Cisco Infrastructure :: Catalyst Express 500 Port Mirroring Capabilities?
Mar 1, 2006Does it have this switch some port mirroring capability (SPAN or other)?
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Port Mirroring On A Catalyst 3560-X?
Oct 21, 2012I've just installed 2 of these in my workplace on a PLC network.I'm now looking to set one of the ports up as my diagnostic port and would like to be able to mirror any of the other ports to this port.I believe it is called SPAN on Cisco switches.The only reference I can find to it is configuring via Telnet which I haven't got a clue about.On my old Wiedmuller switches it was just a few clicks away.
View 3 Replies View RelatedCisco Switching/Routing :: Force Gigabit Ethernet Port To Be 1000 Full Duplex In Catalyst Express 500 Series?
Sep 1, 2007Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 4500 Or 6500 VSS Capabilities?
Dec 10, 2012Catalyst 4500 or 6500 VSS Capabilities?
View 6 Replies View RelatedCisco Switches :: Reconfigure Port Mirroring From Port FE17 To FE3 / SF200 Web Interface Crash
Mar 14, 2013i was able to configure (via SF200 web interface) a port mirroring from port FE17 to FE7.i have supressed this port mirroring.when i try to reconfigure a port mirroring from port FE17 to FE3. The SF200 web interface crash. the SF200 seems to reboot.
i have updated the SF200 firmware from V1.1.2.0 to V1.1.2.9.44 when i was able to configure (via SF200 web interface) a port mirroring from port FE17 to FE7.But after having suppressed this port mirroring again, i was not able to reconfigure a new port mirroring from port FE1 to FE3 (the SF200 hangs).
i have also tried to return to default factory setting but this does not solve the issue.i am working on SF200-24P
Cisco WAN :: ASR 1006 Supported Span Port Or Port Mirroring?
Mar 2, 2011is ASR 1006 supported span port or port mirroring? Any config about that?
View 2 Replies View RelatedCisco LAN :: Catalyst 500 Express Switch / Discover Tool?
Jun 18, 2012is there a discover tool for such a switch, i forgot the assigned ip .
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst Express 520 Sends TCP RST
Aug 5, 2012I have one out of three Catalyst Express 520's I cannot connect to with Cisco Configuration Assistant or with a browser. I've used Wireshark to capture the problem, and it sends a TCP RST packet immediately upon any such connection attempt.
As these devices do not have a console port, how can I gain access to the device? We'd like to upgrade them but cannot pull the existing config.
Since these 520's don't support or are not configured for telnet/ssh and the only connection I can make is with a broswer and CCA, I'm wondering if there is a way to get the config into a text file as normally done.
Cisco Switching/Routing :: Catalyst Express 520 - Trunk Configuration?
Jul 11, 2012I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
1- data
100 - phones
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.
Cisco Switching/Routing :: Catalyst Express 500 Factory Reset
Sep 30, 2009We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
The switch must have been configured previously, but we don't know its IP address. It is no longer on the network, so we can restart it as much as we need to.
We followed the factory reset process:
1) Disconnect the switch from the power supply
2) Reconnect the switch while holding the "SETUP" button
3) Release the "SETUP" button when the status LEDs all turn Amber
4) Wait for POST to complete
5) Connect one PC to the port whose LED starts flashing
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
Are there any known issues or browser/OS incompatibilities with this model of switch? We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.
Cisco WAN :: Preventing Reset Into Express Mode On Catalyst 2960
Apr 21, 2008Is there a way to prevent resetting catalyst config by pressing and holding in the MODE button after powerup? I had entered in a basic config into my switch including passwords, etc. and was checking out different uses of the MODE button including setting the switch into express mode and I somehow managed to wipe the config and send the switch back into a default state by holding the mode button in for too long.
I want to prevent this from happening once the switch it is in production.
Not sure if it matters, but this is the 24 S model using the LAN lite image..
Cisco Switching/Routing :: Configuration Of Catalyst Express 500 Series?
Dec 25, 2012I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies View RelatedCisco :: Port Mirroring On Switches?
Oct 31, 2011I have a Cisco Catalyst 3750X switch, and I have configured port mirroring on it. Traffic from 12 of the 1G ports will be mirrored to both 10G ports, and I have connected both 10G ports to a server that captures the traffic.
Currently, I have one of the 12 1G ports connected to another server that replays a pcap file once at maximum speed (i.e. option -t in tcpreplay). I thought that this setup means I should get twice the number of packets (and rate) from the two 10G ports. However, I noticed that although the original pcap file contains 4288 packets, the number of packets from the two 10G ports varies between 31000 to 34000 packets, which is about 7 to 8 times the original number of packets. Why am I getting more than twice the amount of traffic, and why does the output vary?
Cisco WAN :: Port Mirroring For 851W With 12.4T?
Jan 31, 2011I have looked up the command sequence for port mirroring and it seems pretty straight forward however in my case the command will not execute.
I have a 851W with 12.4T
If I do: #monitor session 1 source interface fa 4 (wan port)
i get the response invalid input detected however if I do the same command for fa 1, fa ,2 and fa 3 they work
Using the ? shows the valid entries are [0-4] for fastethernet
I just want to monitor WAN traffic with WireShark, particularly DDNS requests, with a spare PC connected to a free lan port.
I would use a hub on the Wan connection but unfortunately I do not have one at the moment.
Cisco Switching/Routing :: Catalyst 3570 Express Setup Webpage Not Go Away
Oct 21, 2009i've got a stack of 3750's configured, everything is working fine, but the web interface for the stack will only present the web based express configuration page. I can't get it to go away. what needs to be done to clear whatever flag or register that causes this behavior. the cli is fine, it's not trying to force epxress setup there, only in the web interface. will reloading the software image fix this?
View 16 Replies View RelatedCisco Switches :: Getting SG300-28 Port Mirroring?
Apr 28, 2013I have created a mirror to copy all packets from Interface gi1 to interface gi28. I don't see any port 80 traffic, or 443 or any revelant traffic. I see mostly broadcast from other devices. I have a security device that is logging all the copied packets from my firewall for malware/IPS, etc inspection.Right now I have it monitoring vlan 1 in the hope that it would resolve this issue but I see no change.
View 1 Replies View RelatedCisco Switches :: Port Mirroring On SG300
May 3, 2011I want to configure port mirroring on SG300 swtich, port monitoring status is "Not Ready" , and i can not monitor the source interface!
View 1 Replies View RelatedCisco Switches :: Getting The Port Mirroring On SG300?
Nov 8, 2011I'm troubleshooting a LAN issue I have, and I wanted to hook up wireshark to record traffic over the course of a couple of hours for later diagnostics. I went into the web administration interface, clicked Administration > Diagnostics > Port and VLAN Mirroring, and added a port mirror from the port I wanted to watch to a port to which I had connected a laptop. I picked the Tx and Rx options, and clicked Apply.I did receive lots of traffic in wireshark, but I noticed immediately that the server on the port I had mirrored was suddenly unavailable on the network -- pings timed out. This lasted until I removed the mirror, then the server was suddenly reachable once again.Does this feature not work the way I had thought it does? What I saw looked more like a forward than what I would call a mirror. The documentation leads me to believe mirroring is intended to be used in just the way I was attempting to use it.
View 1 Replies View RelatedCisco Switching/Routing :: Master Reset Catalyst Express 500 (WS-CE500-24TT V01)
Apr 10, 2013I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies View RelatedCisco Firewall :: Setup Port Mirroring On An ASA 5510?
Sep 14, 2011I'm trying to setup port mirroring on a Cisco ASA 5510, but when I try to use the switchport monitor command, that command is not recognized.I've selected what interface I want to configure (conf-if), but the switchport command seems to not be part of the IOS.I'm running ASA version 8.2(1)
View 9 Replies View RelatedCisco Switches :: Port Mirroring Limit On SGE2010?
Oct 25, 2012I have been told there is a limit (8) on the number of source ports that can be mirrored to a given destination port. I can find no specifications or other documentation to corroborate this claim. Any factual data to confirm or refute this claim?
View 7 Replies View RelatedCisco Switches :: Port Mirroring Limit Of 8 Ports On SGE2010P
Jan 24, 2013Recently our company purchased 3 Lynksys SGE2010p, At the moment they work as a stack but as we are implementing UCCX we need to mirror 15 ports but during the provisioning i've noticed that the limit is 8 ports per stack. I'm wondering whether this is a known issue or just a known limitation . I believe that most probably i'll need to move back to stand alone mode so i could configure 8 mirrored ports per switch.
View 2 Replies View RelatedCisco Switching/Routing :: 3548XL Port Spanning / Mirroring With Snort IDS
Oct 30, 2012I am trying to configure a SNORT IDS system running on a physical machine using Linux as the base OS. I have a small lab network setup with 3 VLANs, a 3548 switch and a 2611 router acting as the router on a stick/inter-vlan router. My goal is to setup SNORT as a host-based IDS system. To do that I know I need to use the "port monitor" command on the switch and I have tested this and it works fine only when the snort system and the traffic I want to monitor reside on the same VLAN.My problem is I want to be able to monitor a trunk link betwee the switch and router to see traffic coming from my 3 VLANs which contain servers. My goal is to run attacks on the servers to test SNORT's effectiveness.
Relevant information from my configuration: interface fa 0/1 on switch is the trunk like carry 3 vlans to the router On the switch:
int fa 0/1
switchport mode trunk
int fa 0/5
port monitor fa 0/1
switchport mode access
The switch will not allow me to configure fa 0/5 as a trunk, only can be an access port.So right now, SNORT does not see any traffic other than traffic from my router to the switch. I assume because this is going over the native VLAN (1 in this case) and that is the same VLAN that SNORT box resides on on interface fa 0/5. So I know the span is working to an extent, but traffic from my other VLANs (server to server traffic) does not show on SNORT at all.I have done some research on Cisco.com and see the following seemingly contradicting information:
VLAN Filtering When you monitor a trunk port as a source port, all VLANs active on the trunk are monitored by default. You can use VLAN filtering in order to limit SPAN traffic monitoring on trunk source ports to specific VLANs Then I see, under the section for the 3500 series: A monitor port cannot be a dynamic-access port or a trunk port. However, a static-access port can monitor a VLAN on a trunk, a multi-VLAN, or a dynamic-access port. The VLAN that is monitored is the one that is associated with the static-access port.
My question is, does that mean the 3548 cannot support spanning a trunk link and having all VLANs on that trunk be monitored correctly to the monitoring port? I know the 3548 is old, but it is the only thing right now I have to work with. I could put the SNORT box inline on the network, but that is another mess in itself.
Cisco Switches :: Does ESW 520 24P Support Mirroring 20 Ports Traffic To 1 Destination Port
Sep 5, 2011Does the ESW 520 24P Support Mirroring 20 Ports Traffic to 1 Destination Port?
View 3 Replies View RelatedSwitches On A Network Doesn't Support Remote Port Mirroring?
May 2, 2011If switches on a network doesn't support remote port mirroring and only local port mirroring, What are the options to still capture all the traffic from all switches on 1 single core switch?
View 1 Replies View RelatedCisco Switching/Routing :: Maximum Number Of Sessions For Port Mirroring On 4510
Apr 23, 2013Are you only able to have two sessions for port mirroring on a Cisco 4510?
View 1 Replies View RelatedCisco Switching/Routing :: Port Mirroring 2651 To Create Monitor Session From Source
May 20, 2013I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies View RelatedCisco Infrastructure :: Can't Upload IOS To Flash Of Catalyst 2900 XL
Feb 15, 2012We have a switch Cisco Catalyst 2900 Series XL Model WS-C2924-XL-EN. 8 MB DRAM 4 MB FLASH
I already tried the discussions regarding flash_init dir_flash: boot and the likes.
By the way, I already downloaded the IOS for our switch through Cisco Website. Settings are default through Hyper Terminal
Here's the thing:
Whenever I transfer the .bin file using XMODEM, it prompted an error "Transfer cancelled by remote computer"
Cisco Infrastructure :: Can't Upload By Tftp On Any Catalyst 2960
Dec 17, 2012i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies View RelatedCisco Infrastructure :: Using Catalyst 5500 As A TFTP Server?
Mar 11, 2003I need to do one Catalyst 5500 as a TFTP server.Can I do it?Is the catalyst available to be a tftp server?
View 4 Replies View RelatedCisco Infrastructure :: Poor Performance On Catalyst 4006 Sup II
Apr 3, 2003I have a Catalyst 4006 with Supervisor II engine. I have 48 port 10/100/1000 blades installed in it for connection to my servers. I am having a lot of problems with performance when connecting servers that are using 100 MB NICs. The speed of the connection is really bad. I have attempted setting the ports and NICs to 100MB Full duplex instead of auto-detect, but still get the same results.
I also have a 10/100 quad-port card installed in a NetApp filer. All four ports are trunked together and connect to 4 ports in the Catalyst. The ports in the Catalyst are trunked using the Port Channel feature of the CatOS. When I look at the port statistics on 3 of the 4 ports from the quad-card, there are a ton of runts and errors (both transmit and receive). The 4th port is fine, no errors.
Cisco Infrastructure :: Configure On Catalyst 6509 Two VACL
Feb 10, 2013 I need to configure on a cisco catalyst 6509 two VACL. On cisco 6509 there are already two SPAN ports configured, there are problems configuring other two VACL?
These VACLs send traffic to a Traffic Analyzer (SIEM), there are particular configurations to facilitate the operation?
Cisco Infrastructure :: Supervisor Engine Catalyst 6500 Modular IOS?
Oct 11, 2011I want to know the difference between the software that is Modular and the one that is not. What are the pros and cons ?
CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH or CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH (MODULAR)