I have newly purchased Cisco 887 Router. I am trying to replace this router with the exisiting ISP provided modem I am facing an issue to bring the ATM0 port up.
Here is my router config
hostname Internet Router
!
boot-start-marker
boot-end-marker
!
!
no logging buffered
[code]....
We did an upgrade from NX-OS 5.1.5 to 5.2.4 and found all M1 line card interfaces were stuck in initializing state for long time.'show module' status says ok. And we cannot execute shut/no shut command under the interface. N7K-M108X2-12L & N7K-M148GT-11 are the two M series cards. Only option was to downgrade back for the time being.
N7K01# sh int e1/1 | in down
Ethernet1/1 is down (initializing)
Is the ADSL line interface on Cisco 877W not initialising a known issue? This interface on my router has been in this state for more than one month, with the rest of the router seemingly operational. The interface was connected directly to my ADSL broadband and worked well for two years. But then, about a month ago, the interface went down. I saw the exact moment this happened recorded as a syslog message. The only information was that the interface status had changed to down.
Initially I thought this was a matter of reload the router and all will be well. Did not happen. Then I thought my broadband connection was to blame. However, this option was quickly ruled out. So I went on to exhaust all troubleshooting options, including reflashing the router with the saved image and totally changing the configuration. Still no change. I have had to go back to my old BT home hub for internet access. In terms of speed this actually works a lot better than the Cisco router. But I would still rather have the router connected to my broadband line. What can I do to bring the ADSL interface back to life?
I have a couple of 3560 switches running c3560-advipservicesk9-mz.122-44 and they are randomly experiencing the following:
- The switch locks up with no preceding error message in the log (I am forwarding syslog to Splunk).
- Upon reboot, the switch goes through the normal startup sequence with no error messages, then for some reason reloads the flash and starts all over again. (refer to doc)
This could happen after days or weeks. Sometimes they will go through two of these reloads on boot and be fine for awhile, and other times they will be stuck in the loop infinitely. I am using this same image with all of our 3560s, but am only having this issue with two of them.
Could you explain me what "interface ATM0" is ? Is it virtual interface or physical ? And in this configuration ATM stands for Asynchronous Transfer Mode or anything else?
View 11 Replies View RelatedI have been trying to configure a 837 for a while now and I'm finally nearly there. So far the tests run(SDM interface test) and pass on atm0(WAN connection to the internet) but not on ethernet0. I am guessing i need to link them somehow but since I don't know the terminology searching for how to do it is turning out to be difficult.
Here is my config:
!This is the running config of the router: 192.168.0.1
!----------------------------------------------------------------------------
!version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
I tried ip route 0.0.0.0 0.0.0.0 Dialer0 first with no luck to i added the ip route 0.0.0.0 0.0.0.0 ATM0 still nothing?
On the ATM0 interface on a 877 do you have to configure the bandwidth or will the router automatically negotiate this ? Also is the bandwidth command in relation to the upstream or downstream bandwidth?. We currently specify bandwidth 448 which matches the upstream.
View 3 Replies View RelatedI have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies View RelatedI had a working server running ISE version 1.1.0.665 but someone in the build room decided to pull the power out of the server rather than shutting it down correctly. I have booted the server back up however the web management page was not accessable. I have checked the server status and the end result is the Application Server in the "still initializing" stage. I have left the server for several hours and the status has not changed.
I know people have previously run into this issue but no one has posted any resolution or confirmed that a rebuild is the only solution. I have tried to create an on-demand backup but it seems to fail when attempting to provide the credentials (which are correct) for the FTP server.
I have 5 to 6 878 routers and in all these routers the ATM interface is stuck up with initializing mode. This is the IOS running on it c870- advipservicesk9-mz. 124-15.T9.bin
View 1 Replies View RelatedWe upgraded a CSACS-1121 from ACS 5.2 to ACS 5.4 with CLI Application upgrade ACS_5.4.0.46.0a.tar.gz FTP After ACS reboot, services never start... After 15 hours, we always get same message:
ACS/admin# show application status acs
Application initializing...
Status is not yet available.
Please check again in a minute.
We installed patch 5-4-0-46-2.tar.gpg but we got same issue for 2 hours ...What could I do?
I have two ASA 5505 running 8.4 and I tried using the VPN wizard and using the CLI but i am not able to get the peers to initialze. I have looked at other configs and am not seeing what is missing. I have tried packet tracking through the ASDM and its not even seeing the VPN tunnel and keeps trying to go out to the internet.
View 5 Replies View RelatedI am buying a Nexus 5K (N5K-C5548UP-FA) with the layer 3 card (N55-D160L3 - Nexus 5548 Layer 3 - Daughter Card).The switching capacity of it is 960 Gbps but I know I should expect less doing the Layer 3 function (it will only be used with static routing).What switching/routing capacity should I expect? How can I estimate it? What else should I consider?
View 1 Replies View Relatedwe've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedI am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
I would like to know if Catalyst WS-C3750G-48TS-E recognizes and understand Cisco VSS ( Virtual Switching System) . Is there a List available which tells us which Old Catalyst Switches or current switches understand Cisco VSS?
View 3 Replies View RelatedWe are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedI have the following devices :
-1 VM Host
-2 Layer 3 switches
I would like to provide full redundancy for all vlans being used by VM Guests on the VM Host as well as the management vlan being used by the VM Host.I have created two LACP etherchannel connections on the VM Host. Each etherchannel from the host consists of 4 ports spanning a single NIC. One etherchannel connection goes to a trunked etherchannel connection on switch 1, and the other etherchannel connection goes to a trunked etherchannel connection on switch 2.Switch 1 and switch 2 have an etherchannel connection between them that carries all of the vlans in the topology.Vlan 2 is the managment vlan. Vlans 3, 4, and 5 are vlans that VM guest systems will be using for normal data traffic.
I intend to use switch 1 as the VRRP active router and spanning-tree root bridge for vlans 2 and 3.I intend to use switch 2 as the VRRP active router and spanning-tree root bridge for vlans 4 and 5.The spanning-tree configuration is using multiple spanning-tree with two instances. Instance 1 has vlans 2 and 3 associated and Instance 2 has vlans 4 and 5 associated. I would like to have this topology be fault tolerant to the point where if one of the etherchannel links between the host and one of the switches goes down, (for example, if switch 1 was powered off) traffic will be automatically redirected through the other functional link. I believe that my VRRP configuration would allow for a fairly quick failover of layer 3 services, but I am not certain that my design will be functional at a layer 2 level.
What I am uncertain about is how spanning-tree will converge. I am assuming that the virtual switch on the VM host will not be forwarding any BPDUs being sent by either switch. Would either of the links connecting to the host be considered a redundant link by either switch?Would the link between switch 2 and the host be inactive for all vlans in MST instance 1 during normal operation?Conversely, would the link between switch 1 and the host be inactive for all vlans in MST instance 2 during normal operation? Would all links remain active for ALL vlans? Would this mean that some traffic may travel through switch 2 to reach switch 1 instead of going directly to switch 1?
As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedIt is said that the switching fabric of WS-C3750X-24T-E is 160Gbps.Could any body tell me what is switching fabric, any relevance or difference from forwarding rate?,Is there any document to know how will the switch reach the 160Gbps full switching fabric performance?
View 5 Replies View RelatedI got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
It is understood that sub-50 ms ERPS convergence can be achieved with certain HW/SW combinations.
1) What are the platforms supported (and with what FW/SW) has this been tested ?any results that can be shared?
2) Link failure detection in GigE on Copper is slower compared to GigE over "pure" Fibre; so no sub-50ms would be possible with Copper ring ports.is sub-50ms convergence achievable with "combo SFP ports" ?
Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies View RelatedMy management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
Why Cisco implements so much switching capacity in their switches Obviously,16 Gbps of permutation performance is too much for the 8,8 Gbits (24*200+2*2000) needed by ports so why they put so many bandwidth?
View 3 Replies View RelatedThe have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
We are setting up a test lab in our DMZ. The path to the internet is basically like this. Anything past the firewall is irrelevant. For this lab lets assume it is vlan 300.
LAB SW ---> DMZ-SW ---> ASA FW ---> INTERNET
LAB IP Range = 172.16.300.0 /24
GW = 172.16.300.1 (On FW int)
Trunked all the way through.
I have an int vlan set up on the LAB SW. It is being trunked to DMZ SW. DMZ trunks it to ASA FW where there is a failover with a redundant switch.On the ASA the interface 0/2 is a subinterface 0/2.300 being used as the default gateway.
I have DHCP running in a specific range on the LAB SW and do get an ip address when plugged in. I cannot ping the default gateway on the ASA FW.The GW is defined using default-router command for 172.16.300.1 i.e. default-router 172.16.300.1?
We are running ospf on the firewall. There appears to be a pattern with ospf and a similar subnet setup elsewhere. I was wondering based off of this info would configuring ospf for 172.16.300.0/24 allow me to ping the GW from a client on the LAB SW.Secondly. I trunked 300 on the DMZ SW but I didnt add the vlan to the configuration. i.e. conf t <enter> vlan 300 <enter> Does this really matter? Or is having the vlan in the configuration only pertain to access mode on interfaces?
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
View 2 Replies View RelatedI have the network described below, on which I am running PIM.
(network) ---- Embedded Linux Router --(vlan 5)-- CAT 3560G --(vlan 5)-- Cisco 1811 Router ---- Multicast Listener
The Linux Router and the 1811 have formed a PIM neighbor relationship. The multicast listener sends an IGMP Join and I can see the PIM join leave the 1811 router (via "debug ip pim"). Using tcpdump on my linux router I never see the Join come in, but I can see the PIM Hellos (which is why the neighbor relationship formed).
some of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies View Related