Cisco WAN :: Apply MQC On 4 Port HWIC-4ESW - 3845 Router?
Mar 24, 2011
I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
I put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
I have a 2811 ISR, a lab unit with almost nothing yet configured other than some IP networks on serial and FE interfaces to ping to other lab routers. And I have one HWIC-4ESW installed, and I amrunning IOS 15.2.I want to set the card as a single routable interface and just have the ports act like switch ports, which I imagine is the default design of these cardsI work a lot with Cisco 891 ISRs so figured it's the same here, assign an IP to interface Vlan1 and all is well. That was wrong, obviously more config is required.It seems there are a lot of differing answers out there, so far none what worked for me. The best looking one I could find said to assign an IP to the Vlan 1 interface, then go to each of the four FE interfaces on the switch module.
I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
I have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
Maybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
We have been facing a problem at my company ! We have a Cisco Router 1921 with one HWIC-4ESW in trunking with a RuggedCom switch RSG2100.When I use the GigabitEthernet port to make a trunk, I create 2 sub-interfaces (one for each Vlan) and configure the Port on Switch as Trunk, the inter-VLan routing works with no problem.But now I need to use this configuration using the HWIC-4ESW on Router, and I can't do this work. I try creat interface Vlan for each vlan, and try creating the VLans at Router Vlans database, but no way. At router I enter in interface and try to do the switchport trunk command to add a Vlan, but doesn't work.
We have two cards HWIC-4ESW on router 3845 but we need that the two cards 8 ports conected betwen, if a pc on port 1 can ping a pc conected on port 8 on second card. tis comunication can,t doing a pc on port 1 can,t conected a pc on port 8.
In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0 %HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted Interface IP-Address OK? Method Status Protocol GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0: Unknown WAN daughter card WIC module not supported/disabled in this slot Hardware Revision : 2.0 Top Assy. Part Number : 800-27738-02 Part Number : 73-10677-02 Board Revision : B0 Deviation Number : 0 Fab Version : 02 PCB Serial Number : FOC******** RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : HWIC-2FE Version Identifier : V01 CLEI Code : COUIAFUCAA Base MAC Address : 001a.6c70.260b MAC Address block size : 2 Connector Type : 01 EEPROM format version 4 EEPROM contents (hex):(code)
I faced a strage issue as one of our router port cable was removed from the router port but the Port status is showing as up /up which made our HSRP state to active active causing an outage , The router we are usign is cisco 3845 and IOS is c3845-adventerprisek9-mz.124-8b.bin
I´m a IOS CLI fanatic. Its the first tiem that I have to configure a SB switch. Its very confusing, I want setup a voice vlan id as 200. but I don see that this value change when I try to apply the smartport macro to the interface.Its possible change a smartport macro?
I am facing problem with ACE configuration. I want to redirect 443 traffic to my Proxy Server. But I am not able to do this. I want to redirect only subnet 192.168.80.0/24..Then only it is working but I dont have to have this policy to be applied on all the users only one subnet I want to have under HTTPS policy.
how can I apply the policy only on specific subnet so that port 443 traffic can be redirect and rest of all subnets can go direclty to Internet.
I have a 4510R-E chassis with SUP7-E running IOS XE version 3.01.01.SG. I am unable to create a port-channel and apply auto-qos for VOIP.If I configure auto-qos on the physical interfaces, I get this message when I try adding them to the port channel:
"The attached policymap is not suitable for member either due to non-queuing actions or due to type of classmap filters."
Auto-qos is not an available command in the port-channel interface configuration, but if I try adding the service policies that were created by auto-qos to the port channel manually, it lets me apply the input policy but on the output policy I get this message:
"A service-policy with queuing actions can be attached in output direction only on physical ports."
With the input policy applied to the port-channel interface, I tried addign the output policy to the physical ports and I got this message:
"A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port."
Is there a way to get the auot-qos policies applied to the port-channel properly?
Based on the business requirement, I have installed one more 9 port FE Switch in addition to existing one, NM is discovered but when we connect PC or IP-Phone it is not working, current IOS is flash:c2800nm-advipservicesk9-mz.124-3h.bin with 64MB Flash
Just want to ask if 4-port serial HWIC-4T is compatible for the Cisco 2801?We need additional HWIC for Fast Ethernet but the problem is we don't have already slot for it.We already have two HWIC-2T 2-port serial which is inserted at slot 1 and slot 3. We're planning to buy 4-port HWIC-4T so we can use the slot 3 for HWIC Fast Ethernet.if it's possible to have the 4-port serial HWIC-4T be inserted to Cisco 2801.
I just installed a HWIC-2T in a Cis co 3845 running IOS 15.1(3) T New build.The IOS self installed the port configuration including the command line "clock rate 2000000." I can edit everything but that entry using the CLI. When I enter the "no clock rate" it will not take in the running conf.
Is the subject line status correct? I have a gigabitethernet port (3845) that went from admin down, to reset and then status Down, protocol Down. Then I had another gigabitethernt port on a different 3845 router. To show port in status of UP and protocol Down, I didn't see a reset occur on this port. Which status is correct and does the reset step affect the final status being different?
