Cisco Switching/Routing :: 1921-SEC/K9 - HWIC-4ESW Compatibility
Jan 9, 2012Does Cisco 1921-SEC/K9 support HWIC-4ESW ? I require 4 x 10/100 Ethernet ports
If yes how many ? are there any drawbacks if i use this module instead of a switch?
ADVERTISEMENT
Cisco Switching/Routing :: Trunking With HWIC-4ESW On 1921?
Feb 27, 2012We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
View 4 Replies View RelatedCisco Switching/Routing :: HWIC 4ESW - Cannot Ping It
Dec 28, 2011I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
View 3 Replies View RelatedCisco Switching/Routing :: Making Etherchannel On A 4ESW HWIC
Nov 4, 2012Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedCisco Switching/Routing :: Two Cards HWIC-4ESW On C3845?
Nov 18, 2012We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
the configuration is the folowing
interface FastEthernet0/0/0
switchport access vlan 100
speed 100
[Code].....
Cisco Switching/Routing :: HWIC-2FE And 2811 Compatibility?
Jan 24, 2013Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies View RelatedCisco Switching/Routing :: Not Detecting HWIC-2T In 1921 Router?
Oct 15, 2012I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......
Slap An HWIC - 4ESW Into A Router
May 9, 2012meaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?
View 6 Replies View RelatedCisco WAN :: Hwic-4ESW 2 Unit On Chassis?
Mar 18, 2012i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Replies View RelatedCisco WAN :: Can't Put A Second HWIC-4ESW In A 3825 Router And Don't Work
Aug 4, 2012I put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...
View 1 Replies View RelatedCisco WAN :: Not Able To See HSRP Configuration Option For HWIC-4ESW
Jun 12, 2013I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies View RelatedCisco WAN :: 2811 WAN Link Terminated In HWIC-4ESW
Jun 3, 2013I have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
View 4 Replies View RelatedCisco Infrastructure :: Use HWIC-4ESW As No Switch Port?
Oct 4, 2012Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies View RelatedCisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?
Sep 2, 2011How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies View RelatedCisco WAN :: Apply MQC On 4 Port HWIC-4ESW - 3845 Router?
Mar 24, 2011I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
Cisco WAN :: Test A MPLS Capability With1841 Router And HWIC-4ESW
Oct 11, 2012We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
View 1 Replies View RelatedCisco WAN :: Configure Newly Installed HWIC-4ESW On 2811 Router To Bridge To FE 0 / 0 Interface
Apr 20, 2012I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedCisco Switching/Routing :: IP SLA Support On 1921/K9 Or 1921-SEC/K9?
Oct 5, 2012We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
Cisco WAN :: HWIC 4ESW Need To Configure Point To Point Data Dual Leased Lines
Jan 18, 2012We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedCisco WAN :: HWIC-1FE And Ios Version Compatibility On 2811?
Sep 7, 2009I would like to ask if a cisco 2811 running on an ios c2800nm-adventerprisek9-mz.124-25a.bin should be able to make an HWIC-1FE card work? I am also not detecting the card on any show commands. Plus i am seeing that all the LEDs (FDX/COL,100 and LINK/ACT) are lit steadily even though there is no cable attached to it, is it safe to say that the card could be defective?
View 6 Replies View RelatedCisco WAN :: 1921 With HWIC-3G-CDMA To Concentrator 3005?
Mar 29, 2011I have an interesting problem. I've configured a site to site VPN connection between these two devices. I am using the CDMA card as the primary and only outside connection on the 1921. What happens is that by default the cellular connection is offline. When traffic is generated internally from that network to the concentrator side of this scenario the cellular connection goes online and builds the tunnel, no problem. However, I cannot initiate the tunnel from the concentrator side. I think what i need is a way to force the cellular connection to always be on, and if it fails to come back online.
View 3 Replies View RelatedCisco WAN :: Hwic-3g-hspa 1921 Giving Time Out
Jun 15, 2011I've been using hwic-3g-hspa with 1841 before but now I'm using 1921 and I'm always getting timed-out
View 1 Replies View RelatedCisco WAN :: Cross Connect Between 2821 With WIC-2T To 1921 With HWIC-2T
Nov 13, 2012i have 2 routers 2821 with wic-2t serical card and 1921 with hwic-2t serial card.can i connect between those two serials card with serial cross cable ?
View 3 Replies View RelatedCisco Switching/Routing :: 1721 WIC-4ESW Cannot Get BVI To Work
Mar 11, 2012I started to set up a 1721 router with WIC-4ESW. This is on an internal network, so only looking to just do routing from FA/0's interface to the networks attached to ports on the WIC. I first assigned just VLANs to 2 of the ports and this did not work. So I did some reading up and decided to use bridge groups. Except I still can not access the interfaces on the WIC. And by that I mean on the router itself I can not ping the ip assigned to the BVI.
I have another 1721 w/4 port that long ago I seem to remember simply assigning VLANs to the interfaces and I was able to communicate between the networks without issue (or maybe I just don't rememer that well). Thing is I should be able to at least ping the internal interfaces shouldn't I (assuming the status is up). I don't know why BVI2 and 3 are listed as down, nor do I seem to know how to bring these up.
This is what ip int br gives me:
1721#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI2 192.168.101.1 YES manual down down
[Code]....
Cisco WAN :: 1921 / 1941 - Unable To See HWIC-1DSU-56K4?
Aug 4, 2011We are currently moving from 1841 (EOL) to 1921/1941 routers. According to the module support doc [URL] this HWIC-1DSU-56K4 card is supported. We have tried both the 1921 and 1941 with the cards without any luck.
IOS Verison: c1900-universalk9-mz.SPA.152-1.T.bin
System Version: 15.0(1r)M9
Boot Error: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/1 has an unknown id 0xB
Show Diag:
WIC Slot 1:
DSU 56K
WIC module not supported/disabled in this slot
Hardware revision 1.0 Board revision A0
[code].....
Cisco WAN :: 1921 - Connect Switches Via Fiber / How To Configure HWIC
Oct 30, 2011we bought the Cisco 1921 ISR with the HWIC-1GE-SFP to get a router that would be able to connect via fiber to our switches. I called Cisco and their reps recommended this router/HWIC pair to me.
I have got the basic configuration out of the way and I have discovered my router with CCP, now I would like to know how I can configure this HWIC. I have the SFP(GLC-SX-MM= ) installed correctly and it is connected to our test switch via an LC/LC cable, but when I do 'show ip interface" all ports are down except the one my workstation connects directly to the router with (gigabit0/1).
Cisco Switching/Routing :: Inserting 2 ZHWIC 4ESW In 2911/K9
Jul 8, 2012We have cisco 2911/k9 we fixed 2 HWIC-4ESW crds in 2911. I create 4 vlan i have assigned 1 HWIC-4ESW all vlans are working fine
when i configure 5 th vlan it assigned second HWIC-4ESW 1 port but interface status showing up. i connected one system to that port i try
to ping that port that port notable to pinging is there any activation for that second HWIC-4ESW.
Cisco Switching/Routing :: Any Configuration Guide For EHWIC-4ESW Card
Jul 18, 2012Any configuration guide for EHWIC-4ESW card. Also the difference in configuration between EHWIC-4ESWG and HWIC-4ESW if any?
View 1 Replies View RelatedCisco Switching/Routing :: HWIC-4T1/E1 Support On A 2811?
Oct 31, 2010[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies View RelatedCisco Switching/Routing :: Compatibility Between 887VAM-W-E-K9 And 800-IL-PM2?
Jun 13, 2012Are 887VAM-W-E-K9 and 800-IL-PM2 compatible? We have got both of them but it seems that router has a 30W power source and module has a 80W power source.
View 1 Replies View RelatedCisco Switching/Routing :: WS-X6748-GE-TX And SUP-2T Compatibility?
May 13, 2013I have a WS-X6748-GE-TX with the WS-F6700-CFC daughter card. Is it possible to replace the WS-F6700-CFC daughter card with a WS-F6K-DFC4-AXL to make this compatible with the SUP-2T? Or, are there differences between the CFC and DFC base modules?
View 11 Replies View RelatedCisco Switching/Routing :: CAT 6509 STP Compatibility With F5 LTM
Sep 1, 2012We have connected a single F5 box with dual links to 2 different Cisco Catalyst switches using 802.1Q trunks. F5 is configured with RSTP mode and on Cisco Switch RPVST+ is configured.STP root bridge is hardcoded on the Cisco side. Loop Guard is globally enabled.On F5 STP link type is Auto, STP Edge port is disabled since that port is connected to the cisco switch.When we are failing over the F5 primary link to the secondary link we see 'Loop Inconsistent' on the cisco switch and things dont work after the failover.We have tried configuring the F5 as STP passthrough but that doesn't fix out the issue.I have checked out the forums and found out following recommendations
1. Configuring MSTP bw F5 and Cisco for better compatibility (Not possible from Cisco side because of a major change in large production setup)
2. Configuring VSS in Cisco switches (not possible due to hardware limitation)
3. Connecting F5 using single links to each switch (redundancy compromised)
I am wondering that on which default vlan does the F5 STP instance0 sends the STP BPDUs ? the term used on Cisco side is native vlan and others use PVIDs; that F5 default vlan should match the native vlan on cisco trunk side.
Cisco Switching/Routing :: 1921 Routing Access From Mixed IP Ranges Between VLANS
Jan 23, 2013I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]