Cisco Switching/Routing :: Catalyst 6500 - DAI Configuration

Apr 26, 2012

Any step-by-step configuration guide of how to enable DAI on Cisco Catalyst 6500 Series Switches.

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: WOL Configuration On L3 Catalyst 6500 And L2 2960G?

Dec 20, 2011

I got problem with wake on LAN software.. The software unable to ON all pc's remotely if sitting under different vlan. Everything is ok if using the same vlan. Below are the network diagram & switch configuration.
 
Layer 3 switch Intervlan routing configuration
  
ip forward-protocol udp 7
!
interface Vlan4
description vlan Client-WOL
ip address 172.22.51.253 255.255.254.0
ip access-group Deny_HTTP_Vlan1 in
ip helper-address 172.20.1.246

[code].....
 
After configured all the switches with the above setting, the software still cannot wake all the pc's using LAN. Base on sniffing, i can't find UDP port usage by the software. Attached here with print screen from wireshark.

View 7 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration

Apr 22, 2013

I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration  between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
 
Civic_6506VSS#sho mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE   

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 / QoS For Supervisor 2T?

Apr 30, 2013

I need to configure QoS (voice and video) for Catalyst 6500 series switches with Supervisor 2T modules and DFC4 linecards.
 
Is this radically different from what we do int he Sup32 and 720s? I was looking at some templates online, such as
 
[URL]
 
But I don't see anything for the new Supervisor 2T?

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Boot Process?

Mar 19, 2013

document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc

View 1 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Dual-Supervisor 720-10G-3C?

Sep 21, 2012

1. We now have SupA & SupB in the chassis, due to some mistake we have same IOS version but different feature set on them, although we configured redundancy mode sso, in the "show redundancy" we see Operating Redundancy Mode = rpr due to Software mismat, we now need to fix them as same feature set image, if I use "copy sup-bootdisk0:/xxxx slavesup-bootdisk0:/xxx", then write memory, does this cause any service/network interuption?

Available system uptime = 1 year, 1 week, 4 days, 9 hours, 21 minutes
Switchovers system experienced = 2
Standby failures = 0
Last switchover reason = active unit removed

[code]....
 
2. We did a failover test with this status, found that if we triggered supervisor failover, all modules will reload thus the services if interupped. How about after we make the Operating Redundancy Mode as sso, will this behaviour shows again? Or a stateful failover will happens, then modules no need reload?
 
3. We are using OSPF as our L3 routing protocol, after reference to the configuration, nsf should be enabled, we want to ask in the OSPF-domain nsf should be configured in all OSPF-enabled router or only 6500 which have dual-sup?
 
4. We also found that the interfaces(3 * Gig & 2 * TenG) in Standby supervisor cannot be use even enabled & configured, is it because we are running rpr mode now or will be the same even change to sso? Before customer have some older supervisor in 6500 non-e chassis, and they can use the standby supervisor interfaces as traffic forwarding, they use rpr-plus mode before, how about in sso mode?

View 6 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 BUS EoBC Channel

May 5, 2013

"How to display the EOBC error counters in the Catalyst 6500 series switches and a definition of the EOBC interface" document here on support forum stays that The Ethernet Out of Band Channel (EOBC) is a  half duplex channel that services many functions, which include the  Simple Network Management Protocol (SNMP) and the packets that are  destined for the switch.
 
Previously i were thinking that EoBC used only for SCP  and SLP protocol. In addition i found other article (but not on cisco site, heh) where stays that The Results bus is a       control plane, while the C (EoBC) bus is more of an       "admin plane", thus you will never see data       packets (such as CDP, SNMP, etc.) going over the R or C bus.
 
So there is a big contradiction between those two statements. How to prove one of those and if first one right, what meaned under the packets that are  destined for the switch in it? SCP and SLP or other traffic as well?

View 3 Replies View Related

Cisco Switching/Routing :: VPC On Nexus 5000 With Catalyst 6500 (no VSS)?

Jan 23, 2011

The diagram below is the configuration we are looking to deploy, that way because we do not have VSS on the 6500 switches so we can not create only one  Etherchannel to the 6500s.Our blades inserted on the UCS chassis  have INTEL dual port cards, so they do not support full failover.
 
Questions I have are.

- Is this my best deployment choice?
- vPC highly depend on the management interface on the Nexus 5000 for the keep alive peer monitoring, so what is going to happen if the vPC brakes due to:
- one of the 6500 goes down
- STP?
- What is going to happend with the Etherchannels on the remaining  6500?
- the Management interface goes down for any other reason
- which one is going to be the primary NEXUS?
 
Below is the list of devices involved and the configuration for the Nexus 5000 and 65000. 
 
Devices

·         2  Cisco Catalyst with two WS-SUP720-3B each (no VSS)
·         2 Cisco Nexus 5010
·         2 Cisco UCS 6120xp
·         2 UCS Chassis
     -    4  Cisco  B200-M1 blades (2 each chassis)
          - Dual 10Gb Intel card (1 per blade)
 
vPC Configuration on Nexus 5000
 
TACSWN01
TACSWN02
feature vpc
vpc domain 5
reload restore
reload restore   delay 300

[code]...

View 22 Replies View Related

Cisco Switching/Routing :: Catalyst 4500 Or 6500 VSS Capabilities?

Dec 10, 2012

Catalyst 4500 or 6500 VSS Capabilities?

View 6 Replies View Related

Cisco Switching/Routing :: 6500 - FTTx (FTTB) On Catalyst?

Dec 15, 2011

Its possible FTTx on a 6500 ?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Switch Architecture

Jul 16, 2012

one of the most widely deployed switches in the world. The "Swiss Army knife of network", can do routing, switching, security, wireless and almost everything that you would want your core switch to do. Remember to use the rating system to let Akshay know if you have received an adequate response. 
 
Akshay might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Network Infrastructure sub-community LAN, Switching and Routing discussion forum shortly after the event.  This event lasts through July 27, 2012. Visit this forum often to view responses to your questions and the questions of other community members.

View 22 Replies View Related

Cisco Switching/Routing :: How To Identify Modules Supported By Catalyst 6500

Nov 15, 2011

how to identify which modules are supported by cisco catalyst 6500. is there any OID which can give us the information

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 - Crash Due To Pid 234 - Process ACE HAPI

Jun 29, 2012

I want to know what is this process used for on a catalyst 6500 ? we have got following message in the crash file, probably due to CSCsv77354
  
Jun 30 16:06:47.099 UAE: %SYS-6-STACKLOW: Stack for process ACE HAPI running low, 0/6000

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Update And HTTP Server?

Mar 24, 2013

cisco WS-C6509-E Core switch with IOS  "s72033-ipservicesk9_wan-mz.122-18.SXF11"
 
i have 2 question 
 
Q.1 i want to upgrade this switch what is the latest IOS ver. supported by this module ?
 
Q.2  i need to enable http server on this switch when i run this comman it's accsebt but i cant get http work

View 1 Replies View Related

Cisco Switching/Routing :: To Issue Eigrp Leaking Routes On Catalyst 6500

Mar 26, 2012

Is it possible to issue eigrp leaking routes on catalyst 6500 running IOS 12.2-33SXI9 on gigabitethernet interfaces? or is there another way to acomplish this?

View 10 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 / Port-Channel Down But Correctly Configured

May 23, 2012

I has a issue about etherchannel beetwen 02 Catalyst 6500 switch, i need your comment about it. if you had any similar experience:
 
1.- On Catalyst Switch 6500-1:   I configured interface port-channel 4 and associated it to G6/29 and G6/30 interface Port-channel4description IUU1_Gn1_HLIMSGSN01_Port_channel_6_29_6_30switchportswitchport trunk encapsulation dot1qswitchport trunk allowed vlan 406,408switchport mode trunkswitchport nonegotiatelogging event link-statusload-interval 30mls qos vlan-basedmls qos trust dscp!

2.- On Catalyst Switch 6500-2:  I configured interface port-channel 4 and associated it to G6/29 and G6/30
 
interface Port-channel4
description IUU2_Gn2_HLIMSGSN01_Port_channel_6_29_6_30
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 407,409

[code]....
 
and i see output "show interface Po4A" up up on switch-1, "show interface Po4B" up up on switch-2   
 
5.- In the show running-config not appear configured Po4A and Po4B. it only show on outputs
 
6.- Po4A and Po4 was not configured on neither switches, my question is why appear Po4A and Po4B on switch-1 and switch-2 respectively?  and why Po4 appear in down down.
 
7.- I solved this issue by shutdown and not shutdown to the interfaces on both routers, currently all is OK.

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 - Netflow Table Utilization Logs

Nov 27, 2011

We are getting log messages like

%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 95%
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 99%
 
What this messages really means and how to get rid of these messages. We are using IOS version 12.2(33)SXJ in Catalyst 6500.

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Supervisors Differences Sup1A Vs Sup32

Feb 16, 2012

I understand that my questions seems to be rather strange cos supervisors is rather old (Sup1A especially). But i am interested in understanding what puprpose were in production SUP32. I cant find out enough differencies between Sup1A with MSFC2 and Sup32 to understand what reasons lead to deploying new sup in none fabric supervisor series.

Both supervisors have same perfomance - 15Mpps and have limitation on backplane bandwith of 32 Gbps (cos both use swithing bus), both supervisors equipped with MSFC2 and etc. Differencies i found:

SUP 32 have 10Gbe ports support (but this seems to be doubtful enhancement -  with it perfomance GE ports seems to be more appropriate technology isnt it?) SUP1A equipped with PFC, SUP32 with PFC3BSUP32 deploys CEF (what is benefit of CEF if perfomance same?) 

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 - Cannot See Return Traffic On SPAN Session?

Jan 31, 2012

On a Catalyst 6500, we configured a SPAN session with VLAN 300 as a source. We configured the session bi-directional ("both" keyword). We connect a sniffer on the SPAN destination port.
 
Strangely enough, we only see the traffic from the VRF to the firewall, but not the reverse traffic ! What can be the problem ?

View 2 Replies View Related

Cisco Routing :: Catalyst 6500 / 4500 - Preventative Maintenance On Catalyst Chassis Switches?

Jun 4, 2013

Are there any best practices for preventative maintenance on Catalyst Chassis switches.  Looking to build a PMI schedule for a customer.  Or is there evidence not to perform it at all.  Things like re-seating line cards, cleaning fan exhausts, etc. 

View 1 Replies View Related

Cisco Switching/Routing :: Does Supervisor 720 Support All Existing Catalyst 6500 Series Interface

Feb 12, 2013

Q. Does the Supervisor 720 support all existing Cisco Catalyst 6500 series  interface and services module, protecting customer investments?

View 1 Replies View Related

Cisco Switching/Routing :: ERSPAN Source On Nexus 5548 And Destination On Catalyst 6500

Aug 9, 2012

I'm trying to get ERSPAN working with an ERSPAN source on a Nexus 5548 and the ERSPAN destination on a Catalyst 6500.
 
The configuration on the Nexus is as follows:
 
[...]
interface loopback0
ip address 192.168.2.133/32

[Code].....
 
If I do a netdr capture I can see ERSPAN traffic sourced from the Nexus reaching the C6500, but there doesn't appear to be anything sent out the ERSPAN destination inerface (Gi4/6) and there's nothing being received by the probe connected to that interface. I know the traffic seen with netdr is definitely the ERSPAN traffic sourced from the Nexus as I've changed the TTL and DSCP values within the monitor session on the Nexus and can see those changes reflected on the C6500 netdr capture. The attached is a screen grab of the show netdr capture started with debug netdr capture soure-ip-address 192.168.2.133.
 
When I look at the interface I see it shown as up/down (monitoring), but no output or counters clocking up. If I run a local SPAN session on the C6500 it works fine.
 
I've tried changing the destination IP address from that assigned to the C6500 Loopback interface to an IP address assigned to a physical interface, but that still doens't work.
 
The hardware in the C6500 is WS-SUP720-BASE Hw version 3.2 with WS-F6K-PFC3B Hw version 2.4. The IOS version is 12.2(33)SXI6.

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Switch Support Multi-chassis EtherChannel Features?

Sep 26, 2012

I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly  stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?

View 4 Replies View Related

Cisco Switching/Routing :: Configuration PBR On Catalyst 4503

Mar 4, 2012

i'm performing configuration PBR on catalyst 4503, but it doesn't work. [code]

View 21 Replies View Related

Cisco Switching/Routing :: 6500 - Campus OSPF Configuration

Aug 26, 2012

I manage a small/medium sized campus network consisting of 4 Cisco 6500 series chassis (each with SUP720's) and a couple hundred Cisco 3550/3560/2960 edge switches. We recently completed a new leg of fiber that will make a completed loop between all of the 6500's .... before I make the pyhsical connection I need to figure out my OSPF entries on each 6500 switch.

View 4 Replies View Related

Cisco Switching/Routing :: 6500 Changing Switch Configuration

Aug 27, 2012

I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !

View 3 Replies View Related

Cisco Switching/Routing :: Best Configuration Between Vmware ESX Server 6500

Dec 6, 2012

what is the best configuration between vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200.

View 6 Replies View Related

Cisco Switching/Routing :: 6500 - Dot1ad Global Configuration

Apr 3, 2012

I am facing problem about dot1ad global configuration command and my topology is here;
 
Notebook >> (access vlan 100) SW2960 (trunk)>> (trunk) C6500
 
First time I have create SVI interface on C6500 and enable trunk on interface that connected to SW2960 and SW2960 assigned access vlan 100 on port connected to Notebook. Then I tried to ping from Notebook to C6500 on SVI100 which work fine.
 
Second time I tried to enable MST on C6500 and after that everything still working and I can ping from Notebook to SVI100 on C6500.
 
Third time I tried on turn on dot1ad in global configuration mode and from now I can't ping from Notebook to C6500.
 
Forth time I tried to disable dot1ad from global configuration by "no dot1ad" command and then I can ping.
 
My intention is I would like to do EVC which require dot1ad in global configuration but I stuck in third step and don't know what's does it mean for this command and how I can resolve this issue?
 
Information on C6500
IOS Software (s2t54-ADVENTERPRISEK9-M), Version 15.0(1)SY1
Processor     SUP-2T
Linecard       WS-X6824-SFP

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 2960G Vlan Configuration?

Oct 24, 2011

I have got a catalyst cisco 2960G series switch and via this switch I want to creat serveral vlans. I am getting a dhcp IP from a router and I want to setup my own vlan networks.
 
I plugged in the Ethernet cable that came from the dhcp router to port 16 of the cisco switch and configured the ports 1,2 and 3 for vlan 1, 2 and 3
 
the dhcp router has given me this IP 192.168.10.158 defautl gateway is : 192.168.10.1
 
when I plug in a PC to port 1 or 2 of the cisco switch I still receiving the IP from range 192.168.10.* but not from the range that I configured for the vlan 1 or 2.
 
Below is my startup configuration:
 
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id

[code].....

View 28 Replies View Related

Cisco Switching/Routing :: SPAN Configuration In Catalyst 3750

Dec 31, 2011

I have CISCO catalyst with VLANs (VLAN ID 33, 36, 40-53) configured. I need to configure port mirroring in Switch 3750 for NAC (Network Access Control).  I need to Monitor all the VLANs. Here is the SPAN configuration of switch: [code] Monitor session 1 source vlan 33 , 36 , 40 – 53.Monitor Session 1 destination interface fa 1/0/8  (here I am not able to set encapsulation dot1q ) because the error occurred saying %one or more dest port do not support the encapsulation%.

View 5 Replies View Related

Cisco Switching/Routing :: Catalyst Express 520 - Trunk Configuration?

Jul 11, 2012

I am struggling with a CE520 and its smartports stuff.I have configured the following vlans :
 
1- data
100 - phones
 
I need to bring those vlans (both of them) to a Cisco 800 router. The port of the 800 router is already configured as trunk and accepts vlan 1 and 100.The cisco 800 has both vlan 1 and 100 configured with 2 ips on different subnets, and ip routing is enable (to route between two vlans). Also, no access lists are configured.I have configured one port in the switch as role "router" and connected to the router. The other ports are all configured as phone-desktop (phone vlan 100 desktop vlan 1).If I connect a phone and manually configure an ip (the phone gets automatically vlan 100), and try to ping the phone from the router, it doesnt respond. Alse vlan 100 is protocol down.I am guessing what s the right configuration as the link between the switch and the router should be a trunk link for 1 and 100 vlans, but it looks like is transporting only vlan 1.Also changing the port role to "other" when you can specify the native vlan and another vlan, the switch doesnt accept vlan 100 as additional vlan on that link.

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3500 Fx Port Configuration

Jun 12, 2013

I am connecting two catalyst 3500 XL switches via fiber fx ports for layer 2 connectivity. Do I need to configure anything in the IOS or do I just plug in the fiber?
 
What needs to be configured?

View 2 Replies View Related

Cisco Switching/Routing :: Catalyst 3750 Failover Configuration

Jul 16, 2012

Our servers are hosted at the Main site, site office A access to the Main site for Internet and servers. We are thinking NextG to take over when the link between sites goes down.
 
To start with, what is the configuration for 3750 at Site A and the Main site:

1) Trunking for both switches

2) Routing

3) the automatic failover configuration for the switch at Site A.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved