Cisco Switching/Routing :: Configuration Of Catalyst Express 500 Series?

Dec 25, 2012

I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01)  and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Catalyst Express 520 - Trunk Configuration?

Jul 11, 2012

I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
 
1- data
100 - phones
 
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.

View 2 Replies View Related

Cisco Switching/Routing :: Force Gigabit Ethernet Port To Be 1000 Full Duplex In Catalyst Express 500 Series?

Sep 1, 2007

Can we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst Express 520 Sends TCP RST

Aug 5, 2012

I have one out of three Catalyst Express 520's I cannot connect to with Cisco Configuration Assistant or with a browser. I've used Wireshark to capture the problem, and it sends a TCP RST packet immediately upon any such connection attempt.
 
As these devices do not have a console port, how can I gain access to the device? We'd like to upgrade them but cannot pull the existing config.
 
Since these 520's don't support or are not configured for telnet/ssh and the only connection I can make is with a broswer and CCA, I'm wondering if there is a way to get the config into a text file as normally done.

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst Express 500 Factory Reset

Sep 30, 2009

We have inherited a Catalyst Express 500 (model WS-CE500-24PC) from a company we aquired, and are having issues configuring the switch.
 
The switch must have been configured previously, but we don't know its IP address.  It is no longer on the network, so we can restart it as much as we need to.
 
We followed the factory reset process:
 
1)  Disconnect the switch from the power supply
2)  Reconnect the switch while holding the "SETUP" button
3)  Release the "SETUP" button when the status LEDs all turn Amber
4)  Wait for POST to complete
5)  Connect one PC to the port whose LED starts flashing
 
However, the PC is never given an IP address, and when we open a web browser, anything we try to browse to gives us "Page cannot be displayed", rather than the setup page for the switch.
 
Are there any known issues or browser/OS incompatibilities with this model of switch?  We're using Vista and Windows 7 with IE7, IE8 and Firefox 3.

View 9 Replies View Related

Cisco Switching/Routing :: Catalyst 3570 Express Setup Webpage Not Go Away

Oct 21, 2009

i've got a stack of 3750's configured, everything is working fine, but the web interface for the stack will only present the web based express configuration page.  I can't get it to go away.  what needs to be done to clear whatever flag or register that causes this behavior.  the cli is fine, it's not trying to force epxress setup there, only in the web interface.  will reloading the software image fix this?

View 16 Replies View Related

Cisco Switching/Routing :: Master Reset Catalyst Express 500 (WS-CE500-24TT V01)

Apr 10, 2013

I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?

View 0 Replies View Related

Cisco Switching/Routing :: L3 Routing With Catalyst 4900 Series?

Mar 19, 2013

I have peculiar challenge ahead of me and would like to get new perspectives.
 
The objective is to route specific VLAN traffic and the caveat is that I have multiple VLANs with the same network address.
 
For example:
 
VLAN100 10.10.10.0/28 VLAN101 10.10.11.0/28 VLAN102 10.10.12.0/28
VLAN103 10.10.12.0/28
VLAN104 10.10.11.0/28
 
I need traffic going from VLAN100 with a destination of 10.10.11.0 forwarded to VLAN101 and NOT VLAN104.
 
This task is currently being completed by a multi context firewall and we're trying to decommission the asset.

View 5 Replies View Related

Cisco Switching/Routing :: NetFlow On Catalyst 4500-E Series

Nov 12, 2009

If a Supervisor 6-E will support NetFlow on a Catalyst 4507R-E?If not, what are my options for NetFlow on a 4507R-E?

View 7 Replies View Related

Cisco Switching/Routing :: Recover IOS In Catalyst 2960 Series

Jan 8, 2013

In an attempt to restore a Cisco IOS I deleted the file C2960-lanbasek9-mz.122-53.SE2.bin my swich
 
Before deleting the same was as follows:Directory of flash :/
 
3-rwx 12824 Mar 28 1993 21:00:37 -03:00 vlan.dat4-rwx 3096 Mar 7 2012 08:43:37 -02:00 multiple-fs5-rwx 2289 Mar 7 2012 08:43:37 -02:00 private-config.text6-rwx 7482 Mar 7 2012 08:43:37 -02:00 config.text9 drwx 192 Mar 23 2012 16:18:54 -03:00 C2960-lanbasek9-mz.122-53.SE2
 
32514048 bytes total (20204544 bytes free)Switch-01 #
 
Right now this switch as follows:
 
switch: dir flash:Directory of flash:/
2  drwx  64        <date>               crashinfo_ext    3  -rwx  4120      <date>               multiple-fs    5  -rwx  12824     <date>               vlan.dat    6  -rwx  4018      <date>     

[Code].....

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst 3750 Series Stack IOS Upgrade?

Oct 8, 2012

I have Cisco Catalyst Stack structure that  consist of;
 
3750E-48TD-S (MASTER) (UNIVERSAL Image)
3750G-48TS-S (IPBASE Image)
3750G-48TS-S (IPBASE Image)
3750G-48TS-S (IPBASE Image)
             
I want to upgrade their IOSs to k9 images.
 
I can not dowload Universal Image file from Cisco website because of the expired service contract.  I have IPBASE IOS files for all switches,
 
Can it be a problem to upgrade master switch IOS from Universal to IPBASE image?

View 1 Replies View Related

Cisco Switching/Routing :: Upgrading Catalyst 4500 Series Supervisor

Jan 8, 2012

Does a new Cisco Catalyst 4500 series supervisor 7L-E model WS-X45-SUP7L-E is backward compatible with a Cisco Catalyst 4500 series chassis model 4507R? I've checked on Cisco website for that Supervisor and it shows only new chassis models WS-C4507R+E and R-E, but what about old type of chassis? We need to upgrade that Supervisor as it's out of line, but we don't really want to buy a new chassis as well as it's going to be very pricy.

View 6 Replies View Related

Cisco Switching/Routing :: Star Wars Jargon In Catalyst 4500-E Series

Jun 21, 2012

When the 4500-E series switch boots and if you issue a 'show run' there's several Star Wars themed references and their revisions. What these actually are and why they are using Star Wars terminology?
 
Here's the output:
 
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICESK9-M), Version 12.2(53)SG2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 16-Mar-10 04:50 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x12794974

ROM: 12.2(44r)SG5
Darkside Revision 4, Jawa Revision 18, Tatooine Revision 140, Forerunner Revision 1.78

1AR1R2-NC1 uptime is 2 years, 2 weeks, 3 days, 15 hours, 44 minutes
System returned to ROM by power-on
System restarted at 19:29:14 UTC Fri Jun 4 2010
System image file is "bootflash:cat4500e-entservicesk9-mz.122-53.SG2.bin"

View 2 Replies View Related

Cisco Switching/Routing :: Limit Bandwidth Of Catalyst 3750 Series Switch?

Apr 23, 2013

I want to limit the bandwidth of my Catalyst 3750 series switch, I read the cisco documentation and I applied the commands but I didn't get the wanted results.

For the outbound traffic it's ok, but for the inbound traffic I used policing but I get an unstable traffic. I used, an access list and a class-map to classify the traffic and then a policy-map.(I followed the steps mentioned in this site: [URL]

View 4 Replies View Related

Cisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface

Feb 12, 2013

Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series  interface and services module, protecting customer investments?

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 4500 Versus 4500E Series - Blades Interchangeable?

Feb 6, 2013

What's the difference between a Catalyst 4500 and a Catalyst 4500E series chassis? I believe it has to to do with supporting PoE+? Are the blades in both series interchangeable?                   

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 2960 Series Ports Disabled When Connecting Vmware

May 21, 2012

I have a Cisco Catalyst 2960 series switch. When I connect another switch or a VMWare Esx server on one of the ports, the port blinks for few seconds and then goes off. When I connect a desktop or laptop or a windows server the ports stay led and I can access resources on the network. However, when connect another switch or a vmware esx server, the port is disabled.
 
What config in the switch can I check to make sure the ports stay on regardless when I connect a desktop / laptop, switch or vmware server?

View 2 Replies View Related

Cisco Switching/Routing :: CLI Configuration Of 800 Series Routers

May 1, 2013

I've goggled and searched here, and I can't seem to find what I'm looking for.  I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.

View 2 Replies View Related

Cisco Switching/Routing :: 800 Series Router Configuration

Jun 13, 2012

about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.

View 5 Replies View Related

Cisco Switching/Routing :: How To Copy Configuration From 2900 Series To Another One

Oct 11, 2012

I know we can use copy & Paste, my questions are:

1.       Before that, do I need to wipe out the existing confi on the brand new switch?

2.       About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 - DAI Configuration

Apr 26, 2012

Any step-by-step configuration guide of how to enable DAI on Cisco Catalyst 6500 Series Switches.

View 1 Replies View Related

Cisco Switching/Routing :: Configuration PBR On Catalyst 4503

Mar 4, 2012

i'm performing configuration PBR on catalyst 4503, but it doesn't work. [code]

View 21 Replies View Related

Cisco Switching/Routing :: Catalyst 2960G Vlan Configuration?

Oct 24, 2011

I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
 
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
 
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
 
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
 
Below is my startup configuration:
 
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id

[code].....

View 28 Replies View Related

Cisco Switching/Routing :: SPAN Configuration In Catalyst 3750

Dec 31, 2011

I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control).  I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8  (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.

View 5 Replies View Related

Cisco Switching/Routing :: WOL Configuration On L3 Catalyst 6500 And L2 2960G?

Dec 20, 2011

I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
 
Layer 3 switch Intervlan routing configuration
  
ip forward-protocol udp 7
!
interface Vlan4
description vlan Client-WOL
ip address 172.22.51.253 255.255.254.0
ip access-group Deny_HTTP_Vlan1 in
ip helper-address 172.20.1.246

[code].....
 
After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.

View 7 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration

Apr 22, 2013

I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration  between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
 
Civic_6506VSS#sho mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE   

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 3500 Fx Port Configuration

Jun 12, 2013

I am connecting two catalyst 3500 XL switches via fiber fx ports for layer 2 connectivity. Do I need to configure anything in the IOS or do I just plug in the fiber?
 
What needs to be configured?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3750 Failover Configuration

Jul 16, 2012

Our servers are hosted at the Main site, site office A access to the Main site for Internet and servers. We are thinking NextG to take over when the link between sites goes down.
 
To start with, what is the configuration for 3750 at Site A and the Main site:

1) Trunking for both switches

2) Routing

3) the automatic failover configuration for the switch at Site A.

View 1 Replies View Related

Cisco Switching/Routing :: WCCP Configuration On Catalyst 3750G?

Jul 5, 2010

I have a WCCP Configuration on a Catalyst 3750G and a IronPort Webappliance. I have configured this situation many times before with cisco asa and ironport wsa, but with a switch, this is my first time.
 
VLAN 147 is a transportation vlan between the cisco switch and a hp coreswitch with the clients and servers behind the hp coreswitch.
 
VLAN 147 IP Address of the Catalyst is 172.30.47.1
 
IP of the IronPort Appliance is 172.30.47.10
 
IP of the HP Coreswitch is 172.30.47.2
 
Plan  is to redirect the webtraffic coming from clients and servers from the 10.0.0.0/8 net behind the hp switch to the ironport wsa. In have configured these settings.
 
ip wccp web-cache group-list 15 password 7 091D1C5Aip wccp 80 redirect-list 16 group-list 15 password 7 14464058
interface GigabitEthernet1/0/22 description IRONPORT P1 BUWOG switchport access vlan 147 switchport mode access
interface Vlan115 ip address 172.30.15.2 255.255.255.0 standby 10 ip 172.30.15.1 standby 10 priority 90 standby 10 preempt standby 10 track Vlan115!interface Vlan147 ip address 172.30.47.1 255.255.255.0 ip wccp web-cache redirect in ip wccp 80 redirect in

[code]....

View 6 Replies View Related

Cisco Switching/Routing :: Copy Startup Configuration From 877W To Another 870 Series Router?

Jan 4, 2012

I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst 6506 Vlan-based Qos Configuration?

Feb 12, 2012

I was unable to configure vlan-based qos on Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXH6, RELEASE SOFTWARE (fc1) Seems to me my configuration is not working. Here is the output of the interface:
 
sh int G1/6 | i rate
Queueing strategy: fifo
30 second input rate 25231000 bits/sec, 4282 packets/sec
30 second output rate 46940000 bits/sec, 9257 packets/sec
 
And here is my configuration:
 
interface Vlan3
ip address 192.168.1.1 255.255.252.0
service-policy input TEST_IN_PMAP
service-policy output TEST_OUT_PMAP

[code]....

Why I can't see matches in ACLs? I've double checked the direction and seems to me it is correct. I can't see matches even I configure something like this:

10 permit ip host 192.168.1.168 any 
20 permit ip any host 192.168.1.168

Why my output rate is higher than 30M? Is it bacause there is no matching traffic here in ACLs? I'm absolutely shure that this host with such ip connected to this interface:

#sh arp | i 192.168.1.168
Internet  192.168.1.168           0   feed.beef.f00d  ARPA   Vlan3
#sh mac address-table |  i feed.beef.f00d
*    3  feed.beef.f00d   dynamic  Yes          0   Gi1/6

View 9 Replies View Related

Cisco Switching/Routing :: Catalyst 6509 - Ether Channel Configuration?

Dec 1, 2011

I came across a Catalyst 6509 switch configuration and have noticed some strange thing on the ether channel configuration side, it appears that it have interface port-channel 2 and port-channel 2A, what was that mean? its the ether channel not forming and joined together?
 
What wrong with the below configuration that cause it to automatic created another port-channel (2A) interface in this case?

[code]...

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6513 - FWSM Module Configuration

Dec 20, 2007

My company has acquired a Catalyst 6513 with a FWSM module installed on it. I have been reading lot of documentation on [URL], but still have some problems configuring the FWSM:
 
The 6513 has 10 SVIs configured, each of them with an IP address. These 10 SVIs are binded to 10 VLANs which I need to secure. These SVIs are used for routing all the Inter-VLAN traffic inside the switch. The documentation says it is recommended to use just one SVIs for connecting the switch to the FWSM, although you can use more than one using the command "firewall multiple-vlan-interfaces". I don't want to use this command because it seems a pretty more difficult configuration, since you have to use policy routing after using this command (or that is, at least, what documentation says).
 
When I try to "send" to the FWSM more than one VLAN that are configured as SVIs on the switch I get this error message:
 
"No more than one svi is allowed, command rejected."

If I delete the IP address of those SVIs, then I can to "send" those SVIs to the switch with no problem at all. But I need the SVIs to have IP address configured, since they are needed for routing Inter-V LAN traffic.
 
So, the question is: how can I route all the inter-VLAN traffic using just one SVI on the switch? Should I use the FWSM for inter-VLAN traffic routing?

View 15 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved