Cisco Switching/Routing :: Catalyst Express 520 Sends TCP RST
Aug 5, 2012
I have one out of three Catalyst Express 520's I cannot connect to with Cisco Configuration Assistant or with a browser. I've used Wireshark to capture the problem, and it sends a TCP RST packet immediately upon any such connection attempt.
As these devices do not have a console port, how can I gain access to the device? We'd like to upgrade them but cannot pull the existing config.
Since these 520's don't support or are not configured for telnet/ssh and the only connection I can make is with a broswer and CCA, I'm wondering if there is a way to get the config into a text file as normally done.
View 4 Replies
ADVERTISEMENT
Jul 11, 2012
I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
1- data
100 - phones
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.
View 2 Replies
View Related
Sep 30, 2009
We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
The switch must have been configured previously, but we don't know its IP address. It is no longer on the network, so we can restart it as much as we need to.
We followed the factory reset process:
1) Disconnect the switch from the power supply
2) Reconnect the switch while holding the "SETUP" button
3) Release the "SETUP" button when the status LEDs all turn Amber
4) Wait for POST to complete
5) Connect one PC to the port whose LED starts flashing
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
Are there any known issues or browser/OS incompatibilities with this model of switch? We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.
View 9 Replies
View Related
Dec 25, 2012
I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies
View Related
Oct 21, 2009
i've got a stack of 3750's configured, everything is working fine, but the web interface for the stack will only present the web based express configuration page. I can't get it to go away. what needs to be done to clear whatever flag or register that causes this behavior. the cli is fine, it's not trying to force epxress setup there, only in the web interface. will reloading the software image fix this?
View 16 Replies
View Related
Apr 10, 2013
I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies
View Related
Sep 1, 2007
Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies
View Related
Jun 18, 2012
is there a discover tool for such a switch, i forgot the assigned ip .
View 2 Replies
View Related
Apr 21, 2008
Is there a way to prevent resetting catalyst config by pressing and holding in the MODE button after powerup? I had entered in a basic config into my switch including passwords, etc. and was checking out different uses of the MODE button including setting the switch into express mode and I somehow managed to wipe the config and send the switch back into a default state by holding the mode button in for too long.
I want to prevent this from happening once the switch it is in production.
Not sure if it matters, but this is the 24 S model using the LAN lite image..
View 3 Replies
View Related
Mar 1, 2006
Does it have this switch some port mirroring capability (SPAN or other)?
View 2 Replies
View Related
Jun 2, 2013
I have configured my new 3850 using the command line and all works well. I logged into the web interface expecting to see device manager with a pretty image of the switch etc.
However I am presented with the Express Setup page and even if i fill in all of the details again and click submit then nothing happens and this is all I can get.
I have version 03.02.01SE software.
View 11 Replies
View Related
Jan 3, 2012
I just received three WS-C2960S-24TS-Land three WS-C3560E-48TD-S switches that i entered the Express Setup on as usual. On two of each type of switch i found the default network that is used to facilitate the Express Setup was 10.0.1.1 and the others used an IP range of 10.0.2.1, i realized this is a small negligible at best difference though i need to provide management with an answer as to why there is a difference between the two and can’t find anything online as to why there is a difference or something that proves there should be a difference. All the documentation I find sounding Express Setup notes that the IP range will be 10.0.1.1 not 10.0.2.1
View 3 Replies
View Related
Sep 10, 2012
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies
View Related
Aug 2, 2012
I have the network described below, on which I am running PIM.
(network) ---- Embedded Linux Router --(vlan 5)-- CAT 3560G --(vlan 5)-- Cisco 1811 Router ---- Multicast Listener
The Linux Router and the 1811 have formed a PIM neighbor relationship. The multicast listener sends an IGMP Join and I can see the PIM join leave the 1811 router (via "debug ip pim"). Using tcpdump on my linux router I never see the Join come in, but I can see the PIM Hellos (which is why the neighbor relationship formed).
View 2 Replies
View Related
Oct 24, 2012
I have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies
View Related
Oct 28, 2012
I have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies
View Related
Jul 24, 2007
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Nov 6, 2012
I know RD is used to make an IPv4 address unique in an MPLS VPN system.I don't understand why a PE sends the RD when advertises a route via BGP.I thought RD were only local significant. But I made a packet capture and the RD is actually sended inside the MP_REACH_NRLI attribute:
(from packet capture)
Label Stack=19 (bottom) RD=12:1, IPv4=172.16.22.0/24
MP Reach NLRI Route Distinguisher: 12:1
Why the RD is sent? I suppose that the PE receiving the update checks the Route Target Extended Community to know to which VRF associate the update and not the RD.I made a test between PE1 with RD 12:1 and PE2 with RD 13:1 and there was full routes exchanges, the same when both PEs were using the same RD(all this configured in the correct VRFs). The only difference is that PE2 now shows in their corresponding VRF BPG table "Route Distinguisher 13:1".
View 19 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Mar 19, 2013
I have peculiar challenge ahead of me and would like to get new perspectives.
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
For example:
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.
View 5 Replies
View Related
Oct 21, 2012
I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
I've attached my 2800 and 3560 configs.
View 3 Replies
View Related
Oct 28, 2012
We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24.
Is this configuration correct:
interface 1:
auto qos trust
interface 24:
priority-queue out
View 3 Replies
View Related
Aug 5, 2012
I have 1 house that is about 1/4 or 1/2 a mile away from the other house.I would like to setup an antenna that sends a wifi signal from one house to the house that does not have internet.I have a picture link that i drew up at the top. I'm not the best at drawing stuff so bare with me.Im going to type a path of the internet out to show you what I would like to get setup.[CODE]
View 1 Replies
View Related
Aug 20, 2012
i have a avraetec 2200 sereis wich has a amd turion65 processer with windows xp professional and one day the internet didnt work and i looked at the activity it said aquiring network adress and it said sending packets but not receiving and its not a problem with wireless because i conected directlty to the modem and i had the same probem and also there are other devices conected to the modem and they hav
View 1 Replies
View Related
Jun 4, 2013
Are there any best practices for preventative maintenance on Catalyst Chassis switches. Looking to build a PMI schedule for a customer. Or is there evidence not to perform it at all. Things like re-seating line cards, cleaning fan exhausts, etc.
View 1 Replies
View Related
Feb 7, 2012
Does the Catalyst 3560 support GRE ?
I know that Catalyst 3750X support GRE ,but Catalyst 3750X cannot work in hardware it.
Does the Catalyst 3560 cannot work in hardware too?
View 4 Replies
View Related
Jun 14, 2012
i have a cisco catalyst 2960g and for some reason out of the blue, some interfaces go down and then up. It started doing it after a power cycle.
View 1 Replies
View Related
Apr 22, 2012
I've gotten this out of our storage unit here at work: This was not in use, I've restarted it, I can't get into the flash dir,I've tried to restart the switch via the documents I've gotten on the site.I have the lastest iOS version .bin for this switch, but I can't get this to load: here below is what happens when I try.
View 5 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Oct 2, 2012
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies
View Related
