Cisco Switching/Routing :: Configuration PBR On Catalyst 4503
Mar 4, 2012i'm performing configuration PBR on catalyst 4503, but it doesn't work. [code]
View 21 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 4503 - Catalyst L3 Switch Model
Jan 9, 2012Currently we have cisco 4503 switch in one of our location without redundancy which servers below,
300 user (desktop & ip phones)
5 vlans
15 access switches are connected
one L3 connectivity.
Actually i want to understand is it really necessary to have 4503 or we can go for 4900 series as we are planning to have redundancy in distribution segment.
Which is the best L3 switch in the above scenario and how to measure the overall performance of the current 4503 switch...
Cisco Switching/Routing :: Catalyst 4503 - SSH Missing Cat4503 15.0 IPbase
May 18, 2013After deleting configuration with „write erase“ and reloading, our Cisco Catalyst 4503 with version cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin, and licence ipbase, doesn't recognize any command regarding SSH. We tried configuring SSH key with „crypto key generate“, but that command is not recognized either.
View 1 Replies View RelatedCisco Switching/Routing :: Cat4500-IPBASEK9-M / Catalyst 4503-E Linecard Support?
Mar 22, 2012I have a 4503-e with WS-X4013+TS supervisor and WS-X4548-GB-RJ45 card. I purchased a WS-X4648-RJ45-E card and installed but IOS says its unsupported. Supervisor is running 12.2(46)SG software and 12.2(31r)SGA firmware. Obviously I'm hoping this cars can be supported somehow. Do I need to upgrade software or firmware, or return the linecard and get equivalent supported card? Oh, system is running Catalyst 4500 L3 Switch Software. (cat4500-IPBASEK9-M)
View 6 Replies View RelatedCisco Switching/Routing :: Catalyst 6500 - DAI Configuration
Apr 26, 2012Any step-by-step configuration guide of how to enable DAI on Cisco Catalyst 6500 Series Switches.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 2960G Vlan Configuration?
Oct 24, 2011I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
Below is my startup configuration:
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
[code].....
Cisco Switching/Routing :: SPAN Configuration In Catalyst 3750
Dec 31, 2011I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control). I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8 (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.
View 5 Replies View RelatedCisco Switching/Routing :: WOL Configuration On L3 Catalyst 6500 And L2 2960G?
Dec 20, 2011I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
Layer 3 switch Intervlan routing configuration
ip forward-protocol udp 7
!
interface Vlan4
description vlan Client-WOL
ip address 172.22.51.253 255.255.254.0
ip access-group Deny_HTTP_Vlan1 in
ip helper-address 172.20.1.246
[code].....
After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.
Cisco Switching/Routing :: Catalyst Express 520 - Trunk Configuration?
Jul 11, 2012I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
1- data
100 - phones
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.
Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration
Apr 22, 2013I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
Civic_6506VSS#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
[Code].....
Cisco Switching/Routing :: Catalyst 3500 Fx Port Configuration
Jun 12, 2013I am connecting two catalyst 3500 XL switches via fiber fx ports for layer 2 connectivity. Do I need to configure anything in the IOS or do I just plug in the fiber?
What needs to be configured?
Cisco Switching/Routing :: Catalyst 3750 Failover Configuration
Jul 16, 2012Our servers are hosted at the Main site, site office A access to the Main site for Internet and servers. We are thinking NextG to take over when the link between sites goes down.
To start with, what is the configuration for 3750 at Site A and the Main site:
1) Trunking for both switches
2) Routing
3) the automatic failover configuration for the switch at Site A.
Cisco Switching/Routing :: WCCP Configuration On Catalyst 3750G?
Jul 5, 2010I have a WCCP Configuration on a Catalyst 3750G and a IronPort Webappliance. I have configured this situation many times before with cisco asa and ironport wsa, but with a switch, this is my first time.
VLAN 147 is a transportation vlan between the cisco switch and a hp coreswitch with the clients and servers behind the hp coreswitch.
VLAN 147 IP Address of the Catalyst is 172.30.47.1
IP of the IronPort Appliance is 172.30.47.10
IP of the HP Coreswitch is 172.30.47.2
Plan is to redirect the webtraffic coming from clients and servers from the 10.0.0.0/8 net behind the hp switch to the ironport wsa. In have configured these settings.
ip wccp web-cache group-list 15 password 7 091D1C5Aip wccp 80 redirect-list 16 group-list 15 password 7 14464058
interface GigabitEthernet1/0/22 description IRONPORT P1 BUWOG switchport access vlan 147 switchport mode access
interface Vlan115 ip address 172.30.15.2 255.255.255.0 standby 10 ip 172.30.15.1 standby 10 priority 90 standby 10 preempt standby 10 track Vlan115!interface Vlan147 ip address 172.30.47.1 255.255.255.0 ip wccp web-cache redirect in ip wccp 80 redirect in
[code]....
Cisco Switching/Routing :: Configuration Of Catalyst Express 500 Series?
Dec 25, 2012I was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 6506 Vlan-based Qos Configuration?
Feb 12, 2012I was unable to configure vlan-based qos on Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXH6, RELEASE SOFTWARE (fc1) Seems to me my configuration is not working. Here is the output of the interface:
sh int G1/6 | i rate
Queueing strategy: fifo
30 second input rate 25231000 bits/sec, 4282 packets/sec
30 second output rate 46940000 bits/sec, 9257 packets/sec
And here is my configuration:
interface Vlan3
ip address 192.168.1.1 255.255.252.0
service-policy input TEST_IN_PMAP
service-policy output TEST_OUT_PMAP
[code]....
Why I can't see matches in ACLs? I've double checked the direction and seems to me it is correct. I can't see matches even I configure something like this:
10 permit ip host 192.168.1.168 any
20 permit ip any host 192.168.1.168
Why my output rate is higher than 30M? Is it bacause there is no matching traffic here in ACLs? I'm absolutely shure that this host with such ip connected to this interface:
#sh arp | i 192.168.1.168
Internet 192.168.1.168 0 feed.beef.f00d ARPA Vlan3
#sh mac address-table | i feed.beef.f00d
* 3 feed.beef.f00d dynamic Yes 0 Gi1/6
Cisco Switching/Routing :: Catalyst 6509 - Ether Channel Configuration?
Dec 1, 2011I came across a Catalyst 6509 switch configuration and have noticed some strange thing on the ether channel configuration side, it appears that it have interface port-channel 2 and port-channel 2A, what was that mean? its the ether channel not forming and joined together?
What wrong with the below configuration that cause it to automatic created another port-channel (2A) interface in this case?
[code]...
Cisco Switching/Routing :: Catalyst 6513 - FWSM Module Configuration
Dec 20, 2007My company has acquired a Catalyst 6513 with a FWSM module installed on it. I have been reading lot of documentation on [URL], but still have some problems configuring the FWSM:
The 6513 has 10 SVIs configured, each of them with an IP address. These 10 SVIs are binded to 10 VLANs which I need to secure. These SVIs are used for routing all the Inter-VLAN traffic inside the switch. The documentation says it is recommended to use just one SVIs for connecting the switch to the FWSM, although you can use more than one using the command "firewall multiple-vlan-interfaces". I don't want to use this command because it seems a pretty more difficult configuration, since you have to use policy routing after using this command (or that is, at least, what documentation says).
When I try to "send" to the FWSM more than one VLAN that are configured as SVIs on the switch I get this error message:
"No more than one svi is allowed, command rejected."
If I delete the IP address of those SVIs, then I can to "send" those SVIs to the switch with no problem at all. But I need the SVIs to have IP address configured, since they are needed for routing Inter-V LAN traffic.
So, the question is: how can I route all the inter-VLAN traffic using just one SVI on the switch? Should I use the FWSM for inter-VLAN traffic routing?
Cisco Switching/Routing :: Force Catalyst 2960 To Ignore Startup Configuration?
Feb 4, 2013I was wondering if I can force catalyst 2960 to skip startup config stored in NVRAM and boot with no config everytime it is powered. I tried to find it on google and in cisco white papers but still no luck. I found only commands that begin with "set boot config-register ... ", but switch acts like it does not know these commands.
View 7 Replies View RelatedCisco Switching/Routing :: Configuration Module Supervisor Switch Catalyst 4500
Jun 4, 2012switch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Port Security Dynamic Configuration On Catalyst 3560xPOE
Oct 2, 2012I have connected a 10BaseT device to a CISCO Catalyst 3560xPOE switch with dynamic port security. All seems to work fine when the distance between the two devices is closer then 200ft. When I connect to 10BaseT devices farther out near 300ft the response from the attached device is lost. It works ok on unmanaged switches at the longer distance. Is there a minimum response time from attached devices for dynamic port security to work properly? Is there any other explanation why it would work on cheaper switches, but not on the Port Secured Switch?
View 2 Replies View RelatedCisco Switching/Routing :: IGMP Snooping Configuration For Multicasting On Catalyst 3020
Nov 24, 2011Our switch model is "Cisco Catalyst Blade Switch 3020 for HP" We are building HA (High Availability) Databases infrastructure.Currently, there are two nodes(hosts- servers) and two above switch for HA.
Oracle said we need to turn off the IGMP Snooping in order to use the multicasting for their interconnect communication.So my question is:
Q1> Is there any way to use Multicasting without turning off IGMP Snooping on Switch side?
Q2> If 'yes', how can we configure the switch for Multicasting ?
Oracle uses 230.0.1.0 & 224.0.0.251 IPs with 42000 range port for Multicasting communication.
Cisco Switching/Routing :: Catalyst 2960 / VLAN Configuration Using MS DHCP Server
Jan 28, 2013I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
Cisco :: Catalyst 4503 Doesn't Recognize Anything Plugged Into It
Oct 16, 2011just got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
Cisco Switching/Routing :: 4503 - How To Keep Ethernet Interface Up
Jan 18, 2012There is some way to increase the speed of changing the interface state from DOWN to UP when the cable is connected. I need to configure a port of Cisco 4503 in a way that when a cable is connected the port goes immediatly UP.
A solution can be to keep Cisco interface always UP and I remember that with "no keepalive" command to the interface configuration it was possible. But I tried and nothing happens.
Cisco Switching/Routing :: L2 Tunneling 4503 SUP2+TS?
Sep 16, 2012I need to implement over an ethernet link L2 tunnel because I want to isolate another VLANs domain.On the first side I can use the command : sw mo dot1q-tunnel on a new C4503 on the other side I cannot configure the command : sw mo dot1q-tunnel.
the other side is an old C4503 we upgrade the flash with a compact flash to upgrade to a new IOS v15 but the command doesn't exist also.I red the cisco feature navigator feature and I am sure the dot1Q-tunnel is available on my image : cat4500-ipbasek9-mz.150-2.SG.binso I don't know why I can use it.
Cisco Switching/Routing :: 4503 - Get Switch For Datacenter?
Feb 9, 2013We have microsoft servers and other application servers (around 12 in nos) which should have gig connections to the access switch. In turn this access switch will be connected to our distribution switch 4503. Which model of access switch best fits from the below 3 models. It should be cost effective as well.
WS-C2960 S-24PS-L
WS-C2960-24TS-L
WS-C3560G-24TS-S
Cisco Switching/Routing :: Logical SE/SVI Connection Between Brocade MLX And 4503
Jan 11, 2012I am installing a connection between Brocade MLX and Cisco 4503 using SE and SVI's. Below is the config for each. Am I missing anything like MTU Ignore or something along that nature?
*** Cisco 4503 (v15.01) Config ***
VLAN 35
name EOC_Gi1/2
[Code].....
Cisco Switching/Routing :: 4503-E Cannot Bring SFP Fiber Interfaces Up
Sep 2, 2012I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
Cisco Switching/Routing :: Duplex Mismatch Between 2950 And 4503
Jul 8, 2012I have a 4503 switch (in L2 mode) running 12.1 hooked into a C2950 running 12.1, using regular 4 pair Cat5e cables to connect between them. The 4503 has Gigabit port 2/1 trunking to the 2950's Fa port 0/13.
When I set the duplex mode to DUPLEX FULL and SPEED to SPEED 100 on both switches (for their trunk ports) the link fails, and my 4503 loses connectivity (since it gets it from the 2950).
Here is my config from the switches (per description):
The 4503:
interface GigabitEthernet2/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,100-140
[Code].....
Note, this is the only mode that works (which seems to work fine, but I get TERRIBLE throughput for anything that goes over the 2950.
Cisco Switching/Routing :: Boot 4503-E Switch From Secondary Image?
Sep 13, 2011We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies View RelatedCisco Switching/Routing :: 10G Line Cards Supported With 4503 SUP2+TS?
Nov 30, 2011I need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies View RelatedCisco Switching/Routing :: Very High CPU Utilization Core Switch 4503?
Feb 14, 2012We had a core switch(30 vlans) in our environment and it's noticed that CPU utilization of the core switch is showing high during recent days. I have checked logs and processes, but couldn't find the root cause. The issue found only in the office hourly only(after that the cpu utilization is idle and normal). I have already referred the following link to troubleshoot the issue " [URL]
see the following outputs from the core switch
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 6687557041432420936 466 47.52% 47.10% 45.98% 0 Cat4k Mgmt LoPri
55 30667074884269560256 0 45.36% 45.50% 45.85% 0 IP Input
29 28552856922870089254 0 3.59% 3.50% 3.57% 0 Cat4k Mgmt HiPri
[code]....
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
My queries regarding the issues are following
1) How can we find root cause regarding the high cpu utilization?
2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?
Cisco Switching/Routing :: Unable To Enable Netflow On Cat 4503-E (Sup7-E)
Dec 17, 2011I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....