 1, not switch 2. Once I plugged the cable into port 1, it flashes normally with activity, but 2-8 remain on solid even though nothing is connected to them.
Before I put the switches in place, I had configured them at my desk with the console connection, and those lights were not lit up.
The indicators on the front of both switches are set in STAT mode. I thought initially I had hit the button and flipped it to a different mode, but that is not the case.
I have a network coming up for a switch refresh. Management is pushing for 2960s and I would like 3850s. We are running Cisco Voice and Video over the network. I saw a few things that seemed to be in favor of a Layer 3 switch vs. a Layer 2 switch. Some items like better performance due to switching based on IP vs. switching based on MAC. Some information that will show the 3850 to be a better choice or that the 2960 is capable.
View 6 Replies View RelatedI pulled a brand new Cisco 3850 Switch out of the box yesterday. Following the Quick Start Guide, I put in the power module, powered it on, and waited for it to complete POST. Then, I plugged in an Ethernet cable between a laptop and the switch on a port in the front, and went to the web interface at https://10.0.0.1. I got to the Express Setup, and attempted to change the IP address of the switch to an IP on my LAN, along with other options. When clicking submit, it didn't appear to take. Upon refreshing in the Express Setup, the IP config was blank, so I once again configured it. This time clicking submit brought up a message that it was changing the IP address. I waited for it to finish, and when it looked done, I powered the switch off and took it to a different room to hook it up to the LAN for further configuration.
When plugging in the power at that point, the switch starts through the normal light process (System LED blinks green slowly), and then eventually the System LED blinks green very fast and never stops. It doesn't get to the point of having the system loaded and ready to log into. There's no amber lights, just the System LED flashing green fast. On the back, the Power module and all bay lights are green, and the Console light is green, but the Management port light is off.
I've tried using the reset button on the back of the switch two different times to reset it to default configuration, thinking I hosed it somehow, but it never goes past the fast blinking System LED.
Based on what i am reading on the Catalyst 3850 datasheet, the controller functionality comes by default if i have a IP Base of IP Services license on the switch. Is this correct or do i need additional license to enable the controller functionality?What capabilities does below license provide ?
LIC-CT3850-UPG (Primary upgrade license SKU for Cisco 3850 wireless controller)
I have one out of three Catalyst Express 520's I cannot connect to with Cisco Configuration Assistant or with a browser. I've used Wireshark to capture the problem, and it sends a TCP RST packet immediately upon any such connection attempt.
As these devices do not have a console port, how can I gain access to the device? We'd like to upgrade them but cannot pull the existing config.
Since these 520's don't support or are not configured for telnet/ssh and the only connection I can make is with a broswer and CCA, I'm wondering if there is a way to get the config into a text file as normally done.
I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
1- data
100 - phones
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.
We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
The switch must have been configured previously, but we don't know its IP address. It is no longer on the network, so we can restart it as much as we need to.
We followed the factory reset process:
1) Disconnect the switch from the power supply
2) Reconnect the switch while holding the "SETUP" button
3) Release the "SETUP" button when the status LEDs all turn Amber
4) Wait for POST to complete
5) Connect one PC to the port whose LED starts flashing
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
Are there any known issues or browser/OS incompatibilities with this model of switch? We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.
I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies View RelatedI'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies View RelatedI have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP. [code]
View 5 Replies View RelatedI have just received a new Cisco 3750G Switch from my parent company. When attempting to install the switch, I discovered that it will not boot to CLI, only to the bootloader. After using the command boot, the switch attempts to boot the most current IOS version, but fails, stating "error loading XXXXXXXXXX.bin".
Obviously, I just need to get a functional version of the IOS onto the switch to boot, but the problem is exactly how can I do that? All (or most) the commands with which I am familiar are unavailable in the bootloader, so all methods known to me fail. Is there a simple way (maybe using the copy command?) to put the .tar or .bin file onto the flash?
Stuck at Initial stage CISCO pix 515e
View 2 Replies View RelatedI have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies View RelatedMy Cisco seems to be stuck when it boots up, with the following:
Upgrade ROMMON initalized
And it goes on with self comperessing image then an OK but then it starts loading again all over.
After a power outage our standby VSS switch has not recovered. The switch keeps cycling through its initialization and then powers off all modules.
The Dead peer detection is working and VSL links are up.
I have a Catalyst 3560-X PoE that suddenly stopped working. I plugged in via console and below is the output I received. It scrolls constantly and I am unable to enter ROMMON mode or stop it from scrolling. I've read of a possible problem with the IOS version but I'm unable to verify due to not being able to stop the scrolling.
Switch uptime is 4 minutes, 4 seconds
cisco WS-C3560X-24P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1522R2AY
[Code].....
We did an upgrade from NX-OS 5.1.5 to 5.2.4 and found all M1 line card interfaces were stuck in initializing state for long time.'show module' status says ok. And we cannot execute shut/no shut command under the interface. N7K-M108X2-12L & N7K-M148GT-11 are the two M series cards. Only option was to downgrade back for the time being.
N7K01# sh int e1/1 | in down
Ethernet1/1 is down (initializing)
I have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
We have a couple of 7911 that get stuck in Registering, each monday. During the week, no user reports the problem. But after the weekend, we get ready to hear complaints from our collegues. The same phones often experience this issue, although the other phones report no problems. The problem is temporarily solved when we issue "shut/no shut" on switch ports.
phone firmware version: SCCP11.8-5-2S
Interface configuration:
interface FastEthernet1/0/27
[Code].....
Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedI am having an issue with this device after setting the ip address and rebooting. I have tried renaming the config.text file without success. I have also tried the steps mentioned here: [URL]
View 1 Replies View Relatedwe're facing a weird issue lately with a Cisco 2821.An interface stops responding after a few hours.The only way to bring it 'up' again is:
Hardcode: duplex or speed
or
shutdown -> no shutdown
there are no errors in the "sho interface" and no errors or entries in the log.
FastEthernet0/0/0 is up, line protocol is up
Hardware is Fast Ethernet, -
Description: Infopoint
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Image Download N2K-C2232TM-E-10GE
sh fex
FEX FEX FEX FEX
Number Description State Model Serial
------------------------------------------------------------------------
105 FEX0105 Offline N2K-C2232TM-E-10GE
[code].....