In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
I have got 3845/3945, I would like to increase HWIC slot density for HWIC 4 PORT ISDN BRI S/T ports through the NM/NME/NMX slots, Is there any measns to do that?
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0: Unknown WAN daughter card WIC module not supported/disabled in this slot Hardware Revision : 2.0 Top Assy. Part Number : 800-27738-02 Part Number : 73-10677-02 Board Revision : B0 Deviation Number : 0 Fab Version : 02 PCB Serial Number : FOC******** RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : HWIC-2FE Version Identifier : V01 CLEI Code : COUIAFUCAA Base MAC Address : 001a.6c70.260b MAC Address block size : 2 Connector Type : 01 EEPROM format version 4 EEPROM contents (hex):(code)
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
I put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
The problem is I can't access the router from the internet. I am also an ocean away from the site. I have an ugly hack set up where I access an inside PC with Teamviewer and then puTTy to the router, but it is slow, ugly, and doesn't fix my problem. I need to be able to set up internet accessible servers at this location for VOIP, VPN, and REAL remote access.Everything else works fine. Connection is stable. Speed is kinda ******, but that's not so important.
First off some specs:Cisco 2801c2801-ipvoicek9-mz.124-24.T1.binhwic-3g-cdma-sSprint 3G data plan
Ok, I have set up the previous equipment as a router for a branch office where 3G access is the only available internet access.I have had the excruciating experience of talking with Sprint Tech Support, and would rather shoot myself in the foot than do so again.
Here is what they told me: "They block ports, but they can't tell me which ones."Here is relevant info I have been able to gather.The IP connection the ISP gives us is not NATTED. That is the address at wimi.com and show int dialer 0 is the same one.Most forums say Sprint only blocks port 80.Zenmap (nmap for windows) says the router has NO open ports but DOES exist.Router does not respond to pingsCan't SSH into router from internetCan't access a test local server with port 8080 or 8081 open with the correct nat statement in Cisco routerNo filtering access-list for testing The config should be just fine as a base config for using hwic-3g-cdma-s as the main internet access interface for a router. Everything works fine aside from the lack of remote access.
So in my head it has to be one of 3 problems.
1. The card is doing some weird stuff to incoming requests
2. Sprint is blocking WAN requests on port 22, 2200, 8080, and 8081 and pings (tested). Maybe they block all WAN requests?
3. There is something wrong with my config.
why I can't remote access into my router or things to try with the config?
Below are some config pastes:
chat-script cdma "" "ATDT#777" TIMEOUT 60 "CONNECT" ! ip ssh authentication-retries 2 ip ssh port 2200 rotary 1 ip ssh version 2
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
I am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
I am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.
1841 & 3845 router. We send 30 GB data on 100 Mbps link. First time we use 3845 router for sending the data and 47 Min are required to complete the data, during this link utilization was 100%. After that we send same data through 1841 router & 46 Min are required for the same. Only difference in data transfer is CPU Utilization of 1841 router goes 30% & 5 % of 3845 router Can we use 1841 router instead of 3845 router ? .
I have 3845 router where 200 branches are connect. Ho have database server where branch are synch interval period.some of days observation cpu load average 70 % and sometimes it reaches 100 %.yesterday when I give command clear arp then instant cpu load reduce and 20 % yesterday cpu load 12-20 %. Today morning when I give command Cpu proc history then I found cpu load 60 % and at night it was 3 times reaches 100 %. so my question is after clear arp command at least 10 hours cpu utilization 20 % but after that it increase.so for any LAN broadcast it happend ? how i understand cpu high for Broadcasting or anything else.
I am facing a issue on Cisco 3845 router, IOS is :c3845-adventerprisek9-mz.124-22.YB8.bin
I have changed the IOS as well as the Hardware but again the router is restarting. I have put the show tech-support and crash-info in Output interpreter, result is below:
ERROR MESSAGE NOTIFICATIONS (if any) %PAR-1-FATAL (x): [chars] Explanation: A parity error has occurred. The problem might be caused either by a motherboard that has failed or motherboard settings that are incorrectly set.
I have S384AESK9-124xx (T) version IOS in one of my 3845 router, can i copy the IOS and install it in my 4 x 3845 Router as i require (T) Version IOS to support HWIC-2FE module.
Like wise, i have Cisco 1800 IOS- S184AESK9-124xx (T) and Cisco 2800 IOS- S28NAESK9-124xx (T) installed in my routers, will there be any issues if i copy and use the same IOS in all my respective devices?
we have 3845 routers with internet service providers connected on it.we have configured router bgp 2.xxx as our AS. What is the concept behind router bgp 2.xxx with ISP ?
Can I delete the running IOS from flash on an operational 3845 router to make room for the newer version? The flash isn't large enough to hold two versions. Doesn't the IOS get loaded and run from NVRAM? I don't want to take down an operational router but may have no other choice?
I have a 3825 router running 12.4t IOS. I installed DSU/CSU part number HWIC-1DSU-T1 in the router and it does not recognize it. Is this the right card for this router? Is there anything I can look at to determine the issue? I think the router only has 32M RAM. Below is a show hardware. Card is still currently installed.
